1981 CHEVROLET MONTE CARLO oil pressure

Downloaded from www.Manualslib.com manuals search engine 2, Never leta child stand ,or kneel on any seat Children who can sit up by
themselves should
be placed on a sealand restrained with the seat belts
provided, When children ride in a rear seat, .they should be restrained with
a lap
belt, When child(en ride in the front seat, they should wear both lap
and shoulder belt If the .shoulder beH irritates the neck or face due to .the child's size, this may be r.educed by placing the child closer to the center
of the
vehicle , If irritalior Is not reduced, place the child in the rear seat
3, General Motors ~iseS that childr"", be restrained properly when riding ,
However. unusual cond~ions may prevent use of restraints. and require
that a small child
stand, If that ~s.lhe'Child should stand on the floor , behind the'driver's seat This will help reduce the chance and/or \he
severity of injury in case of a frontal collision, --'-'-'''"''''''''i''':>' ~7','" ,,.' ;.,,~"".'. _ .. .. ,
TRAILER TOWING
This car is designed and intended to be used mainly to carry people, Towing a
trailer will affect handling , durability and economy , Your safety and satisfaction
depend :,upoQ proper use of correct llqUipmenl. Also , you should avoiq
overloads
and other abusive use,
' The '
!1'lIiximum 1000000trailet: weight youe;mpull with your vehicle depends ,on what special equipffienrfi'as been installed on il,. We do not recommend towing
any
trailer more than 450 kilograms (1.000 pounds) gross trailer weight unless your vehicle has the required 'equipment
.. .... ~ ' °' -"""''1111'''.''-'' .. J~._ .. _ '."'-:,_, :" .,', .... ,,', , ,'" :', : ' . .. ....... :.' .... " ..... : .. , :"',' "'." ,: ",' ,i,.:." .... __ .. -:,:· .. ,,' .. _." . .'~:.,:;.,~')ff';:.' CAUTION: Do not .. try to tow .. • nv:,,. tr-I.-'r ,mqrtt:,_lt)arr ' 2 '2., Idfogranl( (5,000 Pounds) WPU trliler,we~t IlC) 'In.tter what trailer toWing -'equiprrient is instelled. Trai" over iMM maximum-~_iir:nlt.,-c:OuId teriously affect ~ __ vehk:"'. pertormence ; -_durability and
handling, ~_~kf l'esuh. in personal i~~;_-_, ;""_~ ':~.,,:.:.
Information ,on trailer towing ability, speciateq(Jipn1ent required, and optional
equipment available should.be obtained from your dealer . Ask for the trailering
~rocliure, Or, write: Consum~r Helations Department Chevrolet Motor Divfsion,
Warren , Michigan 48090. (In Canada, write to General Motors of Canada
limited , Customer Services Department, Oshilwa , Ontario L IJ 5Z6),
Tires
When towing trailers be sure your tires areprope,ly inflated'to 'the inflation
,
pressure shown 'on the .. Tire Placard on \he driver's door , The allowable
passenger . and cargo load for this vehicle, also.shown on the Tire Placard , is
reduced by the traiter tongue weight whenever . the trailer is attached to the
'v~hicle, See "Service arid Maintenance," Section 5, for more tire informatlon ,
Maintenance
More' frequent service is required when using your vehicle to pull a traileL See
Section A of the Maintenance Schedule folder for Automatic Transmission Fluid , Engine Oil, and Hear Axle Ltibricantchange requirements for. trailering ,
Now and \hen, check that all trailer hitch bolts and nuts are tight Also see the
Maintenance Schedule
foider, and the Index in this manual, for important facts
on belts, cooling system care and brake adjustment.
1-12

Downloaded from www.Manualslib.com manuals search engine Oil! Choke Indicator Light
This light will come on to prov~ a "bulb check", when the ignition is turnee
on, but should go out after the engine is startee. If light fails to come on with
ignition turnee on,
it could indicate a bumee -out bulb , a defective electric
choke heater circuit or a
blown instrument lamp fuse. Have system repairee if
light
does not come on during check.
Occasionally, this light may flicker . momentarily while the engine is running but
this will· not harm ,the ' system. However, if the ,light remains on during normal
engine operation , the engine shoutd be stopped until the cause of the
trouble can be Iocatee .andcorrectee. The source of the troubte could be any of the following.
