1981 CHEVROLET MONTE CARLO transmission

Downloaded from www.Manualslib.com manuals search engine After acceleraUng to the desired speed and engaging the Cruise Control, the vehicle ' will no longer slow down when you take your foctot! the
accelerator pedal. TO slow the vehicle , disengage the Cruise Control by
depressing the brake pedal. '
When going up or down
hills (particularl~ when towing a trailer), it is possible for the vehicle to lose or gain speed, even though the Cruise Control is engaged,
If this happens while going up hill, merely depress the accelerator pedal temporarily to maintain the speed desired, If going down a hill steep
enough to cause the vehicle to gain speed, depress the brake pedal -­which will .\)Dth disengage the Cruise Control and help slow the vehicle, In addition, when going down a steep or long grade, the transmission should be placed in a lower .range or gear to help control vehicle speed --see the r~lated caution in the "Transmission" area. '
HORN
The horn on your vehicle is actuated by firmly pressing on the pad in th.e
center of the steering wheel. As a good motorist, use of ·the hOrn should be
kept at a minimum, However,
acquaint yourself as soon as possible with ihis
function of your
vehicle, should it ever become necessary to give a warning to
a pedestrian or another motorist
HAZARD WARNING FlASHER
The hazard flasher is covered on Page 3-' in the "In .Case of Emergency" section.
FLOOR CONTROLS
BRAKING SYSTEM
The regularbraking~yst"r1'lTsdesigned for braking performance under a wide
range of driving conditions even when the
vehicle is loaded to its full rated
vehicle load capacity .
CAUTION: DriVing ttvOUgh water deep enough to wet brake componenu-,may cause the brakes to ,n ,ot .work as well. A, • result the :vehicle will not slow: down at the usual rate,. and, it 'may pull 10 ,the .righ,t , 0.:' left. After chtc;king to the rear for other vehicles, apply the brakes 'lightly , to cheek whether this has happened. 1'0 dry them quicklY,lightly apply the-brakes.. At the aame. time, keep a safe forward speed, with plenty of cle._ space ahead, to the rea" and-to the sides;. Do this- until the brllkes return to norm.l.
Brake Warning Light
The brake system warning light is covered in the "Instrument Panel" section,
Power Brake$
• If power assist is ~Iost because of a stalled engine or other reasons , the
brakes can
normally still be applied with power assist at least" two times
using reserve power.
• The system is designed .to bring the vehicle to a full stop ·on reserve power
if
the brake pedal is applied once and held down. However, the reserve
power is partly used up each time the
brake pedal is applied and released , Do not pump the brakes when brake power assist has been lost; except
when needed to maintain steering control.
2-13

Downloaded from www.Manualslib.com manuals search engine "the "TEMP" light comes on (or, if you have a 900lant temperature gage, the
gage needle goes into the warning zone) and your air conditioner is on, turn it
off.
If the "TEMP" light (or gage) comes on while you are stopped in traffic,
shift the transmission to
"N" (Neutral).
If the "TEMP" light doesn't go off (or the gage needle doesn't start to drop)
within a minute or two:
• Pull over to a safe Place ""d stop the vehicle. Set the parking brake and
shift to "P" (Park) 9r, with a manual transmission, shift to Neutral first, then
set the parking brake.
• DON'T TURN OFF THE ENGINE. INCREASE THE ENGINE SPEED until it
sounds like it's going about twice as fast as normal idle speed. Bring the
idle speed back to normal
after two or three minutes.
tfthe "TEMP" light still doesn't 90 off, (or the gage needle doesn't start to
drop),
NOW TURN OFF THE ENGINE and proceed as follows.
•
lift the engine hood. Look at the coolant level in the "see through" coolant
recovery tank. The coolant level. should be at or above the "Full Cold"
mark on the tank. If it looks like the coolant is boiling, wait until it stops
before proceeding. You should not need to remove the radiator cap to
check the coolant
level and. it can be dangerous if the coolant is still hot. See the following Caution.
CAUTION: To help avoid being burned:
"'-'''''''''i',",,;0-Fc:io'ffi)tcremoy'J~_ c;<)olant recovery tank cap if the coolant is boiling, and
• do not remove -the radiatorc:ap WhilethIit8ngine'-aUid:radiltor a,.Slili hot.
Scalding fluid and steamean be released under pressure it either cap is taken off too soon,
-;<
• If coolant level is low:
•
looklorleaks at the radiator hoses and connections, heater hoses and
connections,
r"diator,and water pump. See that the. fan belts are not
broken or off the pulleys an.d that the fan turns when the engine is started,
•
Add coolant to the recovery tahk.
If
the cQolant level in the recovery tank is althe correct lellel arid the "TEMP"
light (gage) still co"",s.dn,. air may be tr~ in the cooling system, This may
stop coolant from returning to the radiator. In this case, you may have to add
coolant directly to the radiator.
See "Coolant Replacement" under engine
cooling system
in "Service and Maintenance," Section 5 of this manual. Follow
steps 1 and 10. for the correct way to remove the radiator cap and add .coolant
to the radiator.
After the
"TEMP" light is out (or the gage needle is out of the warning zone),
resume driving at a reduced speed. Return to normal driving after about ten
minutes if the light does not come back
on (or the gage needle does not go
back into the warning zone).
3-4

