1987 NISSAN PULSAR wheel

Fuel and Engine Management 97
circuitry do not immerse it in cleaning
solvent as this may result in irreparable
damage.

Installation is a reversal of the removal procedure
with attention to the following points:

(1) Lubricate the new O ring seals with auto-
matic transmission fluid prior to installing them to the
injector. If removed, ensure that the lower filter screen
is installed. (2) Firmly push the injector into the throttle
body assembly until it is fully seated, ensuring that the
injector connection terminals face towards the rear of
the vehicle.
(3) Apply Loctite 262 to the injector retaining
plate screw and tighten securely.
(4) Start the engine and check for fuel leaks as
previously described.
(5) Install the air cleaner and tighten the retain-
ing nuts securely.
FUEL METER ASSEMBLY - 1.6 LITRE
ENGINE

To Remove and Install
(1) Remove the injector as previously described.
(2) Mark the fuel supp ly and return hoses,
release the clamps and disconnect the hoses from the
fuel meter assembly.
(3) Remove the air cleaner assembly base gasket
from the fuel meter assembly. (4) Remove the bolts and screws securing the
fuel meter assembly to the throttle body and remove the fuel meter assembly. Remove and discard the
gasket.

(5) If necessary, remove the fuel pressure regu-
lator as previously described.

Installation is a reversal to the removal procedure
with attention to the following points;

(1) If removed, install the fuel pressure
regulator
as previously described.
(2) Place a new gasket on the throttle body,
aligning the holes in the gasket with those in the
throttle body, ensuring that the idle air passage is not
blocked. (3) Coat the fuel meter assembly retaining
screws with Loctite 26 2 and tighten securely.
(4) Install the fuel meter assembly retaining bolts
and tighten to the specified torque.
(5) Connect the fuel supply and return hoses and
tighten the clamps securely. (6) Install the injector as previously described.
(7) Start the engine and check for fuel leaks.
Rectify as necessary. (8) Install the air cleaner assembly.
FUEL TANK

To Remove and Install
(1) Depressurize the fuel system as previously
described.
(2) Disconnect the negative battery terminal.
(3) Remove the fuel pump cover plate retaining
screws, disconnect the wi ring harness rubber grommet
from the cover plate and remove the cover plate from
the wiring harness. (4) Raise the rear of the vehicle and support it
on chassis stands. Refer to the Wheels and Tires
section if necessary. (5) Remove the fuel tank drain plug and drain
the fuel into a petroleum resistant container. (6) Mark the fuel hoses and disconnect the hoses
from the fuel pump.
(7) Disconnect the hoses from the fuel filler neck
pipe, the fuel check valve and the fuel tank breather
pipe.
View of the fuel meter assembly removed from the
throttle body. HANDBRAKE CABLE MOUNTING
Installed view of the fuel tank.

Fuel and Engine Management 115
Erase the fault codes and retest for fault codes as
follows:

(2) Start and run the engine until normal oper-
ating temperature is attained. (3) Drive the vehicle at a speed of at least 80
km/h and, with the throttle closed, allow the vehicle to
decelerate until the engine speed is below 1 500 rpm.
NOTE: After rectifying any fault it will be
necessary to retest for fault codes. To test for
Code 24 the vehicle must be driven as
previously described.

(4) Switch the engine Off and connect a jumper
lead between terminals A and B on the diagnostic link
connector. Switch the ignition On and note the fault
codes. If code 24 is displayed proceed as follows. (5) Check the operation of the speedometer and
the instrument cluster warning lamps. If the speed-
ometer only is not functioning, proceed to operation
(13).
If the speedometer and the instrument cluster
warning lamps are not functioning, a fault in the
instrument cluster wiring harness is indicated. Refer
the fault to an auto electrical workshop or a Nissan
dealer.

If the speedometer is functioning, proceed as
follows:

(6) Raise the front of the vehicle and support it
on chassis stands. (7) Place the transaxle in Neutral and switch the
ignition On. (8) With the aid of assistants, slowly spin the
front wheels by hand while backprobing the control
unit wiring connector terminal A10 with a digital
voltmeter to earth. The voltage should alternate from under 1 volt to
over 10 volts.

If the voltmeter readi ng is not as specified,
proceed to operation (9).