•
Loss of engine oil pressure.
• Blown "Choke Heater" or Gage fuse.
• Loss of electric choke heater vo~age.
NOTICE: Continuing to run the engine with an illuminated oil/choke pressure light can cause serious damage to the engine or unusually high exhaust system temp*'ratures which could resuh in serious d8mage to the vehicte.
Choke Warning Indicator Light
On some vehicles equippec with tlie optional .Oil pressure gage, an amber
choke warning indicator
-light replaces the red oil pressure ' indicator light in the
instrument cluster. If this light comes on, indicating loss of electric choke
heater voltage , have your authorizee
Oealer locate and correct the trouble as
soon as possible.
Generator Indicator Light
The red .light VOLT is designee to come on when the ignition.key is in the "run " pos~ion,bul t>efiJrethe 'engine;;, startee. After the engine starts, the
light should go out and remain oul.
H the light remains on when engine is
running , have your Authorized Dealer locate and correct ' the trouble as soon as
possible .
Engine Temperature Indicator Light
This indicator light is providee .in the instrument cluster to. quickly warn of an
overheated engine. 'With the ignition in the START position, the ree TEMP
indicator (hot light) will light to
let you know that it is operating properly.
When the engine is starlee,
the ree light will go out immediately. tt will light up
at no other time unless for some
reason the engine reaches a dangerously
high operating temperature. Glance .at the instrument cluster freqtJentiyas you
drive, if this light is on see
"Engine Cooing System" on page 3,3.
Brake System Warning Light
The regular braking system is a dual system designee so that one part will
provide some braking action
n there is a loss of hydraulic pressure in the other
part of the system. The system has a "Brake" warning Ught Iocatee in the
instrument · panel.
• To serve as a reminder, the "6RAKE" light is designee to stay on when
the parking brake is not fully released and the ignition key is on.

Downloaded from www.Manualslib.com manuals search engine When the ignition key is turned to the OFF position, the pointer may nO\". necessarily return to the 0 RPM position. For the tachometer to regster 0 RPM .
the key
must be in the RUN position and engine not running.
Engine Temperature Gage
This gage indicates coolant temperature which will vary with air temperature
and operating
cond~ions. The ignition must be on for accurate readings. Hard
driving
or prolonged idling in very hot weather will cause the pointer to move
beyond the center of the band. Should pcinter move to the line at the "H" end
of the band , see "Engine Cooling
System" on page 3-3.
Voltmeter
When the engine is operating, the voltmeter indicates the electrical system
voltage. During minimum electrical load, the pointer will read
to the right of the
center. As the electrical load is
increaSed, or in stop-and-go driving, the pointer
will rotate to the
left . A meter reading continuously in the left or right red zone
indicates an electrical system failure. Cause of the failure should be determined
and corrected.
Oil Pressure Gage
The oil pressure gage indicates the pressure at which oil is being delivered to
the various parts of the engine requiring lubrication. Pressures registered by the gage may vary according to outside air temperatures or weight of oil being
used. Oil pressure
of a cold engine being operated at a given speed will be
somewhat higher than when the engine is at normal operating temperature at
the same speed. Prolonged high speed operation on a hot day at the given
speed will result
in somewhat lower oil pressure readings. Readings of 205 to
275 kPa (30 to 40 psi) may be considered normal during moderate road
speeds of 35 to 40 mph (55 to 60 km/h) with the engine at proper operating
temperature . Gage readi'rig;rwhich are ·consistently high or low under these
conditions may indicate lubrication system and/or engine malfunction.
Windshield Wiper and Washer
The windshield wiping system operates at two speeds and is designed to wipe
clear
specijic areas of the windshield under most inclement weather conditions.
The windshield wipers work electrically and are not affected by engine
operation .
Push the control lever to the right to start
the electric windshield wiper. The
two-speed electric wiper has both a "low " and a "high " speed position .
2-19

Downloaded from www.Manualslib.com manuals search engine "the "TEMP" light comes on (or, if you have a 900lant temperature gage, the
gage needle goes into the warning zone) and your air conditioner is on, turn it
off.
If the "TEMP" light (or gage) comes on while you are stopped in traffic,
shift the transmission to
"N" (Neutral).
