1988 JEEP CHEROKEE coolant temperature

proper increased enrichment for the next engine start. Idle speed is
nonadjustable.
EMISSION CONTROL
The ECU electrically controls Exhaust Gas Recirculation (EGR).\
An ECU-controlled solenoid valve is used to control EGR valve
function. This valve is located on the left inner fender panel and is
operated by the ECU in response to coolant temperature, throttle
position, and manifold pressure.
Under conditions of engine warm-up, engine idle, wide open
throttle, or rapid acceleration/deceleration, the solenoid valve is
energized, blocking vacuum to the EGR valve. At normal operating
temperatures with engine speed above idle, the solenoid valve is de-
energized, allowing normal EGR valve function.
NOTE: If the electrical connector is removed from the EGR solenoid,
EGR flow will be allowed at all times.
A/C CLUTCH CONTROL
The ECU controls the A/C compressor clutch to improve idle
quality. The A/C compressor clutch will be engaged or disengaged as
deemed necessary by the ECU through the A/C clutch relay.
SHIFT LIGHT CONTROL
The shift light system is used on all manual transmission
equipped vehicles. The ECU monitors coolant temperature, throttle
position, vehicle speed, and engine speed to control the shift light.
The ECU calculates what gear position the vehicle should be in and
uses this information to turn on the light. The light indicates the
best shift point to the driver for maximum fuel economy.
The light is tested when the ignition switch is turned on.
When the engine is started, the light should go out. A transmission-
mounted switch prevents the light from illuminating when the
transmission is shifted into high gear. The ECU turns the light off if
the shift to the next higher gear is not performed within 3-5 seconds
after light comes on.
DIAGNOSIS & TESTING
PRELIMINARY CHECKS
Before assuming that the ECU is faulty, the following systems
and components must be in good condition and operating properly:
* Air filter.
* All support systems and wiring.
* Battery connections and specific gravity.
* Compression pressure.
* Electrical and vacuum connections to components, sensors and
switches.
* Emission control devices.
* Ignition system.
* All vacuum and fuel line (hose) connections.
FUEL SYSTEM TEST
Fuel Pressure
1) Remove cap from pressure test port on fuel rail and

COMPONENT TESTING
Throttle Position Sensor
See THROTTLE POSITION SENSOR DIAGNOSTICS chart near the end
of this article. See Fig. 8.
Coolant Temperature Sensor (CTS) &
Manifold Air Temperature (MAT) Sensor
1) Disconnect the electrical connector from the sensor. Using
a high impedance, digital volt/ohmmeter, measure the resistance of the
sensor. If measured resistance is not as specified, replace sensor.
See the CTS & MAT SENSOR TEMPERATURE-TO-RESISTANCE VALUE table.
2) Test electrical harness resistance of both sensors by
testing between ECU harness connector "D-3" and sensor connector. Also
test between sensor connector and ECU harness connector "C-10" ("C-8"
on MAT sensor). Repair wire if open circuit is detected. Repair MAT
sensor wiring harness if resistance is greater than one ohm.
CTS & MAT SENSOR TEMPERATURE-TO-RESISTANCE VALUE









\









\









\









\









\






F(C) Ohms
212 (100) .................................. 185
160 (71) ................................... 450
100 (38) .................................. 1600
70 (21) ................................... 3400
40 (4) .................................... 7500
20 (-7) ................................. 13,500
0 (-18) ................................. 25,000
-40 (-40) .............................. 100,700









\









\









\









\









\






Manifold Absolute Pressure (MAP) Sensor
NOTE: Terminal identification letters are stamped on MAP sensor
body.
1) Disconnect electrical connector from sensor. With ignition
on and engine stopped, measure voltage output of sensor terminal "B".
See Fig. 4 . Ensure wiring harness is okay by also measuring voltage at
ECU terminal "C-t". Output voltage should be 4-6 volts at both points.
Repair or replace wiring harness as required.
2) With ignition on and engine stopped, measure supply
voltage of sensor terminal "C". See Fig. 4. Ensure wiring harness is
okay by also measuring voltage at ECU terminal "C-14". Supply voltage
should be 4.4-5.5 volts at both points. Repair or replace wiring
harness as required.
3) Using an ohmmeter, measure ground circuit resistance at
sensor terminal "A" and ECU connector terminal "D-3". Ensure wiring
harness is okay by also measuring resistance between ECU terminal "D-
3" and "B-11". If ohmmeter indicates an open circuit, check for
defective sensor ground connection at right side of cylinder block.
4) If ground connection is okay, replace ECU. If ECU terminal
"D-3" has short to 12-volts, repair wire before replacing ECU. Repair
or replace wiring harness as required.