If the voltmeter reading is as specified, the vehicle
speed sensor is operating satisfactorily, indicating an
intermittent fault was the cause of the fault code.
Proceed as follows:

(a) Check for faulty wiri ng connections. Check
that all wiring connectors are clean and secure. (b) Check that all earth c onnections are secure.
(9) Remove the instrument cluster as described
in the Electrical System section. (10) With the ignition switched On, backprobe
the control unit wiring connector terminal A10 with a
voltmeter to earth. The voltage should be over 10
volts. If the voltage is less than specified, check the
wiring harness for shorts to earth between the black
and yellow wire terminal on the instrument cluster
wiring connector and the control unit connector
terminal A10. Repair or renew the wiring harness as
necessary. If no fault can be found, renew the control
unit.

(11) With the ignition switched On, backprobe
the black and yellow wire terminal on the instrument
cluster wiring connector with a voltmeter to earth.
The voltage should be over 10 volts.

If the voltage is less than specified, locate the open
circuit between the instrument cluster black and
yellow wire terminal and the control unit wiring
connector terminal A10. Repair or renew the wiring
harness as necessary.

(12) With a test lamp connected to 12 volts,
backprobe the black wire terminals on the instrument
cluster wiring connectors. The test lamp should light.

If the test lamp does not light locate the open
circuit between the black wire terminals and earth.
Repair or renew the wiring harness as necessary.

If the test lamp does light, renew the signal
divider circuit board which is located in the instru-
ment cluster.

(13) With the ignition switched On and the
engine not running, disconnect the vehicle speed
sensor wiring connector from the harness connector.
(14) With a test lamp connected to earth, probe
the yellow wire terminal on the harness wiring con-
nector. The test lamp should light. If the test lamp does not light, locate the open
circuit between the yellow wi re terminal and the Fuel
Pump fuse. Repair or renew the wiring harness as
necessary.

(15) With a test lamp connected to 12 volts,
probe the black wire terminal on the harness wiring
connector. The test lamp should light.

If the test lamp does not light, locate the open
circuit between the black wire terminal and earth.
Repair or renew the wiring harness as necessary.

(16) Using a voltmeter measure the voltage at the
red wire terminal on the harness wiring connector.

If the voltage is 5-9 volts proceed to operation
(19).

If the voltage is over 9 vol ts proceed to operation
(18).

Installed view of the vehicle speed sensor.

116 Fuel and Engine Management


Rear view of the instrument cluster showing the flexible printed circuit.
If the voltage is under 5 volts proceed as follows.
(17) Check the wiring harness for continuity or
shorts to earth between th e red wire terminal on the
speed sensor harness connector and the green and
black wire terminal on th e instrument cluster wiring
connector.

If no fault can be found check the instrument
cluster printed circuit for continuity or shorts. If no
fault can be found, renew the speedometer and the
signal divider circuit board.

(18) Remove the instrument cluster as described
in the Electrical System se ction and repeat operation
(16).

If the voltage is under 1 volt, check the flexible
printed circuit on the rear of the instrument cluster for
continuity or shorts and re new as necessary. If no fault
can be found, renew the speedometer and the signal
divider circuit board.

(19) Connect the harness connector to the vehicle
speed sensor wiring connector. (20) Raise the front of the vehicle and support it on chassis stands. Place the transaxle in Neutral.

(21) With the aid of assistants, slowly spin the
front wheels by hand while backprobing the brown
wire terminal on the vehicle speed sensor wiring
connector with a voltmeter to earth.

The voltage should alternate between approxi-
mately 1 and 7 volts.

If the voltage is as specif ied, check the flexible
printed circuit on the rear of the instrument cluster for
continuity or shorts. If no fault can be found, renew
the speedometer and the signal divider circuit board.

If the voltage is not as specified, proceed as
follows.

(22) Disconnect the vehicle speed sensor wiring
connector and unscrew the sensor from the speedom-
eter drive housing. (23) Rotate both front wheels in the same direc-
tion and check that the speedometer drive shaft is
turning and does not slip. If the drive shaft does not operate as described,
renew the drive assembly as described in the Manual
or Automatic Transaxle section.

If the drive shaft operates satisfactorily, renew the
vehicle speed sensor.

