1981 CHEVROLET MONTE CARLO oil level

Downloaded from www.Manualslib.com manuals search engine FUEL REQUIREMENTS
Your engine is designed to use only unleaded gasoline . Unleaded gasoline must be uSed for the emission control system to operate properly . Its use will
also reduce spark
plug fouling, exhaust .system corrosion and engine oil deterioration.
Using
leaded gaso~ne can damage the emission control system and could
result
in loss of warranty coverage. The effectiveness of the catalyst in the
catalytic converter decreases after use of as little as one tank of leaded
gasoline.
Also, your vehicle may have the "Computer Command Control" system, which includes an oxygen sensor. Leaded gasoline will damage the
sensor,
and attect emissioncont(ols. (For more information, see "Computer
Command Control
System" in "Service and Maintenance,"Section 5 of this manual. Federal regulations require that pumps delivering unleaded-gasoline
be labeled with the word UNLEADED. Only these pumps have nozzles whichftl the filler neck of your vehicle's gasoline tank.
In the United States, Federal law also requires that gasoline octane ratings be
posted on the pumps. The octane rating shown is an average of Research
octane (R) and Moto< octane (M). In most parts of the United States , you
should use unleaded gasoline with an octane rating of at least 87. However,
you may use unleaded gasoline with an Q!;tane rating as low as 85 in these
. high -altitude areas: Coloraclo , Montana, New Mexico , Utah , Wyoming,
northeastern Nevada, southern Idaho, western South Dakota, and that part of
Texas which is directly south of New Mexico .
Using unleaded gasoline with
an octane rating lower than stated above can
cause persistent, heavy
"spark knock." (" Spark knock" is a metallic rapping
noise.) " severe, this can
lead to engine darnage. " you detect heavy spark knock even ",hery using gasoline of the stated octane rating, 0<. if you hear steady spark knoo~ 'wfiil.)' Holding a' steady speed on level roads, have your
dealer correct the
problem . Failure to take steps to stop such knocking is
misuse
of the vehicle, for which Chevrolet is not responsible . However, now and then you may notice light spark knock for a short time while accelerating
or driving
up hills : This is no cause fo< concern, because you get the greatest
fuel economy
benem from the gasoline's octane rating when there is
occasional light spark knock. Using .gasoline with a higher .octane rating than
that which
allows occasional spark knock is an unnecessary expense.
Gasohol
Gasohol, a mixture of unleaded gasoline and ethanol (grain alcohol), is
available in some areas , You may use gasohol in yourvehicle ,provided it is no
more than 10% ethanoL Be sure the gasohol has octane ratings no lower than
those stated above for unleaded
gasoline . Some vehicles using gasohol could run leaner . Most drivers will not notice a difference, but some may. In such
cases your authorized dealer can make c.ertain adjustments, provided they are
not in violation of the Federal
Clean Air Act. " you. are still not satisfied with gaSOhol performance , you may prefer to uSe unleaded gasoline. •
NOTICE: ,Take care to not spiH gasohol on painted surfaces. Gasohol can cause paint damage, which may not be covered und~r the new vehicle warranty.
2·3

Downloaded from www.Manualslib.com manuals search engine Pressing the control will send waier' or 'other cleaning agent onto the
wlildshield until control is released and will also cause the wiper lever to move
thus starting the wiper mOtOL The wiper will continue to operate until manually
turned off at the wiper
control lever.
Fill the washer jar only 3/4 full during the winter to allow for expanson iI the
temperature
should fall low enough to freeze the solution.
• Check the washer fluid level regularly. Do it ofIen when the weattier . is bad.
• Use a fluid such as GM Optikleen to help prevent freezing damage, and for
better cleaning . Be sure to put the fluid in the proper reservoiL
• Do not use radiator antifreeze in the windshield washer; it could cause
paint damage.
• In cQld weather, warm the windshield with the defrosters before using the wesher--to help prevent Icing that may block the driver's vision.
Delay Wiper System
If equipped with this optional feature the wipers may be operated in anyone of
four positions;
DELAY , LO, HIGH or MIST . The Delay position provides
intermittent wiper operation during periods of light rain, mist or fog when
continuous Wiping.
is unnecessary . The 'Mist feallJe provides momentary low
speed wiper operation when needed .