ELECTRONIC CONTROL UNIT (ECU)
Removal & Installation
Information not available from manufacturer.
COOLANT TEMPERATURE SENSOR (CTS)
Removal & Installation
Drain cooling system. Remove air cleaner assembly. Disconnect
electrical connector and remove sensor from block. To install, reverse
removal procedure. Refill cooling system.
OXYGEN (O2) SENSOR
Removal & Installation
Raise and support vehicle. Disconnect electrical connector
from sensor. Remove sensor from exhaust manifold. Install and tighten
sensor to 35 ft. lbs. (47 N.m). Reconnect electrical connector. Lower
vehicle.
THROTTLE POSITION SENSOR (TPS)
Removal
Disconnect electrical connector from TPS. Bend lock tabs away
from retaining screws and remove screws. Remove TPS.
Installation
With throttle valve in normal closed position, install TPS.
Install TPS retaining screws. Perform OUTPUT CHECK.
NOTE: Throttle position sensor is nonadjustable. Only output
voltage can be monitored.
Output Check (Manual Transmission Only)
1) Connect negative lead of digital voltmeter to terminal "B"
and positive lead to terminal "A" of TPS connector. Do not disconnect
electrical connector. Insert leads through back of connector. It may
be necessary to remove throttle body from vehicle to gain access to
connector.
2) Turn ignition on, engine off. With throttle closed and
resting against idle stop, input voltage should be about 5 volts. Move
positive lead from terminal "B" to terminal "C" and read voltage
output. Output voltage should be about 0.8 volt with throttle closed
and resting against idle stop.
3) If voltage is not as specified, loosen lower retaining
screw and pivot sensor for large adjustments. Loosen upper retaining
screw and pivot sensor for small adjustments. Adjust sensor so output
voltage reading equals 16 percent of input voltage. If voltage
specifications cannot be obtained, replace sensor. Remove voltmeter.
Tighten screws and bend retaining tabs into position.
ALL OTHER SENSORS, SOLENOIDS & SWITCHES
Removal & Installation
Removal of sensors, switches, and solenoids is accomplished
by disconnecting the electrical and/or vacuum connectors and removing
or detaching the component. To install, reverse removal procedure.
TESTING
NOTE: Refer to Figs. 8-10 for Testing information.

CO Carbon Monoxide 

CO2 Carbon Dioxide 

CONV Convertible 

CP Canister Purge 

CPA Connector Position Assurance 

CPS Crank Position Sensor 

CTS Coolant Temperature Sensor 

CV Check Valve or Constant Velocity 

CVC Constant Vacuum Control 

CW Clockwise 

CYL or Cyl. Cylinder 

Calif. California 

Carb. Carburetor 

Chrg. Charging 

Circ. Circuit 

Cntrl. Control 

Comp. Compressor or Compartment 

Conn. Connector 

Cont. Continued 

Conv. Convertible or Converter 

Cu. In. Cubic Inch 

Cyl. Cylinder 











\








\









\









\









\









\









\





\f

"D" ABBREVIATION TABLE
"D" ABBREVIATION TABLE







\









\








\









\









\









\









\






 
ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






"D" Drive 

DBC Dual Bed Catalyst 

DC Direct Current or Discharge 

DDD Dual Diaphragm Distributor 

DERM Diagnostic Energy Reserve Module 

DFI Digital Fuel Injection 

DIC Driver Information Center 

DIS Direct Ignition System 

DIS Distributorless Ignition System 

DIST Distribution 

DISTR Distributor 

DK BLU Dark Blue 

DK GRN Dark Green 

DME Digital Motor Electronics (Motronic System) 

DOHC Double Overhead Cam 

DOT Department of Transportation 

DP Dashpot 

DRB-II Diagnostic Readout Box 

DVOM Digital Volt/Ohm Meter (see VOM) 

Def. Defogger or Defroster 

Def. Defrost 

Defog. Defogger 

Diag. Diagnostic 

Dist. Distributor or Distribution 

Dr. Door 











\








\









\









\









\









\









\





\f

"E" ABBREVIATION TABLE
"E" ABBREVIATION TABLE







\









\








\









\









\









\









\








ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






EAC Electric Assist Choke 

EACV Electric Air Control Valve 

EBCM Electronic Brake Control Module 

ECA Electronic Control Assembly 

ECAT Electronically Controlled Automatic Transaxle 

ECM Electronic Control Module 

ECT Engine Coolant Temperature Sensor 

ECU Electronic Control Unit or Engine Control Unit 

EDF Electric Drive Fan relay assembly 

EDIS Electronic Distributorless Ignition System 

EEC Electronic Engine Control 

EECS Evaporative Emission Control System 

EEPROM Electronically Erasable PROM 

EFE Early Fuel Evaporation 

EFI Electronic Fuel Injection 

EGO Exhaust Gas Oxygen sensor (see HEGO) 