If the "TEMP" light doesn't go off (or the gage needle doesn't start to drop)
within a minute or two:
• Pull over to a safe Place ""d stop the vehicle. Set the parking brake and
shift to "P" (Park) 9r, with a manual transmission, shift to Neutral first, then
set the parking brake.
• DON'T TURN OFF THE ENGINE. INCREASE THE ENGINE SPEED until it
sounds like it's going about twice as fast as normal idle speed. Bring the
idle speed back to normal
after two or three minutes.
tfthe "TEMP" light still doesn't 90 off, (or the gage needle doesn't start to
drop),
NOW TURN OFF THE ENGINE and proceed as follows.
•
lift the engine hood. Look at the coolant level in the "see through" coolant
recovery tank. The coolant level. should be at or above the "Full Cold"
mark on the tank. If it looks like the coolant is boiling, wait until it stops
before proceeding. You should not need to remove the radiator cap to
check the coolant
level and. it can be dangerous if the coolant is still hot. See the following Caution.
CAUTION: To help avoid being burned:
"'-'''''''''i',",,;0-Fc:io'ffi)tcremoy'J~_ c;<)olant recovery tank cap if the coolant is boiling, and
• do not remove -the radiatorc:ap WhilethIit8ngine'-aUid:radiltor a,.Slili hot.
Scalding fluid and steamean be released under pressure it either cap is taken off too soon,
-;<
• If coolant level is low:
•
looklorleaks at the radiator hoses and connections, heater hoses and
connections,
r"diator,and water pump. See that the. fan belts are not
broken or off the pulleys an.d that the fan turns when the engine is started,
•
Add coolant to the recovery tahk.
If
the cQolant level in the recovery tank is althe correct lellel arid the "TEMP"
light (gage) still co"",s.dn,. air may be tr~ in the cooling system, This may
stop coolant from returning to the radiator. In this case, you may have to add
coolant directly to the radiator.
See "Coolant Replacement" under engine
cooling system
in "Service and Maintenance," Section 5 of this manual. Follow
steps 1 and 10. for the correct way to remove the radiator cap and add .coolant
to the radiator.
After the
"TEMP" light is out (or the gage needle is out of the warning zone),
resume driving at a reduced speed. Return to normal driving after about ten
minutes if the light does not come back
on (or the gage needle does not go
back into the warning zone).
3-4

Downloaded from www.Manualslib.com manuals search engine 4. If a ring forms after spot cleaning, clean the entire area IMMEDIATELY.
5. Follow specific instructions on cleaner labels.
Cleaning General Soilage Or Water Spots From Fabric-Type
Trim With Foam-Type
Clealler
GM Multi-Purpose Powdered Cleaner is excellent for this type of cleaning and
for cleaning panel sections where small cleaning rings may be left from spot
cleaning.
• Vacuum the area thoroughly to remove any loose dirt.
• ALWAYS clean a full trim assembly or complete trim section. Mask
surrounding trim along stitch or
welt lines.
• Mix Multi-Purpose Powdered Cleaner in strict accordance with directions on the container label. Mix in proportion for smaller quantities.
• USE SUDS ONLY ON A CLEAN SPONGE OR SOFT BRISTLE BRUSH. DO NOT SATURATE FABRIC OR .RUB IT HARSHLY WITH A BRUSH.
IMMEDIATELY AFTER CLEANING, WIPE OFF EXCESS SUDS WITH A
SLIGHTLY DAMP ABSORBENT TOWEL OR CLOTH.
• IMPORTANT -IMMEDIATELY AFTER WIPING, FORCE-DRY THE FABRIC WITH AN AIR HOSE, HEAT DRYER OR HEAT LAMP. (Use caution with
heat dryer or lamp to help prevent fabric damage.)
• When trim materials with a sheen or luster finish are dry, wipe fabric lightly with a soft, dry, clean cloth to restore its sheen or luster~
.. ~~.P~t CI~.aning Fabric-Type Trim With Solvent Type Cleaner
Bef~~~ t~yirlgtb'remove aspotQf stain from fabric, determine as accurately as you can the type and age of the spot or stain: Some spots or slains can be
removed with water or mild soap solution (see "Removal of Specific Stains").
Spots or stains should always be removed as soon as possible.
Some types of stains or sOilage,such as lipstick, inks and grease, are very
difficult (sometimes impossible) to completely remove. When cleaning this type
of stain·or soilage, be sure not· to enlarge thesoiled'area.