To Remove and Install
(1) Disconnect the negative battery terminal.
(2) Disconnect the vehicle speed sensor wiring
connector. (3) Unscrew the vehicle speed sensor from the
speedometer drive housing.
Installation is a reversal of the removal procedure
with attention to the following points:

(1) Align the cut-out in the speedometer drive
shaft with the notch in the vehicle speed sensor shaft.
(2) Tighten the vehicle speed sensor securely.

118 Emission Control


Installed view of the charcoal canister.
When the engine is at rest, fuel vapor through
evaporation gradually fills the air space in the fuel
tank. The sealed filler cap pr events the escape of this
vapor and pressure builds up within the system,
forcing the vapor to flow into the charcoal canister
which is located in the engine compartment beneath
the windscreen wiper motor.

The fuel check valve prevents liquid fuel entering
the charcoal canister when the fuel tank is full or the
vehicle is parked on a steep incline. When the engine
is running, the vapor is drawn via a hose from the
charcoal canister to the throttle body and burnt in the
combustion chambers.

TO RENEW CHARCOAL CANISTER
(1) Suitably mark and disconnect the hoses from
the canister. (2) Release the retaining spring and remove the
canister from the engine compartment. Installation is a reversal of the removal procedure.

TO RENEW FUEL CHECK VALVE
(1) Disconnect the negative battery terminal.
(2) Raise the rear of the vehicle and support it
on chassis stands. Remove the left hand rear wheel. (3) Drain the fuel from the fuel tank using a
hand pump or a suitable siphon. Do not siphon fuel
using the mouth.
(4) Remove the hoses from the check valve.
(5) Squeeze the retaining clip and remove the
check valve from the mounting bracket. Installation is a reversal of the removal procedure.

TO SERVICE THE SYSTEM
(1) Inspect the vacuum lines and connectors for
signs of leakage, cracks and deterioration and renew
as necessary. (2) Remove the fuel tank cap and check that a
slight resistance is felt, when vacuum is applied to the
one-way relief valve in the centre of the cap. Renew the fuel tank cap if no resistance is felt or
if the valve is blocked.

(3) Inspect the fuel tank cap seal for deteriora-
tion. Renew as necessary.

Installed view of the fuel check valve as seen with the
left hand rear wheel removed.
Check the fuel filler cap seal for damage.
23Q/LDZ GAUGE
Line drawing showing a hand vacuum pump.

121
CLUTCH
SPECIFICATIONS
Type................................................... Single dry plate
Operation................................................... Mechanical
Pressure plate type .................................... Diaphragm
Release bearing type .......................Prelubri cated ball
Driven plate:
Outside diameter .................................... 215 mm
Rivet depth limit ....................................0.3 mm
Runout limit .........................................0.5 mm
Maximum spline backlash ...................0.7 mm
Pressure plate:
Diaphragm spring height
(installed) ...................................... 30.5-32.5 mm
Spring finger vari ation limit.....................0.5 mm
Clutch pedal:
Height .............................................. 175-185 mm
Free play ....................................... 12.5-17.5 mm
Release lever free play............................ 2.5-3.5 mm
Flywheel machining limit ...............................0.3 mm
TORQUE WRENCH SETTINGS
Pressure plate bolts.......................................... 29 Nm
Pedal pivot pin nut ......................................... 22 Nm
Cable loc knut.................................................... 4 Nm
Lower clutch housing to engine bolts.............. 21 Nm
Centre and upper clutch housing
to engine bolts .................................................. 49 Nm
1. CLUTCH TROUBLE SHOOTING
CLUTCH SLIPPING
(!) Worn driven plate facing: Check and renew
the clutch driven plate.

(2) Insufficient clutch pedal free play: Check and
adjust the clutch pedal free play. Ensure that the
release lever free play is correct.
(3) Weak or broken pressure plate diaphragm
spring: Check and renew the pressure plate assembly. (4) Worn or scored flywh eel: Machine or renew
the flywheel. Worn or scored pressure plate face: Renew the
pressure plate assembly.


Renew the clutch driven plate if the friction material is
worn down to, or is within 0.3 mm of the rivets.
NOTE: In most cases clutch slippage is first
evident by a marked increase in engine revs,
for no apparent reason, when pulling up a
steep hill. The clutch condition can be
positively diagnosed as follows: With the
handbrake firmly applied, and the rear
wheels chocked, select top gear and release
the clutch with the engine running at ap-
proximately 2 000 rpm. Clutch slippage is
evident if the engine does not stall. Make the
test as quickly as possible to prevent any
further clutch damage.