The
Delay feature is actuated by sliding the wiper control knob to the first pOsition to the right of "OFF" .. The amount of delay between wipes is controlled by rotating the control knob .
.• , Maximum delay (slowest wiper speed) is obtained by rotating the control " .. ",. 'l •
The delay interval decreases (increased wiper speed) as the control knob is rotated clockwise. Full clockwise rotation will allow the wipers to operate as if in Low speed.
• The delay feature may be actuated and adjusted for delay cycling at any
time. However , the delay feature will be canceled, ij the control knob is
placed in Low or High speed positions,
MIST OFF DELAY LOW HIGH
Low speed is obtained by sliding the control knob to the second position to the right.
High speed is obtained by sliding the control knob to the extreme right position.
2-20

Downloaded from www.Manualslib.com manuals search engine • Always wear eye protection or shiekI your eyet when ,workmg .....,. My battery. Do not lean over a, battery. Remove .11 met.1 jewelry.
• Never expose .-battery to open fIanea eM' e~ sparb. -AlIa. do no( smoke near a battery.
• 00 not .llow battery acid to c:ontact eyes._IIdn. f~or painted autfaces. FLUSH ANY CONTACTED ARE"WlTH W"TER '_OtATELY AND THOIlOUGHLY. GET MEDICAL HELP IF EYES ARE AFFECTED.
• Be sure ' the Jumper cabie. or clampt to be used for jump starting do not have lOose or missing insulation. Do not prPCeed if $Uitable c.bae. .... not avanable. "
• Thi" vehicle has • 12-volt. batt.ry and a _ negative ground electrical .ystem. Make sure that -the other vehkte abo ha. a 12-vott battery .nd that tt .. the negative (~k II";"''') terminal which i. grounded (anached to the engine btoc:k). Hs owner's manual may give you that information. 00 NOT TRY TO JUMP START IF YOU ARE UNSURE OF THE OTHER VEHICLES VOl.TAGE ORGROOND (OR F THE OTHER VEHICLE'S VOLTAGE AND/OR Gr:tOUND ARE DIFFERENT FROM YOUR VEHICLE).
e. • eithel t'latIetY has flUer c:ap', check the flukt -leveL (Do _ no( cheek wlUl an open ta.M.> If lOw, flll'tO-ttle proper leVel with cia.,. drinking water. Replace aU c:aps before jump atarting.
e Do not allow metal tools to contact both the positive (red "+ ") battMy tennil\al (or any metal connected to thl. tenninal) and .ny other metal on either vehicle at the -same -tIme. ",.ke c:ertillin when .ftaching th6 Jumper c.~ elamps to the positive terminals Of the batteriet: _that neither clamp contacts. MY other metal •
• ' Alway. make the final ~o-"nectlon to' ground, (a adlid, .tatlon.ty, metallic object) on the engine at '~ast4SO 'millimeter. (18 Inches) from the battery.
Procedure ~~~i~._ 1. posill oW\he ·,verncJe with the good (cnarged) .!>allery so that the jumper cables will reach. Do not let th'1vehiclestouch ..
2. Turn off all elec .ltic motors, lights and accessories in both vehicles, except
the hazard flasher or any light~ need!ld for the work area. Turn ott the
ignition ,. apply the perkingbiilke' fi'rmly, and· shift the automatic
tr.ansmission to
"P"(Park) in both vehicles.
3. Jum~r Cable Connj!ction Instructions (See Illustration).
• Connecflhe
first jurnpercable to the positive " +" (red) terminal on
one battery, and. then to the positive" +" (red) terminal on the other
battery .
Never conlledt " +" (redl,to "-" (black), or "-" to " + ".
• Next, COnnect one endot theseC(jnd cable to the grounded negative "-"(black) terminal of the good (charged) battery.
• Lastly. c<;>nnect the other end· of the second jumP'l' cable to ground at least 450 millimeters (18 inches) from the discharged battery, to a solid, stationery, metallic object on the engine. Do not route the cable,
or
attach the clamp on or near pulleys, fans, or other parts that will
move when the engine is started , Be careful to noUouch hot engine
parts
as they can cause burns. The MOUNTING BRACKETS for the Delcotron (generator), or the ainlOnditioner compressor, generally
make a good point for this final ground attachment, ~ hot· or moving
parts c"" be avoided.