EGR Exhaust Gas Recirculation system 

EGRC EGR Control solenoid or system 

EGRV EGR Vent solenoid or system 

EMR Emission Maintenance Reminder Module 

ESA Electronic Spark Advance 

ESC Electronic Spark Control 

EST Electronic Spark Timing 

ETR Emergency Tensioning Retractor 

EVAP Fuel Evaporative System 

EVIC Electronic Vehicle Information Center 

EVO Electronic Variable Orifice 

EVP EGR Valve Position Sensor 

EVR EGR Valve Regulator 

EVRV Electronic Vacuum Regulator Valve 

Elect. Electronic 

Eng. Engine 

Evap. Evaporative 

Exc. Except 











\








\









\









\









\









\









\





\f

"F" ABBREVIATION TABLE
"F" ABBREVIATION TABLE







\









\








\









\









\









\









\






 
ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






F Fahrenheit (Degrees) 

F/B Fuse Block 

FBC Feedback Carburetor 

FI Fuel Injector or Fuel Injection 

FICD Fast Idle Control Device 

FIPL Fuel Injector Pump Lever 

FP Fuel Pump 

FPM Fuel Pump Monitor 

FPR-VSV Fuel Pressure Regulator Vacuum Switching Valve 

FWD Front Wheel Drive 

Fed. Federal 

Ft. Lbs. Foot Pounds 











\








\









\









\









\









\









\





\f

"G" ABBREVIATION TABLE
"G" ABBREVIATION TABLE







\









\








\









\









\









\









\








ABBREVIATION DEFINITION 

of the scale, a symbol for defroster indicates defrost position. In
"BI-LEVEL" position, a mixture of floor heat and defroster air is
obtained.
The lower temperature control lever operates blend-air door
in heater core housing. At full right position, all air is directed
through heater core, providing maximum heat flow. At full left
position, all air is directed around heater core providing fresh air.
Control can be set in any intermediate position to provide a blend of
heated and unheated air. Heater must be in heat or defrost mode before
any air can enter vehicle.
TROUBLE SHOOTING
See JEEP TROUBLE SHOOTING at the end of this article.
REMOVAL & INSTALLATION
CONDENSER
Removal (Cherokee, Comanche & Wagoneer) NOTE: On these
models, condenser and receiver-drier are replaced
as a unit.
1) Drain radiator. Disconnect fan shroud and radiator hoses.
Disconnect automatic transmission cooler lines (if equipped).
Discharge A/C system using approved refrigerant recovery/recycling
equipment.
2) Disconnect A/C hoses from condenser. Unplug low pressure
switch. Remove radiator and condenser as an assembly. Detach condenser
retaining bolts. Separate condenser from radiator. Remove receiver-
drier from condenser.
NOTE: Plug receiver-drier openings whenever unit is removed from
condenser. Add 1 oz. of refrigerant oil (AMC No. 8132400) to
system when replacing condenser.
Installation
To install, reverse removal procedure. Fill radiator.
Evacuate, leak test, recharge and check A/C system operation.
Removal (Wrangler)
1) Discharge system (slowly to prevent loss of compressor
oil) using approved refrigerant recovery/recycling equipment. Drain
coolant. Remove fan shroud and radiator. Disconnect pressure line at
condenser. Remove condenser mounting screws. Tilt bottom of condenser
toward engine.
2) From underside of vehicle, disconnect hose attaching
receiver-drier to evaporator. Plug all openings to prevent entry of
dirt or moisture. Remove receiver-drier and condenser assembly. Remove
receiver-drier from condenser.
Installation
To install, reverse removal procedure. Fill radiator.
Evacuate, leak test, recharge and check A/C system operation.
RECEIVER-DRIER
NOTE: On Cherokee, Comanche and Wagoneer, receiver-drier is
removed with condenser and radiator as an assembly.
Removal (Wrangler)