Downloaded from www.Manualslib.com manuals search engine 'I'
'"
JACKING INSTRUCTIONS OJ PARK ON A Lf;VEL SUR'ACE AND SET PARKING BRAKE FIRMLY, [!] SET_ AUTOMATIC TRANSMISSION IN "PARK" (MANUAL TRANSMISSION IN RIEVERH,_
...0 DO NOT TAa 'tOUI ~ THIOUGH ..... NJroMATtc CAl-WASH WIT" O)III#ACT WAIl INSTAU.ID . THI .... HtC&I' .... T OIl CAIIGHT WHICH COULD .I$UlT ... NONJn D.t.MAGI. .... _._ ...... __ ........ __ •• __ ._ .. II'>
AERO BACK COUPE MODELS Irutan Jack using Upper Hole Location.
LEVER IN DOWN POSITION
-~~ ... /~ ..
TIGHTEN
( " §. = .. :Mt .. : . 0 II .OZ
ill TURN_ON THE HAZARD W.ARNING FLASHER •. o REMOVE JACKING TOOLS AND PARE T IRE FROM STOWAGE. AREA. [!] aLOCK FRONT AND REAR OF WHEEL DIAGONALLY OPPOSITE WHEEL BEING REMOVED IIE"O .. I: OPERATING JACK. [!) LOOSEN, BUT DO NOT REM,OVe: WHEEL NUTS BV TURNING WRENCH COUNTIERCLQCI ~
' ' L.OAD PAO . N.UT.S IN A C IUSS·C ROSS SEQUENCII.Y TURNING WRENCH CLOCKWISE,. ---~ -~ACK RATCHET MECHANISM SHOULD.II OILED AFTER EACH USE.
"RAMII~~
JACK

Downloaded from www.Manualslib.com manuals search engine Towing
Proper equipment .must be used to prevent damage to vehicles during any
towing. State (Provincial in Canada) and local laws which apply to vehicles in
tow must be
followed. Get detailed towing instructions from your dealer.
Your vehicle
may be towed on all four wheels, at speeds less than 35 mph (60
km/h), for distances up to 50 miles (80 kilometers), provided the driveline and
steering are normally operable. For such towing, the steering must be unlocked, transmission in neutral and the· parking brake released. Connect to
main structural parts of the vehicle. Do NOT attach to bumpers or brackets.
Remember also that power assist for brakes and steering will not be available when the engine is off.
If the vehicle is to be towed by a wrecker, use only equipment designed for this purpose, following the instructions of the wrecker manufacturer. A safety Chain
system must be used for all towing.
FREEING VEHICLE FROM SAND, MUD, SNOW OR
ICE
If your vehicle gets stuck in sand, mud, snow or ice, move the shift lever on automatic transmission models from "0" (Drive) to "R" (Reverse) in a repeat
pattern.
Apply a light pressure to the accelerator pedal while the transmission is in gear. Remove your foot from the accelerator while shifting. Do not race
the engine. For best traction, avoid spinning the wheels. Incorrect rocking of your vehicle while it is stuck may result in damage to vehicle components.
CAUTION: Do not spin the wheels faster than 35 mph (55 km/h). Personal injury and
damage (inCluding tire, transmission and/or rear axle failure) may result from excessive
wheel spinning.
If the vehicle remains stuck after several rocking attempts, seek other
assistance. Also see the Notice under '(Automatic Transmissions" in "Steering
Column-Controls," Section 2 of this manual.
3-9