3-2

Downloaded from www.Manualslib.com manuals search engine "the "TEMP" light comes on (or, if you have a 900lant temperature gage, the
gage needle goes into the warning zone) and your air conditioner is on, turn it
off.
If the "TEMP" light (or gage) comes on while you are stopped in traffic,
shift the transmission to
"N" (Neutral).
If the "TEMP" light doesn't go off (or the gage needle doesn't start to drop)
within a minute or two:
• Pull over to a safe Place ""d stop the vehicle. Set the parking brake and
shift to "P" (Park) 9r, with a manual transmission, shift to Neutral first, then
set the parking brake.
• DON'T TURN OFF THE ENGINE. INCREASE THE ENGINE SPEED until it
sounds like it's going about twice as fast as normal idle speed. Bring the
idle speed back to normal
after two or three minutes.
tfthe "TEMP" light still doesn't 90 off, (or the gage needle doesn't start to
drop),
NOW TURN OFF THE ENGINE and proceed as follows.
•
lift the engine hood. Look at the coolant level in the "see through" coolant
recovery tank. The coolant level. should be at or above the "Full Cold"
mark on the tank. If it looks like the coolant is boiling, wait until it stops
before proceeding. You should not need to remove the radiator cap to
check the coolant
level and. it can be dangerous if the coolant is still hot. See the following Caution.
CAUTION: To help avoid being burned:
"'-'''''''''i',",,;0-Fc:io'ffi)tcremoy'J~_ c;<)olant recovery tank cap if the coolant is boiling, and
• do not remove -the radiatorc:ap WhilethIit8ngine'-aUid:radiltor a,.Slili hot.
Scalding fluid and steamean be released under pressure it either cap is taken off too soon,
-;<
• If coolant level is low:
•
looklorleaks at the radiator hoses and connections, heater hoses and
connections,
r"diator,and water pump. See that the. fan belts are not
broken or off the pulleys an.d that the fan turns when the engine is started,
•
Add coolant to the recovery tahk.
If
the cQolant level in the recovery tank is althe correct lellel arid the "TEMP"
light (gage) still co"",s.dn,. air may be tr~ in the cooling system, This may
stop coolant from returning to the radiator. In this case, you may have to add
coolant directly to the radiator.
See "Coolant Replacement" under engine
cooling system
in "Service and Maintenance," Section 5 of this manual. Follow
steps 1 and 10. for the correct way to remove the radiator cap and add .coolant
to the radiator.
After the
"TEMP" light is out (or the gage needle is out of the warning zone),
resume driving at a reduced speed. Return to normal driving after about ten
minutes if the light does not come back
on (or the gage needle does not go
back into the warning zone).
3-4

Downloaded from www.Manualslib.com manuals search engine COMPUTER COMMAND CONTROL SYSTEM
Your new vehicle has a special emission contrOl system, called the Computer
Command Control system. Some vehicleS sold in Canada also have the
Computer Command Control system. II your Canadian vehicle has a "CHECK
ENGINE" light,
it dOes have the Computer Command Control system.)
The Computer Command Control system monitors . the .exhaust stream with
an
oxygen sensor. Based on sensor signals, the electronic control module adjusts
the carburetor air-fuel ratio as needed. It is very important to use only
unleaded gasoline in vehicles equipped with the Computer COmmand Control
system . .Leaded gasoline will damage the oxygen sensor and may affect
. emission controL .
On
all vehicles with the COmpute r Command Control system, a "CHECK
ENGINE" ligtit
on the instrument panel is designed to come on during engine
starting, to
let you knowthe bulb .is working. (The light will stay on a'shdl1iime
after the. engine starts.) If. the light comes on while driving, service to the
Computer Command Control system may be. required. Although your vehicle
may
still be drivable,see yoyr dealer as SOon as possible for an inspection of
the system.
Continued
driving · Without having the Computer Command Control system
serviced could cause damage to the emiSsion control system. It could also aftect fuel economy and drivability. .. ..
ENGINE OIL AND FILTER RECOMMENDATIONS
Checking 011 Level ,>,-.. ,
The engine oil must be kept at the right level to. help assure proper lubrication
of your vehicle' .s engine.
