CRUISE CONTROL SYSTEM TESTS
(ELECTRIC ACTUATOR)
Use BMW Service Test 2013 to check function of system
as follows:
Program: Enter M (Multimeter)
Enter 13 (Frequency out)
Enter 110 (Hz)
Press
Enter 02 (U. AC.)
Press
1. Detach the differential reed switch plug and attach frequency
out (+) to brown/red wire and frequency out (-) to brown
wire.
2. Turn on ignition.
3. Speedometer should show approximately 50 mph.
4. Engage cruise control and monitor the actuator. (It should
pull the throttle open.)
5. If cruise control does not engage, check for A.C. voltage on
E.C.U. plug terminal #6. (It should be approximately 4.0
volts.)
6. Check plug connections on back of instrument cluster.
7. If system is still inactive, perform the following tests:
Test at ECU Plug
Component/Circuit
Result
1. Ignition on—check volt-
age at Terminal #1.
Power supply
12 Volts. If not, check
wiring and fuse.
2. Ignition on—check volt-
age at Terminal #2.
Control switch OFF
Move lever to OFF. Voltage
drops from 12V to 0V. If
not, check wiring and
switch.
3. Ignition on—check volt-
age at Terminal #4.
Control switch CONST.
Move lever to CONST.
Voltage jumps 0 to 12V.
If not, check wiring and
switch.
61-09/2
FOR CRUISE CONTROL TO BE ENGAGED
PIN 9 MUST SENSE GROUND THROUGH
STOPLIGHTS.
WHEN BRAKE SWITCH IS CLOSED OR
CLUTCH SWITCH IS OPEN, GROUND IS
ELECTRONICALLY REMOVED.
CRUISE CONTROL ELECTRICAL SCHEMATIC
BRAKE
SWITCH
CLOSED WITH BRAKE
PEDAL DEPRESSED
POWER
DISTRIBUTION
BOX
CLUTCH
SWITCH
OPENS WHEN
CLUTCH PEDAL
IS DEPRESSED
POWER
DISTRIBUTION
BOX
AUTOMATIC
TRANSMISSION
RANGE SWITCH
AUTOMATIC TRANSMISSION
CRUISE
CONTROL
SWITCH
C210
CRUISE CONTROL
CONTROL UNIT
TRANSMISSION
RANGE
DISPLAY
TO THROTTLE
VALVE
FEEDBACK
POTENTIOMETER
INSTRUMENT
CLUSTER
CRUISE
CONTROL
ACTUATOR
CLUTCH
SOLENOID
CANCEL RESUME ACCELERATE/
SPEED SET SPEED
CONTROL INPUTS
INSTRUMENT
CLUSTER
MANUAL
TRANSMISSION
IDLE
SPEED
CONTROL
FUSE 6
8 AMP
POWER
DISTRIBUTION
POWER
DISTRIBUTION
ACCELERATE/
SET
OFF RESUME
OFF
S217 C206 S309 C301
.75 GN/WT
.5 VI/WT C210 GN/WT
CLUTCH CONTROL CONTROL MOTOR CRUISE
OUTPUT OUTPUT ENABLE
SEE DASH LIGHTS
GROUND
"N"
OUTPUT
BAND
1.5 GN/WT
1 GN/WT
11
1 GN/WT
.75 GN/WT
.75 GN/WT
1
.75 8U/3R
.75 BU/BR
S234
3
15
1
2
D
6
N
R
P
S
W
0
GN
BU
.5 YL
.5 GN
.5 BU
4
5
SPEEDOMETER
SOLID STATE
2
C8
.5 BU/YL
CRUISE CONTROL
CONTROL UNIT
POWER INPUT
.5 VI/WT
C250
STOP LIGHTS
.5 GN/RD
.5 GN/RD
MANUAL
TRANSMISSION
AUTOMATIC
TRANSMISSION
C208
.5 GN/RD
C208
61-09/5
S224
.5 GN/RD
.5 GN/RD
9
G200
.5 BR
SPEEDOMETER
.5 VI/WT
1.5 VI/WT
S241
FUSE 12
8 AMP
.5 VI/WT
VEHICLE SPEED
INPUT
CRUISE
ENABLE
.75
BU/BR
C8
GROUND
FEEDBACK
REFERENCE
FEEDBACK
INPUT
SOLID STATE
24
26
.5 GY/RD
.5 GN/YL
4
.5 RD
7
.5 YL
.5 BR
3
S233
(-)
12
16
C1
C6
.5 BR
.5 BR
G200
.5 BR
.75 BU/BR
6
7
.75 BU/BR
.5 BU
C209
.5 BU/WT
2
3
G200
13
.5 BK
5
.5 BK
.5 GN
.5 WT
.5 WT
CONTROL
MOTOR
1