GM Fabric Cleaner (Solvent Type) is excellent for spot cleaning grease, oil, or
fat stains.
• Gently scrape excess stain from the trim material with a clean, DULL knife
or scraper.
USE VERY LlTILE CLEANER, light pressure and clean cloths
(preferably cheesecloth). Cleaning should start at the outside of the stain,
"FEATHERING" toward the center. Keep changing to a clean section of
the cloth.
• When you clean a stain from fabric, immediately dry the area with an air hose, heat dryer, or heat lamp to help prevent a cleaning ring. (Use caution
with heat dryer or lamp to prevent fabric damage).
• If a ring forms, immediately repeat the cleaning operation over a slightly
larger area with emphasis
on "FEATHERING" towards its center. If ring
remains, mask off surrounding trim sections and clean the entire affected
area with
GM Multi-Purpose Powdered Cleaner (as described under
"Cleaning General Soilage or Water Spots with Foam Type Cleaner").

Downloaded from www.Manualslib.com manuals search engine FUEL CAP
The fuel cap is.behind the. rear license plate.
NOTICE: tt you need: to repWce the fuel cap, use only a cap with these same features as specifie your dealer.
The fuel tank filler cap has a "screw-on ratcheting type" feature .
• _ To remove -rotate cap counterclockwise to clear the inside of the filler
neck. This will allow any residual pressure to escape .
_ To install -reverse this procedure and tighten cap securely until a
"ratcheting ". clicking sound is heard indicating cap is on properly.
CATALYTIC CONVERTER
.Ttle .cal;!ly:tic converter is an emission control device added to the exhaust system,' to reduce exhaust gas pollutants. The converter contains
a ceramic material coated with noble metal catalysts. To prevent contamination
of the catalysts , unleaded gasol;"" must be used . Unleaded gasoline also
reduces spark plug louling. exhaust system corrosion and engine oil
deterioration.
The catalytiC converter requires the use of unleaded gasoline. Using leaded gasoline wilt cause --the converter to lose its effectiveness as an
emission control device. Leaded gasoline will also damage the Computer
Command Control, system oxygen sensor, which could affect emission control,
fuel economy . and drivability.
~,~.,y..'~,","~ ... :..., To help 'prevent damage:
1. Keep your engine properly maintained . Engine malfunctions involving the electrical, carburetion or ignition systems may result in unusually high
catalytic con verter and exhaust . sy~tem temperatures which, under
extreme malfunctioning conditions·, may ignite interior floor:"'covering
materials above the converter. Do not keep driving your vehicle if you
detect engine misfire, noticeable loss of performance ,or other unusual operating conditions. Instead. have it serviced promptly.
A properly maintained
engine will help avoid malfunctions that could damage
the converter.
~ will also help provide good emission control and fuel economy.
See the Maintenance Schedule , folder for information on inspecling and
maintaining the engine. exhaust system. and other components. .
2. Do not drive through or Idle or park your vehicle over combustible
materials, such as grass or leaves_ They could touch the hot exhaust
system and ignite.
3. Do not push or tow this vehiCle to start it. This may result in unusually
high catalytic converter and exhaust system temperatures which under
extreme conditions may ignite interior floor -covering material above the
converter.
Pushing or towing to start can also damage · the catalytic
converter itself.
Disregarding these
instructions could damage the cataly:tic converter. the
vehicle, or nearby property.
5-2

Downloaded from www.Manualslib.com manuals search engine If you have to add coolant more than four times a year (either to the recovery
tank or to the radiator), see your dealer for a cooling system check.
NOTICE: If you use the proper quality antifreeze, there is no· need to add extra inhihitorsor additiveswtlich claim to improve-the system. They may be harmful to the proper operation of the system.
Cooling' System Service
The cooling system should be serviced at the intervals specified in Section A of
the Maintenance Schedule folder as follows:
1. Wash the radiator cap and filler neck with clean water. See step 1 of "Coolant Replacement" for the proper way to remove the radiator cap.
2. Check the coolant level in the radiator and have it tested for freeze
protection.
Add ethylene glycol antifreeze, if needed, to maintain freeze
protection at-3JOC (~$4°f).
