1984 NISSAN 300ZX oil pressure

HEADLAMP
0
0
Headlamp Motor Check
0 No
8 Yes
Use an ohmmeter to check for continuity in
headlamp motor circuit while rotating motor
with manual knob
CAUTION.
Prior to performing continuity test, disconnect
ground cable from battery.
Ohmmeter probe
Headlamp Continuity
Yes
No
Alqning mark for
for up posltlon
SEL652D
- Aiming Adjustment
When performing headlamp aiming adjustment, use
ail aiming machine, aiming wall screen or headlamp
tester For operating instructions of any airner, it
should be in good repair, calibrated and used ac-
cording to respective operation manuals supplied
with the unit
If any aimer is not available, aiming adjustment can
be done
as follows
For details, refer to the regulations in your own
country.
CAUTION:
a Keep all tires inflated to correct pressures.
b. Place vehicle and tester on
one and same flat
surface.
c See that there is no load in vehicle (coolant, en-
gine oil filled up to correct level and full fuel
tank) other than
the driver (or equivalent
weight placed in driver's position).
W~=l,ltO(4409I c 'L
-7
, - LO 1300 001
Of headlamps
UPper edge of Vertical centerline ahead of headlamps -x high tntenrw zone
Height of lamp centers I .- 100 141
100 (41 .-
L A
4.. I.. 100 1100 1001 loo (41 (41 / (41 (41
KLeft edge of high intensity zone
= ACCEPTABLE RANGE untt mm (in1
SEL914D
Adjust headlamps so that upper edge and left
edge
of high intensty zone are within the ac-
ceptable range as shown
in the figure above
Dotted lines in illustration show center of
headlamp.
EL-33

METER AND GAUGES - Digital Type Combination Meter
Trouble-shooting (Cont’d)
Go to “Displav Check”
ING OK
Replace meter and
gauge assembly
v
Check oil pressure sensor circuit
OK NG
Go to “Oil Pressure
Sensor Check” Replace meter
and gauge
assembly
Check harness between Replace oil
oil pressure sensor and meter pressure
sensor
1 Disconnect meter harness connector
(black)
2 Measure resistance between @ and @
when engine stopping and running
Ohmmeter
Engine Resistance
Approx 75R or more
Idling Approx 60R or less
SEL672D
“Trip”, ”Ave speed” and “Dist to empty” meters
1 Go to ”Display Check” 1
Go to “Power Unit Check”
Replace trip Replace power unit
meter assembly
Only “Ave speed” meter does not operate
I
I Go to “Display Check“ I
lNG
OK
Replace trip
meter assembly
I Check clock for proper operation I
Check harness between Replace clock
clock and meter
I OK v
Replace trip meter assembly

METER AND GAUGES - Digital Type Combination Meter
Power Unit Check
Voltmeter
terminal
(f) (-)
E -
-%; 0
0
@I
__
@
9
0
0
Remove power unit with harness connected
Perform voltage and continuity tests Refer to
chart below
I Voltage
[VI
Approx 12
Approx 5
Approx 16
Approx 5
Approx 22
Approx 285
Turn ignition switch to "ON"
1 - 1 More than 6
Remarks
Check when no
display appears
For speedometer
For tachometer
For Temp,
Oil, Volt
sause
For Fuel gauge
For "Trip", "Ave
speed"
& "Dirt to
empty" meter
Turn ignition switch to "OFF"
Ohmmeter
Continuity Remarks
Check when no
ground display appears
If specified voltage or continuity is not produced,
replace power unit.
- Boost Sensor Check
1 Connect vacuum pump gauge to boost sensor
vacuum hose
2 Disconnect harness connector from boost
sensor and connect battery and voltmeter
as
shown
3 Apply vacuum pressure to boost sensor by
vacuum pump gauge and measure voltages
Approx.
2.2V at 0 kPa (0 mmHg, 0 inHg)
(Atmospheric pressure)
Approx.
1 3V
at -53.3 kPa (-400 mmHg, -15 75 inHg)
vacuum pump gauge
SEL674D
EL-53

METER AND GAUGES - Digital Type Combination Meter
Fuel Tank Gauge Check
For removal, refer to FE section
Ohmmeter terminal Float
Main gauge
Resistance value
Approx 10 - 20Q
Approx 480 - 520Q
Approx 100 - 1 1 OQ
Approx 4Q or below
Approx
870.930Q
Sub gauge
SEL675D
SEL676D
-Water Temp Sensor Check -
Cylinder head R H side
SEL677D
-Oil Pressure Sensor Check -
-
011 filter 7 \
SEL678D
Ohmmeter
terminal With engine With engine
stopped 1 running (idling)
ca On
+I;'''' I More than 74Q I Less than 60.Q
EL-56

01 L OIL OIL
PRESSURE TEMPERATURE PRESSURE SENSOR SENSOR SENSOR
I
BOOST
SENSOR
v) m r
P 0
%
@ f$& BODY GROUND
m
h
(Instrument harness)
FUSE
BLOCK J
COMBINATION GAUGE
VOLTMETER
GAUGE
4
GAUGE
BOOST METER
TRIMMER
IGNITION SWITCH
ON or START
I G (Main harness)
Turbocharger
model
Nom turbocharger
model
A/T model
M/T model
3
m
-I
m
rn
D
z
U
0
D
C
0
rn
ui
I
z
(D (D Q
T
-I Y
0 (D
0 0
3
0
¶ 9)
¶
9) c
0
(D
-.
E
G)

METER AND GAUGES -Needle Type Combination Gauge
Oil Temp. Sensor Check
1 Warm up engine
2
3
Stop engine and turn ignition switch OFF
Check resistance of
oil temp sensor
SEL695D
- Boost Gauge Trimmer Adjustment -
When boost gauge does not give proper reading,
adjust
0 kPa (0 mmHg, 0 inHg) point with the
trimmer located on interlor upper wall of glove
box
Use a screwdriver to adjust trimmer
For checking oil pressure sensor and boost
sensor, refer to pages EL-53 and 56
EL-70