CLUTCH SHUDDER
(1) Oil on the driven plate facings: Renew the
clutch driven plate. Invest igate and rectify the source
of the oil leak.
(2) Scored pressure plate or flywheel face: Re-
new the pressure plate assembly or machine the
flywheel. (3) Loose or damaged driven plate hub: Check
and renew the clutch driven plate. (4) Loose driven plate facings: Renew the clutch
driven plate. (5) Cracked pressure plate face: Renew the pres-
sure plate assembly.

122 Clutch


Check the engine mountings for damage and deterio- ration.
NOTE: Clutch shudder is usually most
evident when reversing up an incline. As
loose or damaged engine mountings are a
cause for clutch shudder, thoroughly check
the engine mounting rubbers and mounting
hardware for damage or looseness before
removing the clutch for inspection.

CLUTCH GRAB
(1) Oil soaked driven plate facings: Renew the
clutch driven plate. Invest igate and rectify the source
of the oil leak.
(2) Cracked pressure plate face: Renew the pres-
sure plate assembly. (3) Loose or broken engine mountings: Check
and renew the engine mountings as necessary.
(4) Binding release mechanism: Check the oper-
ation of the release mechanism.
NOTE: Visually check the operation of the
cable actuated release mechanism. Check
the inner cable for fraying and jamming in
the outer cable.

INSUFFICIENT CLUTCH RELEASE
(1) Stretched, frayed or broken clutch cable:
Check and renew the clutch cable. (2) Worn or damaged release mechanism: Check
and renew components as necessary. (3) Insufficient pedal height: Check and adjust
the pedal height.
(4) Warped clutch driven plate: Renew the
clutch driven plate. (5) Excessive clutch release lever free play:
Check and adjust the release lever free play to
Specifications.
NOTE: Visually check that the clutch cable
operates the release lever before removing
the clutch for inspection.

RELEASE BEARING NOISE
(1) Dry or worn release bearing: Check and
renew the release bearing.
(2) Damaged pressure plate diaphragm spring;
Check and renew the pressure plate assembly.
NOTE: Lightly depress the clutch pedal with
the engine running to check for release
bearing noise. If the release bearing is faulty
and has to be renewed, always check the
other clutch components.


Check the diaphragm spring fingers for scoring and damage.
2. DESCRIPTION
The clutch consists of a single, dry, driven plate
assembly, splined to slide on the transaxle input shaft.
A diaphragm spring type pr essure plate assembly is
bolted to the engine flywheel.

The driven plate is sandwiched between the
pressure plate and the flywheel and transmits the
drive from the engine to the transaxle.

Cushion rubbers are interposed between the hub
of the driven plate assembly and the plate friction
surfaces in order to cushion the drive.

The release mechanism is actuated by the clutch
pedal through a cable to the release lever and bearing.

Operation of the clutch pedal moves the release
lever which pushes the release bearing into contact
with the diaphragm spring fingers, forcing the dia-
phragm centre towards the flywheel. When the outer
edge of the diaphragm deflects, the clutch is caused to
disengage.

Clutch pedal free play is adjusted at the release
lever end of the clutch cable.

Clutch pedal height is adjusted at the pedal stop
on the pedal mounting bracket located under the
dashboard.

Clutch 123
3. CLUTCH UNIT AND RELEASE MECHANISM

Special Equipment Required:
To Install — Clutch aligning tool
TO REMOVE
(1) Remove the transaxle from the vehicle as
described in the Manual Transaxle section. (2) Mark the pressure plate cover in relation to
the flywheel to ensure installation to the original
location. (3) Progressively loosen and remove the pressure
plate assembly retaining bolts working in a diagonal
sequence across the assembly. (4) Remove the pressure plate and driven plate
assemblies from the flywheel. Note the installed
direction of the driven plate to aid assembly.
(5) Disengage the clips retaining the release
bearing carrier to the release fork and slide the release
bearing assembly out of the clutch housing. Note the
installed position of the re taining clips to aid assem-
bly. (6) Align the release fork retaining pins with the
slots in the clutch housing and remove the pins using
a pin punch.
(7) Remove the release lever and shaft and
withdraw the release fork and return spring from the
clutch housing.
TO CHECK AND INSPECT

(1) Check the driven plate facings. Renew the
driven plate if the facings are worn down to within
0.3 mm of the rivet heads or are gummy and oil
soaked.
(2) Check the driven plate hub cushion rubbers
for deterioration and damage. Renew the driven plate
if the hub is damaged. (3) Mount the driven plate on the transaxle
input shaft and measure the spline backlash at the
outer edge of the driven plate. Renew the driven plate
if the spline backlash is beyond Specifications. (4) Check the pressure pl ate assembly for wear
on the diaphragm spring fingers, cracked diaphragm
spring and a cracked or distorted cover. Check that
the pressure plate face is not badly scored.

