1988 JEEP CHEROKEE automatic transmission fluid
[x] Cancel search: automatic transmission fluidPage 965 of 1378
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \
Transfer Case
1985-86
Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \
Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \
1987
Selec-Trac ................................. 2.5 Pts. (1.2L)
Command-Trac ............................... 2.2 Pts. (1.0L)
1988
Selec-Trac ................................. 3.0 Pts. (1.4L)
Command-Trac ............................... 2.2 Pts. (1.0L)
Drive Axles (
3)
Front ........................................ 2.5 Pts. (1.2L)
Front (Disconnect Housing) .................. 5.0 Ozs. (0.15L) \
Rear ......................................... 2.5 Pts. (1.2L)
Rear (Trac-Lok) (
4) .......................... 2.5 Pts. (1.2L)
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
(
2) - Includes 2.3 qts. for coolant recovery bottle.
(
3) - Fill to bottom of filler plug hole.
(
4) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive first, then add new fluid.
\
\
\
\
\
\
\
\f
Page 966 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual 22,500 MILE (36,000 KM) SERVICE
22,500 MILE (36,000 KM) SERVICE \
\
\
\
\
\](/manual-img/16/57037/w960_57037-965.png "JEEP CHEROKEE 1988 Service Repair Manual 22,500 MILE (36,000 KM) SERVICE
22,500 MILE (36,000 KM) SERVICE \
\
\
\
\
\")
22,500 MILE (36,000 KM) SERVICE
22,500 MILE (36,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Check Fluid Levels
\b\
\
\
\
\
\
\
Check Fuel Lines, Connections and Valves (CNG Models)
\b\
\
\
\
\
\
\
Check Cooling System Hoses and Clamps
\b\
\
\
\
\
\
\
Check Exhaust System & Heat Shielding
\b\
\
\
\
\
\
\
Lube Parking Brake Ratio Lever Pivot
\b\
\
\
\
\
\
\
Lube Manual Gearshift Control (4WD Transfer Case)
\b\
\
\
\
\
\
\
Inspect C/V Joint boots (4WD)
\b\
\
\
\
\
\
\
Inspect Underside of Vehicle (Bolts & Threaded Fasteners)
\b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear
\b\
\
\
\
\
\
\
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Inspect/Repack Front Wheel Bearings (2WD Models)
\b\
\
\
\
\
\
\
Inspect Front Brake Pads & Rotors
\b\
\
\
\
\
\
\
Lubricate Caliper Slide Rails
\b\
\
\
\
\
\
\
Inspect Rear Brake Linings & Drums
\b\
\
\
\
\
\
\
Inspect Brake System Hoses & Lines
\b\
\
\
\
\
\
\
Inspect Shocks for Leakage
\b\
\
\
\
\
\
\
Inspect Tire Wear Pattern
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure (Including Spare)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Page 967 of 1378
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \
Page 969 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\](/manual-img/16/57037/w960_57037-968.png "JEEP CHEROKEE 1988 Service Repair Manual Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\")
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Suspension Bushings, Springs, Arms & Rear Jounce Bumpers
\b\
\
\
\
\
\
\
Parking Brake System
\b\
\
\
\
\
\
\
Lubricate Body Components
\b\
\
\
\
\
\
\
Inspect Shocks for Leakage
\b\
\
\
\
\
\
\
Inspect Tire Wear Pattern
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure (Including Spare)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Air Filter Element
\b\
\
\
\
\
\
\
PCV Filter
\b\
\
\
\
\
\
\
Fuel Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
Page 970 of 1378
(3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \
Transfer Case
1985-86
Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \
Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \
1987
Selec-Trac ................................. 2.5 Pts. (1.2L)
Command-Trac ............................... 2.2 Pts. (1.0L)
1988
Selec-Trac ................................. 3.0 Pts. (1.4L)
Command-Trac ............................... 2.2 Pts. (1.0L)
Drive Axles (
3)
Front ........................................ 2.5 Pts. (1.2L)
Front (Disconnect Housing) .................. 5.0 Ozs. (0.15L) \
Rear ......................................... 2.5 Pts. (1.2L)
Rear (Trac-Lok) (
4) .......................... 2.5 Pts. (1.2L)
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
(
2) - Includes 2.3 qts. for coolant recovery bottle.
(
3) - Fill to bottom of filler plug hole.
(
4) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive first, then add new fluid.
\
\
\
\
\
\
\
Service Labor Times
\
\
\
\
\
\
\
Application ( 1) Hours
2.5L
Automatic Transmission ................................... 5.6
Page 971 of 1378
Manual Transmission ...................................... 4.9
2.8L
Automatic Transmission ................................... 5.8
Manual Transmission ...................................... 5.1
4.0L
Automatic Transmission ................................... 5.7
Manual Transmission ...................................... 5.0
(
1) - Add .8 hr. for vehicles equipped with 4WD.
\
\
\
\
\
\
\
\f
37,500 MILE (60,000 KM) SERVICE
37,500 MILE (60,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Check Fluid Levels
\b\
\
\
\
\
\
\
Check Fuel Lines, Connections
\b\
\
\
\
\
\
\
Check Cooling System Hoses and Clamps
\b\
\
\
\
\
\
\
Check Exhaust System & Heat Shielding
\b\
\
\
\
\
\
\
Inspect Brake System
\b\
\
\
\
\
\
\
Inspect C/V Joint boots (4WD)
\b\
\
\
\
\
\
\
Inspect Underside of Vehicle (Bolts & Threaded Fasteners)
\b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear
\b\
\
\
\
\
\
\
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure (Including Spare)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter, if it has not been changed in the last 12 months
\b\
\
\
\
\
\
\
Manual Transmission Fluid
\b\
\
\
\
\
\
\
Automatic Transmission Fluid, Filter and Adjust Bands
\b\
\
\
\
\
\
\
Transfer Case Fluid
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Page 972 of 1378
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
Page 974 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual \b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear](/manual-img/16/57037/w960_57037-973.png "JEEP CHEROKEE 1988 Service Repair Manual \b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear")
\b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear
\b\
\
\
\
\
\
\
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Lube Parking Brake Ratio Lever Pivot
\b\
\
\
\
\
\
\
Lube Manual Gearshift Control (4WD Transfer Case)
\b\
\
\
\
\
\
\
Inspect/Repack Front Wheel Bearings (2WD Models)
\b\
\
\
\
\
\
\
Inspect Front Brake Pads & Rotors
\b\
\
\
\
\
\
\
Lubricate Caliper Slide Rails
\b\
\
\
\
\
\
\
Inspect Rear Brake Linings & Drums
\b\
\
\
\
\
\
\
Inspect Brake System Hoses & Lines
\b\
\
\
\
\
\
\
Inspect Shocks for Leakage
\b\
\
\
\
\
\
\
Inspect Tire Wear Pattern
\b\
\
\
\
\
\
\
Lubricate Weatherstripping with Silicone
\b\
\
\
\
\
\
\
Lubricate Door Hinges
\b\
\
\
\
\
\
\
Lubricate Door Locks
\b\
\
\
\
\
\
\
Check Body Drain Holes
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\b\
\
\
\
\
\
\
Automatic Transmission Fluid, Filter and Adjust Bands
\b\
\
\
\
\
\
\
Flush and Fill Engine Coolant, if not done in last 36 months
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5