It is the owner's responsibility to' cheCk the oil level at
regular': infervals '{such . 'as . "e~~Y"JHflLstop), according ·to ' the following instruct ions . It is normal for an engine-O to use Some oil, and most engines may
use
more oil when they are new . " .
• The best time to check' the engine Orffevel is when the oil IS warm, such as
during a
fuel stop. First, wait about 5 minutes for the oil to drain back to the oil pan. Then, pull out the dipstick on the side of the engine block (either
right or left). Wipe
it clean and. push the dipstick back down all the way.
Now,
pull out the dipstick and look at the oil level .on the dipstick.
Some dipsticks have "Add" and "Full" lines. Others are marked "Add lOt"
and "OperatlngRange ." In all cases, keep the oil level above the "Add" line_ Push the dipstick .oock down alilheway after taking the reading . Add oil , if needed . . .
• If you check the oil level when the oil is cold, do not iun the engine first.
The
cold oil will not drain back to the pan fast enough to give a tr ue oil
level. . .
Ch '
oosing the Right Quality on
Engine oils are labeled on'the containers with variOus API (Amercian Petroleum Institute) deSignations of·quality. Artewhigher-quality category of engine 011,
designation "SF", was introduced early in 1980. Be sure the oil you use has
the
API designation "SF," either alone or shown with other designations . Do not use oils labeled only SA, SB,SC, SO,' SE, CA, CB,CC, or CD; or oils
with a combination of any of these categories-like SE/CD.
5-3

Downloaded from www.Manualslib.com manuals search engine un mUE SAl: VIScOSITY GRADES
F~O 20 40 60 100 C -30 -20 10 0 10 20 30 40 TEMPERATURE RANGE YOU .EXPECT SHORE NEXT Oil CHANGE
NOTICe: DO NOTUSE SAE 5W-2(I OILS fOR COIfi"INUOUS HIGH SPEED DRIVING.
Engine Oil Additives
There are many extra engine oil additives (or helpers) for sale. Your engine
should not need these extra additives if you Use SF-quality engine oil and
change it as suggested. If you think your engine has an oil-related problem,
talk
to your authorized dealer. If needed, your dealer can provide you with a
tested and approved oil additive called "GM Engine Oil Supplement."
AUTOMATIC TRANSMISSION FLUID RECOMMENDATIONS
Proper Fluid -Use only automatic transmission fluid labeled DEXRON® II. You
can buy this fluid from your dealer or other service outlets.
Checking
Fluid Level-Check the automatic transmission fluid level at each
engine
oil change, Overfilling GaI).c"!,J~e foaming and loss of fluid. A low fluid
level can cause slipping or loss of drive. In either case, transmission damage
can result.
To check the fluid
level, first set the parking brake, then start the engine in "P"(Park). With the regular brakes applied, move the shift lever through all the
gear ranges, ending
in "P". You must check the fluid level with the engine
running
at slow idle and the vehicle level.
You cannot read the correct fluid level if you have just.driven you(vehicle fora
long time at high speed, in city traffic in hot weather, or if your vehicle has
been
pulling a trailer. Wait until the fluid cools down (about 30 minutes).
Remove the dipstick
located at the rear of the engine compartment on the
passenger's side. Carefully touch the wet end of the dipstick to find out if the
fluid
is cool, warm or hot. Wipe it clean and push it back in until the cap seats. Pull out the dipstick and read the fluid level.
• If
it felt cool (about room temperature), the level should be 3 to 10
millimeters (118 to 3/8 inch) below the "Add" mark. The dipstick has two
dimples below the" Add" mark to show this range.
• If it felt warm, the level should be close to \he "Add" mark (either above or below).
• If
it was too hot to hold, the level should be at the "Full" mark.
5-5

Downloaded from www.Manualslib.com manuals search engine COOL
WARM
Add just enough DEXRO~ II fluid to fill the transmission to the proper level. It
takes only 0.5 liter (one pint) to raise the level from "Add" to "Full" with a hot
transmission.
Automatic Transmission Drain Intervals
Change the transmission fluid and change the filter (or clean the screen) as
outlined
in Section A of the Maintenance Schedule folder.