(5) Check the flywheel face for heat cracks, burn
marks and scoring. Renew the flywheel if it is badly
scored.

NOTE: Slight glazing or burn marks on the
pressure plate or flywheel faces can be
corrected using emery paper. Minor scoring
on the flywheel face may be corrected by
machining the flywheel.

(6) Rotate the release bearing by hand and check
for noise or roughness. Renew the bearing and carrier
as an assembly if fa ults are found.
(7) Check the release lever and shaft for wear
and damage. Renew as necessary.
(8) Check the release shaft bushes and seal for
wear or damage. Renew as necessary.
(9) Check the release fork for wear and the
return spring for fatigue. Renew as necessary.
TO INSTAL

(1) Sparingly apply lithium base molybdenum
disulphide grease to the tr ansaxle input shaft splines,
release bearing carrier bore and rear contact surfaces,
release shaft bushes and release fork contact surfaces.
Slide the driven plate onto the transaxle input shaft
and remove the excess grease from the splines. (2) Install the release shaft to the clutch housing,
return spring and release fork. Install the retaining pins
Dismantled view of the flywheel, driven plate and
clutch pressure plate.
Dismantled view of the clutch release components.

124 Clutch


Illustration showing the clutch aligning tool. The tool
can be readily fabricated from a length of round section
wood or metal. Dimension A = diameter of the ma-
chined section of the crankshaft. Dimension B - inside
diameter of the driven plate hub.
to the release fork ensuring that the return spring is
correctly anchored.

(3) Install the release bearing to the clutch hous-
ing and install the clips re taining the release bearing
carrier to the release fork. (4) Install the driven plate to the flywheel in the
direction noted on removal. Install the aligning tool to
hold the driven plate in position.
NOTE: Some driven plates are marked
Flywheel side to indicate the correct in-
stalled direction.

(5) Install the pressure plate to the flywheel in the
position marked on removal. (6) Ensure that the driven plate is correctly
centered and install the pressure plate retaining
bolts.
Tighten the bolts progressively in a diagonal sequence
to the specified torque. (7) Install the transaxle to the vehicle as de-
scribed in the Manual Transaxle section. (8) Adjust the clutch pedal height and free play
as described under the Adjustments heading later in
this section.
4. CLUTCH PEDAL

TO REMOVE AND INSTAL
(1) Working in the engine compartment, loosen
the adjusting nut and disconnect the inner clutch
cable from the clutch release lever at the clutch
housing.
(2) Working inside the vehicle, release the inner
clutch cable from the top of the clutch pedal.
(3) Remove the nut from the end of the clutch
pedal pivot pin. (4) Note the installed position of the clutch
pedal return spring and remove the pivot pin from the
clutch pedal.
(5) Remove the clutch pedal from the vehicle
and remove the bush from the clutch pedal. (6) Examine the clutch pedal and the bush for
bend, cracks, wear and damage. Examine the return

Installed view of the clutch pedal.
spring for cracks and fatigue. Renew parts as neces-
sary.

Installation is a reversal of the removal procedure
with attention to the following points:

(1) Lubricate the hook on the top of the clutch
pedal and the pivot pin and bush with lithium base
molybdenum disulphide grease. (2) Install the return spring to the position noted
on removal. (3) If necessary, adjust the pedal height and free
play as described under the Adjustments heading later
in this section.
5. CLUTCH CABLE

TO REMOVE AND INSTAL
(1) Working in the engine compartment, loosen
the adjusting nut and disconnect the inner clutch
cable from the clutch release lever at the clutch
housing.
(2) Release the outer clutch cable retaining nut
and slide the outer cable out of the slot in the
mounting bracket.
View of the clutch cable assembly.