1984 NISSAN 300ZX checking oil

STEERING SYSTEM
I---
SECTION ST
CONTENTS
STEERING SYSTEM . . . ... ..
STEERING COLUMN . . . .... ..
POWER STEERING SYSTEM -Checking - . ..
POWER STEERING GEAR AND LINKAGE
POWER STEERING
OIL PUMP . .. ... ..
SERVICE DATA AND SPECIFICATIONS (S D S ) . . . . . . . .
SPECIAL SERVICE TOOLS . .. .. ..
Refer to section MA for:
CHECKING WHEEL ALIGNMENT
Toe-in
Front wheel turning angle
BASIC MECHANICAL SYSTEM
Checking drive belts
. ST- 2
ST- 4
.. ST- 6
. . ST- 8
ST-14
. .. .. ST-17
. . . ST-20

POWER STEERING SYSTEM -Checking
Fluid Level Check
Check the fluid level when the fluid IS cold.
Refer to MA section
Power Steering Pump
Belt Tension
Refer to MA section
Fluid Leakage Check
1 Run engine at idle speed or 1,000 rpm
Make sure temperature of fluid
in tank rises to
60 to 80°C (140 to 176°F).
2 Turn steering wheel to right-to-left several
times
3 Hold steering wheel at each "lock" position for
five seconds
and carefully check for fluid
leakage
CAUTION :
0 Do not hold steering wheel at "lock" position
for more than 15 seconds at a time.
0 If fluid leaks at connectors, replace O-ring (if
equipped) Do not overtighten connector as
this can damage O-ring and connector.
- Bleeding Hydraulic System -
1. Raise front end of vehicle until wheels clear
ground
2 While adding fluid, quickly turn steering wheel
fully to right and
left and lightly touch steering
stoppers.
Repeat steering wheel operation until fluid
level no
longer decreases
Repeat step 2 above
3. Start engine.
Hydraulic System Check
Before starting, check belt tension, driving pulley
and tire pressure. (Refer to MA section )
1 Set Tool Open shut off valve Then bled air
(See "Bleeding Hydraulic System" )
ST27091000 lJ263571
L 1 ow pressure
& Direction of 011 flow hose
ET834
2 Run engine.
Make sure temperature of fluid in tank rises to
60 to 80°C
(140 to 176°F).
3 Check pressure with steering wheel fully turned
in left and right
CAUTION:
Do not hold steering wheel at lock position for
more than fifteen seconds.
Standard pressure:
6,669 - 7,257 kPa
(68
- 74 kglcm' ,967 - 1,052 psi at idling)
4
0
0
If oil pressure is below the standard, slowly
close shut-off valve and check pressure
If pressure raises to standard, gear is damaged
If pressure remains below standard, pump
IS
damaged.
Gear may be damaged
If oil pressure is above the standard, pump may
be damaged 5
CAUTION:
Do not close shutoff valve for more than fifteen
seconds.
6 After checking hydraulic system, remove Tool
and add fluid as necessary, then completely
bleed
air out of system
ST-6

POWER STEERlNG OIL PUMP
Inspection
Wash clean all disassembled parts (inside pump) in
suitable cleaning solvent.
PULLEY AND PULLEY SHAFT
0
0
If pulley is cracked or deformed, replace it.
If an oil leak IS observed around pulley shaft oil
seal, replace it.
If serration of pulley or pulley shaft IS de-
formed
or worn, replace it.
0
OIL PRESSURE SWITCH
(Non-turbocharged model)
Operation High-pressure side hydraulic
line pressure kPa (kglcm', psi) ~~
I Turn ON Increasing to 1,961 - 2,942
(20- 30,284 ~ 4271
Turn OFF Decreasing to Approx
981 .2,942 (10 - 30,142 - 427)
Refer to "Hydraulic
System Check" in "POWER
STEERING SYSTEM
- Checking"
Assembly
Assemble 011 pump in the reverse order of dts-
assembly, noting the following instructions
Before installing O-rings and oil seal, apply a
thin coat of power steering fluid to them.
Make certain that O-rings and oil
seal are
installed properly.
Discard old O-ring and oil
seal and install new
ones Be careful of
oil seal direction.
Wiring Diagram -Oil Pressure Switch
FUSE BLOCK
IGNITION SWITCH
I a
Y
Ln v)
E
ENGINE ROOM E I R HARNESS HARNESS
IWhnsl d'
POWER STEERING OIL PRESSURE
SST222A
ST-1 6