3. Have the cooling system and radiator cap tested for a pressure capacity of 105. kPa (15psi). (The pressure cantle anywhere from 95 kPa, or 14 psi,
to 120
kPa, or 18 psi.) If a replacement cap is needed, use an AC cap, or
an equivalent cap, designed fof coolant recovery systems and specffied for
your model.
4. Tighten all radiator hose clamps ang heater hose clamps and inspect all
hoses. Replace the hOSes if they are swollen, "checked" or otherwise worn.
NOTICE: Take care when tightening the hose clamps at the radiator. Overtightening could bend or collapse the radiator fittings.
5. Clean the front of the radiator core and air conditioning condenser to
remove dirt and other objects. Also clean the auxiliary engine oil andlor
transmission fluid cooler if the vehicle has them.
Coolant Replacernent
At the intervals specffied in Section A of the Maintenance Schedule folder, flush
9r1d refill the cooling system as follows:
1. Remove the radiator cap when the engine is cool:
•
Turn the cap slowly to the left until it reaches a "stop." Do not press
down while turning the
cap.
• Wait until any remaining pressure (indicated by a hissing sound) is
relieved, then press down on the cap and continue turning it to the left.
CAUTION: To help avoid the dangarm being burned. donotrem_ove the radiator cap While the engine' and radiator are. still. hot. Scaldingftukland steam ean be blown out under ~re It the cap is taken off too SOOf1.
2. When the cap is removed, run the engine until the upper rad.iator hose is
hot.
(ThiS shows that th~ thermostat is open and the coolant is flowing
through the system.)
3. Stop the engine. Open Ihe,actialor drain valVE! to drain the coolant. Drainage may be speeded by removing the drain plugs in the block, ff so
equipped.
5-7

Downloaded from www.Manualslib.com manuals search engine 4. Close the drain valve. Install the block drain plugs, if removed. Add water
until the system is
filled and run the engine until the upper radiator hose is
hot
again.
5. Repeat steps 3 and 4 several times until the drained liquid is nearly colorless.
6. Drain the system, then close the radiator drain valve tightly. Install block
drain plugs, if removed.
7. Disconnect all hoses from the coolant recovery tank. Remove the recovery
tank
and pour out any fluid. Scrub and clean the inside of the recovery
tank with soap and water. Flush it well with clean water, then drain it.
Reinstall the recovery tank and hoses.
8. Add enough water and ethylene glycol antifreeze (meeting GM
Specification 1899-M) to provide the required cooling, freezing and
c()rrosion protection, Use a solution that is at least 50 percent antifreeze out no mOre than 70 percent antifreeze. Fill the radiator to the base of the
filler neck
and fill the coolant recovery tank to the "Full Hot" mark. Put the
recovery tank cap back on.
9. Run the engine, with the radiator cap removed, until the upper radiator
hose is hot.
10. With the engine idling, add coolant to the radiator until it reaches the
bottom of the filler neck. Install the radiator cap, making sure the arrows on the cap line up with the overflow tube.
iI is the owner's responsibility to,
'. -Main)!!!n cooling system freeze protection at -3rC (-34'F) to ensure protection against corrosion and loss of coolant from boiling. (A 50/50
mixture of water and ethylene glycol antifreeze will provide freeze
protection to -37'C or -34'F.) You should do this even if you don't
expect freezing temperatures.
• Add ethylene glycol base' antifreeze that meets GM Specification 1899-M
when antifreeze haS to be added because of coolant loss or for more
protection against freezing at temperatures lower than -37'C (-34'F).
NOTICE: Do "otute methanol-base antifreeze, Of alcohol,or plain water alone, in your vehicle at any time. They will boil at a lower point than that at which the "TEMP"
light (or temperature gage) will warn of overheating,. and they do not provide proper protection against cOrrosion.
Radiator Pressure Cap
The radiator cap, a 105 kPa (15 psi) pressure type, must be installed tightly,
otherwise coolant may be lost and damage to engine may result from
overheating. Radiator pressure
caps should be checked periodically for proper
operation. If replacement is required, an AC cap is recommended.
Thermostat
The engine coolant temperature is controlled by a thermostat. It stops coolant
flow
through the radiator until a preset temperature is reached. This thermostat
is installed in the engine
coolant outlet on the engine block. The same thermostat is used in both winter and summer. When a replacement is needed, AC"Delco parts are recommended.
5-8