Downloaded from www.Manualslib.com manuals search engine PART NUMBER
1051516
1050017
1052277
1050172
1050173
1050174
1050214
f' 1050237 .... 1050244
1052280
1050427 1050429
1052349
1050729
1051055
1051398
1051515 1051172 1051855 1051858
1052103
1052271 1052272
APPEARANCE CARE AND MAINTENANCE MATERIALS
SIZE DESCRIPTION
32 02. 10.946 U Washer -Solvent and Gas Line De-Icer 3 '2 oz, (0.946 LI Power Steering Fluid 16 oz. (0.473 LI Spray-A-Sq ueak
16 oz. (0.473 L) Tar and Road Oil Remove'r 16 oz . (0.473 L) Chrome Cleaner and Polish 1602.10,473 LI WhiteSidewall Tire Cleaner , 32 oz. 10.946 L) Vinyl/Leather Cleaner 16 oz. 10.473 L) Finish Guard Cleaner 16 oz. (0.473 L) Fabric Cleaner 1'2 oz. 10.354 L) Heat Valve Lubricant 23 oz. (0.680 L) Glass Cleaner 6 lb. 12.72 kg) Multi·Purpose Powdered Cleaner
16 oz. (0.453 kg) Lubriplate (White Grease) 8 oz. 10.237 Ll Vinyl Top Cleaner 16 oz. (0.473 LI Preservatone 8 oz. 10.237 L) Spot Lifter 32 oz, 10.946 LI GM Optikleen 20 oz . (0.567 kg) presofl®ed-Cleaner/wax 32 oz. 10.946 U Dexron II 16 oz. (0.473 1I GM Engine Oil Supplement (E.O.sJ 1 gal. 13.785 L) Anti·Free ze Coolant lethylene glycol base) 23 oz. 10.680 L ) GM Gear Lubricant 15 gal. (60 L) GM Gear Lubricant
USAGE
Washer Solvent and gas line Oe-icer Power Steering Weather Strips -stops squeaks on metal-to-metal and metal-to~ rubber contact Removes old waxes, polishes, tar, and road oil Removes rust and corrosion on chrome and stainless steel
Cleans white imd black tires Spot and stain removal on leather or vil'lyl One step cleaner and wax and aluminum· wheels Spot and stain removal on cloth and fabric Free up sticky heat ri;ers -general purpose penetrant Glasscleaning and spot cleaning on vinyls
Cleans vinyl and cloth on door trim, seats, and carpet-also, tires and mats Grease for hood, trunk and door hinges and latches
Cleaning of vinyl tops Viny l Top Dressing SPOt and stain removal on cloth and fabric
W indshield washer solvent and anti-freeze One step c leaner/wax Automatic transmission Consult your Dealer for specific usage
Year round coolant and anti-freeze Rear axle lubricant Same as 1052271

Downloaded from www.Manualslib.com manuals search engine un mUE SAl: VIScOSITY GRADES
F~O 20 40 60 100 C -30 -20 10 0 10 20 30 40 TEMPERATURE RANGE YOU .EXPECT SHORE NEXT Oil CHANGE
NOTICe: DO NOTUSE SAE 5W-2(I OILS fOR COIfi"INUOUS HIGH SPEED DRIVING.
Engine Oil Additives
There are many extra engine oil additives (or helpers) for sale. Your engine
should not need these extra additives if you Use SF-quality engine oil and
change it as suggested. If you think your engine has an oil-related problem,
talk
to your authorized dealer. If needed, your dealer can provide you with a
tested and approved oil additive called "GM Engine Oil Supplement."
AUTOMATIC TRANSMISSION FLUID RECOMMENDATIONS
Proper Fluid -Use only automatic transmission fluid labeled DEXRON® II. You
can buy this fluid from your dealer or other service outlets.
Checking
Fluid Level-Check the automatic transmission fluid level at each
engine
oil change, Overfilling GaI).c"!,J~e foaming and loss of fluid. A low fluid
level can cause slipping or loss of drive. In either case, transmission damage
can result.
To check the fluid
level, first set the parking brake, then start the engine in "P"(Park). With the regular brakes applied, move the shift lever through all the
gear ranges, ending
in "P". You must check the fluid level with the engine
running
at slow idle and the vehicle level.
You cannot read the correct fluid level if you have just.driven you(vehicle fora
long time at high speed, in city traffic in hot weather, or if your vehicle has
been
pulling a trailer. Wait until the fluid cools down (about 30 minutes).
Remove the dipstick
located at the rear of the engine compartment on the
passenger's side. Carefully touch the wet end of the dipstick to find out if the
fluid
is cool, warm or hot. Wipe it clean and push it back in until the cap seats. Pull out the dipstick and read the fluid level.
• If
it felt cool (about room temperature), the level should be 3 to 10
millimeters (118 to 3/8 inch) below the "Add" mark. The dipstick has two
dimples below the" Add" mark to show this range.
• If it felt warm, the level should be close to \he "Add" mark (either above or below).
• If
it was too hot to hold, the level should be at the "Full" mark.
5-5