EG R F U NCTIO N T E STIN G

1988 J e ep C hero ke e
1983-88 Exhaust Emission Systems
JEEP EXHAUST GAS RECIRCULATION
TESTING
EGR VALVE
Valve Opening Test
1) With engine at normal operating temperature and at idle,
rapidly open and close throttle. Open throttle sufficiently to obtain
at least 1500 RPM. Movement should be noticed in EGR diaphragm.
2) If diaphragm does not move, probable causes are: faulty
vacuum signal to EGR, defective EGR diaphragm or defective
backpressure sensor diaphragm (if equipped), or leaks in vacuum lines
or connections.
Valve Closing Test
1) With engine at normal operating temperature and at idle,
manually depress EGR valve diaphragm. RPM should immediately drop,
indicating that EGR valve is not leaking and had been properly
cutting off exhaust gas flow at idle.
2) If there is no change in RPM and engine is idling
properly, exhaust gases are not reaching combustion chamber. Check
for plugged passage between EGR valve and intake manifold.
3) If engine idles poorly and RPM is not greatly affected by
manually moving diaphragm up, EGR valve is not closing off exhaust
gas flow. Check for carbon between pintle, leaking EGR valve gasket
or bad EGR valve.
COOLANT TEMPERATURE OVERRIDE (CTO) SWITCH
NOTE: Engine coolant temperature must be below 100F (38C) to
perform this test.
1) Check vacuum lines for leaks and correct routing.
Disconnect vacuum line at backpressure sensor (if equipped) or at EGR
valve, and attach this line to vacuum gauge.
2) Operate engine at 1500 RPM. No vacuum should be indicated
on gauge. If vacuum is shown, replace CTO switch.
3) Idle engine until coolant temperature exceeds 100
F
(38C) on 4-cylinder engines, or 115F (46C) on 6-cylinder and V8
engines.
4) Raise engine speed to 1500 RPM. Ported vacuum should be
shown on gauge. If not, replace CTO switch.
DUMP VALVE
1) With engine at normal operating temperature, remove dump
valve vacuum hose from manifold and plug manifold connection.
2) Raise engine speed to 2000 RPM. Vacuum should be present
at exhaust ports on bottom of valve. If not, replace valve.
3) Reconnect vacuum hose to manifold and raise engine speed
to 2000 RPM. No vacuum should be felt at exhaust ports on bottom of
valve. If vacuum is present, replace valve.
THERMAL VACUUM SWITCH (TVS)
1) With the air cleaner temperature below 40F (-4C),
disconnect vacuum hoses from TVS and connect vacuum source to large

EG R S YSTE M

1988 J e ep C hero ke e
1983-88 Exhaust Emission Systems
JEEP EXHAUST GAS RECIRCULATION
DESCRIPTION
Purpose of the Exhaust Gas Recirculation (EGR) system is to
limit formation of oxides of nitrogen (NOx) emissions. This is done by\
reducing high peak combustion temperatures at which NOx is formed. By
reintroducing some exhaust gas back into combustion chamber, high
temperatures are avoided. Thus NOx emissions formation is reduced.
System consists of vacuum-operated EGR valve and coolant
temperature override (CTO) switch. In addition, some models are
equipped with air cleaner-mounted thermal vacuum switch (TVS), and
some are equipped with an EGR vacuum dump valve.
OPERATION
When the EGR valve receives vacuum signal, through the CTO
switch, EGR valve opens and meters gases from exhaust manifold into
intake manifold. Individual component operation is as follows:
EGR VALVE
EGR valve is mounted on intake manifold. Exhaust gas is drawn
from exhaust crossover passage or exhaust manifold. Two types of EGR
valves are used: valve without backpressure sensor and valve with
integral backpressure sensor.
EGR Valve W/O Integral Backpressure Sensor
EGR valves are calibrated by use of different shapes of valve
pintles or orifices. Valve is normally held closed by spring (above
diaphragm). Valve opens by overcoming spring tension when vacuum is
sensed through coolant temperature override switch (CTO) and
backpressure sensor (if equipped).
EGR Valve W/Integral Backpressure Sensor
Calibration is accomplished by use of different diaphragm
spring loads and flow control orifices. This integral type unit
combines EGR valve and backpressure sensor functions into one
component. Restrictor plate is required with some engines.
Exhaust gas exerts backpressure inside exhaust manifold
whenever engine is running. This pressure is conducted through hollow
pintle stem into EGR diaphragm control chamber. If this pressure is
great enough to overcome spring tension against diaphragm, diaphragm
is moved against bleed valve and exhaust gas flow begins.
COOLANT TEMPERATURE OVERRIDE (CTO) SWITCH
Coolant temperature override (CTO) switch is located in
coolant passage at cylinder head or coolant passage at intake
manifold.
Inner port of switch is connected to EGR port on intake
manifold and outer port is connected to EGR valve, or EGR-TVS. Switch
opens at a preset temperature. Below these temperatures, no EGR is
possible.