1987 BMW 530I TOURING warning

5
Level Control Systems
System Components
The system consists of the following components:
 Tandem Hydraulic Pump
 Oil Reservoir
 Pressure Reservoir (2)
 Control Valve with Regulating Linkage
 Camber Warning Switch (E32 and E34)
 Rear Shock with LAD Module
 Expansion Hose, Pressure Lines and Distribution block.
Component Layout E32

7
Level Control Systems
Oil Reservoir
The single reservoir stores fluid for both the self-leveling and power steering systems.
Incorporated in the reservoir, is a reed type level warning switch. If the fluid level drops and
the contact closes, a signal is sent to the check control module and a warning will be dis-
played in the instrument cluster matrix display.
The hydraulic fluid required for the self-leveling suspension system varies between models
and installed equipment. The following fluid is used:
 Pentosin CHF 7.1
 Pentosin CHF 11S
 Power Steering Fluid (BMW)
This type of fluid is used because of its
low viscosity and low noise characteris-
tics. It cannot be mixed with other fluid
types.
The self-leveling system fluid type is
always marked on the top of the hydraulic
reservoir. Always use the correct fluid
never mix with another fluid.
When filling the system, be aware of the
status of the level control system. If the
vehicle is loaded, the level will appear to
be low. Do not fill the system unless it is
in the resting state. Otherwise, an over-
flow situation could result.

12
Level Control Systems
Camber Warning Switch (E32 AND E34 Touring)
The self-leveling suspension systems used in the E32 and the E34 Touring are equipped
with a camber warning switch. The switch is mounted on the right rear axle support and
connected through a rod to the semi-trailing arm.
The function of the switch is to warn the driver of an
overload condition or an unsafe driving situation.
If the switch detects a rear wheel camber of -3.5 deg.
A signal is sent to the check control module and dis-
played on the dash.
A time delay of 8 minutes is incorporated to prevent
the warning from being displayed while driving
through turns.
The E38 does not use the camber warning switch
due to the design of the rear suspension.

15
Level Control Systems
Single Axle EHC I System Components (E39/E53)
The EHC system consists of the following components:
 EHC Control Module
 Air Springs (2) with Air Reservoirs
 Rear Axle Level Sensors
 Encapsulated Air Supply (LVA)
 Warning Indicator
Control Module
The Control Module is mounted in the module carrier box in the luggage compartment on
the right side. It contains the processing electronics and final stages for operation of the
EHC system.
The control module receives the following inputs for its processing functions:
 KL 30 & 31 (Power/Ground)
 KL 15
 Left & Right Ride Height Sensors
 K Bus for;
- Vehicle speed
- Engine running
- Door/tailgate - open/closed
E39 Features 06
EHC Module (E39)

17
Level Control Systems
Air Springs
The air spring is made from a flexible rubber material. It
forms an air tight cavity which provides the calculated
spring rate required for the sport wagon.
As the spring compresses downward the bottom edge
of the rubber material rolls along the vertical surface of
the base mount cylinder.
Air is added or removed from the air spring through its
top port. The top port of each spring is connected to a
reservoir and the air supply pipes. The reservoirs are
required to hold additional air due to the compact design
of the springs.
Rear Axle Level Sensors
Hall effect sensors are mounted on the left
and right sides of the rear suspension for
ride height detection. They are pivoted by a
coupling rod through the rear axle swing
arms.
The hall sensors produce a varying voltage
input to the control module as the suspen-
sion height changes.
If the vehicle is equipped with Xenon head-
lights the right side sensor contains an
additional sensor for the automatic head-
light level adjustment system.
Warning Displays
If the system is faulted and off-line or set in the transport mode, the following is displayed:
Basic Cluster:A warning lamp indicator is illuminated used on the basic cluster.
High Cluster: A message is posted in the high cluster matrix display.
E39 Features 07