Downloaded from www.Manualslib.com manuals search engine COOL
WARM
Add just enough DEXRO~ II fluid to fill the transmission to the proper level. It
takes only 0.5 liter (one pint) to raise the level from "Add" to "Full" with a hot
transmission.
Automatic Transmission Drain Intervals
Change the transmission fluid and change the filter (or clean the screen) as
outlined
in Section A of the Maintenance Schedule folder.
ENGINE COOLING SYSTEM
Your vehicle has a coolant recovery system. Coolant in the system expands
with heat and overflows into the recovery tank. When the system cools down,
coolant is drawn back into the radiator.
The cooling system was
filled at the factory wrth a quality coolant that meets
GM
Spec~ication 1S99-M . The cooling ·system is designed to use coolant (a
mixture of water and ethylene glycol antifreeze) rather than plain water. The
coolant solution should be used year round.
It has many advantages, such as:
~ provides freezing protection down to -3rC (-34"F) "''''''<~. !'"","."" ' • provides boiling protection up to 12S"C (262"F),
• protects against rust and corrosio~in th~ cooling system,
• maintains the proper engine temperature for efficient operation and
emission control, and
• allows proper operation of the coolant temperature light or gage :
See Section A of the Maintenance Schedule folder to find out when the coolant
must
be ·replaced.
Cooling System Care
Check the c60ling system at regular intervals, such as during fuel stops . You usually do not need to remove the radiator cap to check the coolant level. Lift
the engine hood and look at the "see through" coolant recovery tank. When
the engine is
cold, the coolant level should be at the "Full Cold" mark on the
tank . When the engine has fully warmed . up, the level should be above the
"Full Cold" mark on the tank . If the coolantl6vel is low, remove the cap on the
coolant recovery tank. Add to the recovery tank enough of a 50/50 mixture of
water and a good quality ethylene glycol antifreeze to bring the
level up to the
proper mark. Put the cap back on the recovery tank.
Certain conditions, such
as air trapped in the system, may affect the coolant
level in the radiator. You should check"the coolant level in the radiator at the
time you change the engine
oil and when the engine Is cold. Follow.taps I, S,
9, and 10 under "Coolant Repfacement" for the correct way to remove the
radiator cap and add coolant.
5-6

Downloaded from www.Manualslib.com manuals search engine If you have to add coolant more than four times a year (either to the recovery
tank or to the radiator), see your dealer for a cooling system check.
NOTICE: If you use the proper quality antifreeze, there is no· need to add extra inhihitorsor additiveswtlich claim to improve-the system. They may be harmful to the proper operation of the system.
Cooling' System Service
The cooling system should be serviced at the intervals specified in Section A of
the Maintenance Schedule folder as follows:
1. Wash the radiator cap and filler neck with clean water. See step 1 of "Coolant Replacement" for the proper way to remove the radiator cap.
2. Check the coolant level in the radiator and have it tested for freeze
protection.
Add ethylene glycol antifreeze, if needed, to maintain freeze
protection at-3JOC (~$4°f).
3. Have the cooling system and radiator cap tested for a pressure capacity of 105. kPa (15psi). (The pressure cantle anywhere from 95 kPa, or 14 psi,
to 120
kPa, or 18 psi.) If a replacement cap is needed, use an AC cap, or
an equivalent cap, designed fof coolant recovery systems and specffied for
your model.
4. Tighten all radiator hose clamps ang heater hose clamps and inspect all
hoses. Replace the hOSes if they are swollen, "checked" or otherwise worn.
NOTICE: Take care when tightening the hose clamps at the radiator. Overtightening could bend or collapse the radiator fittings.
5. Clean the front of the radiator core and air conditioning condenser to
remove dirt and other objects. Also clean the auxiliary engine oil andlor
transmission fluid cooler if the vehicle has them.
Coolant Replacernent
At the intervals specffied in Section A of the Maintenance Schedule folder, flush
9r1d refill the cooling system as follows:
1. Remove the radiator cap when the engine is cool:
•
Turn the cap slowly to the left until it reaches a "stop." Do not press
down while turning the
cap.
• Wait until any remaining pressure (indicated by a hissing sound) is
relieved, then press down on the cap and continue turning it to the left.
CAUTION: To help avoid the dangarm being burned. donotrem_ove the radiator cap While the engine' and radiator are. still. hot. Scaldingftukland steam ean be blown out under ~re It the cap is taken off too SOOf1.
2. When the cap is removed, run the engine until the upper rad.iator hose is
hot.
(ThiS shows that th~ thermostat is open and the coolant is flowing
through the system.)
3. Stop the engine. Open Ihe,actialor drain valVE! to drain the coolant. Drainage may be speeded by removing the drain plugs in the block, ff so
equipped.
5-7