ENGINE COOLING SYSTEM
Your vehicle has a coolant recovery system. Coolant in the system expands
with heat and overflows into the recovery tank. When the system cools down,
coolant is drawn back into the radiator.
The cooling system was
filled at the factory wrth a quality coolant that meets
GM
Spec~ication 1S99-M . The cooling ·system is designed to use coolant (a
mixture of water and ethylene glycol antifreeze) rather than plain water. The
coolant solution should be used year round.
It has many advantages, such as:
~ provides freezing protection down to -3rC (-34"F) "''''''<~. !'"","."" ' • provides boiling protection up to 12S"C (262"F),
• protects against rust and corrosio~in th~ cooling system,
• maintains the proper engine temperature for efficient operation and
emission control, and
• allows proper operation of the coolant temperature light or gage :
See Section A of the Maintenance Schedule folder to find out when the coolant
must
be ·replaced.
Cooling System Care
Check the c60ling system at regular intervals, such as during fuel stops . You usually do not need to remove the radiator cap to check the coolant level. Lift
the engine hood and look at the "see through" coolant recovery tank. When
the engine is
cold, the coolant level should be at the "Full Cold" mark on the
tank . When the engine has fully warmed . up, the level should be above the
"Full Cold" mark on the tank . If the coolantl6vel is low, remove the cap on the
coolant recovery tank. Add to the recovery tank enough of a 50/50 mixture of
water and a good quality ethylene glycol antifreeze to bring the
level up to the
proper mark. Put the cap back on the recovery tank.
Certain conditions, such
as air trapped in the system, may affect the coolant
level in the radiator. You should check"the coolant level in the radiator at the
time you change the engine
oil and when the engine Is cold. Follow.taps I, S,
9, and 10 under "Coolant Repfacement" for the correct way to remove the
radiator cap and add coolant.
5-6

Downloaded from www.Manualslib.com manuals search engine If you have to add coolant more than four times a year (either to the recovery
tank or to the radiator), see your dealer for a cooling system check.
NOTICE: If you use the proper quality antifreeze, there is no· need to add extra inhihitorsor additiveswtlich claim to improve-the system. They may be harmful to the proper operation of the system.
Cooling' System Service
The cooling system should be serviced at the intervals specified in Section A of
the Maintenance Schedule folder as follows:
1. Wash the radiator cap and filler neck with clean water. See step 1 of "Coolant Replacement" for the proper way to remove the radiator cap.
2. Check the coolant level in the radiator and have it tested for freeze
protection.
Add ethylene glycol antifreeze, if needed, to maintain freeze
protection at-3JOC (~$4°f).
3. Have the cooling system and radiator cap tested for a pressure capacity of 105. kPa (15psi). (The pressure cantle anywhere from 95 kPa, or 14 psi,
to 120
kPa, or 18 psi.) If a replacement cap is needed, use an AC cap, or
an equivalent cap, designed fof coolant recovery systems and specffied for
your model.
4. Tighten all radiator hose clamps ang heater hose clamps and inspect all
hoses. Replace the hOSes if they are swollen, "checked" or otherwise worn.
NOTICE: Take care when tightening the hose clamps at the radiator. Overtightening could bend or collapse the radiator fittings.
5. Clean the front of the radiator core and air conditioning condenser to
remove dirt and other objects. Also clean the auxiliary engine oil andlor
transmission fluid cooler if the vehicle has them.
Coolant Replacernent
At the intervals specffied in Section A of the Maintenance Schedule folder, flush
9r1d refill the cooling system as follows:
1. Remove the radiator cap when the engine is cool:
•
Turn the cap slowly to the left until it reaches a "stop." Do not press
down while turning the
cap.
• Wait until any remaining pressure (indicated by a hissing sound) is
relieved, then press down on the cap and continue turning it to the left.
CAUTION: To help avoid the dangarm being burned. donotrem_ove the radiator cap While the engine' and radiator are. still. hot. Scaldingftukland steam ean be blown out under ~re It the cap is taken off too SOOf1.
2. When the cap is removed, run the engine until the upper rad.iator hose is
hot.
(ThiS shows that th~ thermostat is open and the coolant is flowing
through the system.)
3. Stop the engine. Open Ihe,actialor drain valVE! to drain the coolant. Drainage may be speeded by removing the drain plugs in the block, ff so
equipped.
5-7