1980 SKODA 120L recommended oil

metre), ond the
relotion of 1
kpm :9.806
Nm is'
opplicoble. When opplied to tightening
torques
of bolts ond nuts, use the relotion
10 Nm :
: 1 kpm.
d) The unit of power (output) tW'
(wott)
reploces the former "h.p."
(horsepower) ond
the relotion
of t h. p.:
735.499 W is opplicoble.
For procticol purposes,
o multiple of kW (kilo-
wott :
1,000 wotts) is used, i. e., t h. p. :
:0.736 kW.
e) The
unit of pressure "Po"
(poscol) or, in
proctice, MPo (megoposcol :
1,000,000 poscols)
or kPo (kiloposcol :
1,000 poscols)
reploces the
former "bor"
ond "kglcmz",
ond the following
relation is opplicoble: 1 MPo: 10 bors :1O.2
kg/cm2 (kp/cm2).
For current meosuring
of tyre
pressure etc., use the relotion: 100 kPo :
1 bor:
:1kglcm2 (kp/cm,) :1
otm.
1.10 GENERAL INSTRUCTIONS
With the exception of o few
speciol pro-
cedures or ossembly techniques
mentioned in
the respective section of
this monuol,
every
removol ond refitting (disossembly
ond re-
ossembly) should be governed
by the following
generol principles:
o) Use suitoble tools ond especiolly tubulor
box sponners which couse the leost domoge
to nuts ond bolt heods.
b) During disossembly note corefully how
the ports
hove been ossembled. This knowledge
is involuoble for correct reossembly.
c) Cleon ports
in trichloroethylene or tech-
nicol petrol.
They do not contoin substonces
(esoeciolly leod) which horm
the skin os motor
petrol does. Current bronds of seoling com-
pounds con be removed with denoturoted
ol-
cohol or scroped off. For o speciol
seoling
compound see the note ot the end of this
chopter.
Avoid contominotion of self-lubricoting
metol
beorings with ony degreosing
ogent os this
would unfovourobly offect their self-lubricoting
properties.
Cleon ports
of the broke ond clutch hydroulic
system with olcohor.
d) Lubricote
oll ports
moving on or in
eoch
other before their ossembly. Operoting lubri-
conts do not spreod eosily on dry surfoces,
the
ports ore not properly
lubricoted, ond friction
oreos ore opt to get
domoged. Coot the os-
sembled ports with the lubricont which is used
to lubricote them in operotion. When lubricoted
with oil, dip
the ports
in motor oil, the f luidity of which mokes
it
especiolly suitoble for
this
purpose. Use greoses
ond hydroulic f luid bronds
specified in the Toble
of Recommended Lubri-
conts.
e) Use new cotter pins
ond metol lock
woshers if you
ore not convinced of the perfect
condition of the old ones which could breok
ond leove the joints
unsecured. Moreover, there
is o risk
of the broken ports
domoging other
functionol ports.
f) Cleon new ontifriction beorings (boll,
rol-
ler, ond topered roller beorings) of preserving
greose using kerosene.
Preserving greose is not
suitoble for lubricotion ond it mixes bodly with
I ubriconts.
g) Some of the joints
hove to be tightened
with o moximum occurocy to the specified
tor-
ques listed in the previous
chopter.
h ) 'Ihe
permissible rototion unbolonce is spe-
cified for some of
the rototing ports,
usuolly in
gcm (gromcentimetres). A well boloqced port
con be stopped in
ony position
if it is
instolled
so thot no rototion resistonce
octs on it. With
the exception of dynomic boloncing, the ports
ore usuolly tested on on ouxiliory shoft ploced
on the
edges. The
unbolonced port
moves from
the deflected position
with its heoviest (i.
e.
unbolonced) port
downword. The
volue of un-
bolonce con be determined
when fostening
o weight corresponding to the permissible
un-
bolonce to the opposite side
of the unbolonced
port. lf the port
does not move when deflected
or if it moves with this weight downword; the
unbolonce is within the recommended limits.
The weight of the testing weight sholl be
de-
termined by dividing the volue of the permis-
sible unbolonce by the distonce of the weight
from the rototion
centre of the port.
i) Even slightly domoged seols ond pockings
must be reploced with new ones
Note: In the foctory,
the speciol seoling
compound
of the "Velvonton
C" brond is used for seoling
the engine reor
cover on the cylinder block, the
moting surfoces of the georbox housing holves,
ond the guide
of the clutch releose beoring.
This seoling compound is mode
on the bose
of o polyurethone
plostic ond it
corresponds to
"Hykemor", "Reineplost", "Curil
K" ond similor
compounds. lt con be removed from the ports
by scroping ond woshing with ocetone, butyl-
ocetone or chlorinoted solvents, for exomple
chloroform (trichloromethone)
ond corbon tetro-
ch loride.
24

2.2-2.3
threods. Fill the etrgine with oil ond the cooling
systenr with on ontifreeze, ond
bleed them.
2.3 REASSEMBLING THE ENGINE
The reossembly procedure depends
on the
extent to which the engine hos been
dis-
rnontled. For better understonditrg, o
reossembly
of o conrpletely disnrontled
engine is described
in the following
porogrophs.
lnspection of
Cylinder Block
1. Clomp the thoroughly cleoned
cylinder
block into the MP 9-101 stond with the engine
corrier type MP 1-101 ond check it for complete-
ness -
see Chopter 2.6. Fit the
block with its
lugs on the engine corrier pins
ond use the side
bolt for ltolding it down.
DK 1188
Fig.2311- Cylinder Block Fostened on the
Assenrbly Stond by lVleons of the MP 1-10-l
Corrier
2. Rernove the pressure
relief volve, moke
sure thot the boll contoct {oces ore cleon,
ond
refit the cleoned volve. Forr
f itting o new volve
see Chopter 2.6.
3. Remove the cronkshoft beoring
covers ond
tlre i;ylinder block reor cover.
To Refit the Cronkshoft
4. Force the beoring shell lrolves with the
fingers into the cronkshoft beoring bores so thot
the shell lip snops home into the slot (cut-out)
in the block ond so thot the shells do not pro'
trude over the beoring surfoces for the beoring
covers, ond lubricote them with engine oil. Be
r;ure to fit shells motching the cronkshoft
i":urnols -
see Chopter 2.7.
5. Slip the oiled guide
ring on the cronkshcft
"vith oil grooves
pointing
toword the cronkshoft
'.veb ond {it the cronkshoft with the pressed-on
boll beoring (see
Chopter 2.7)
into the shell. 6.
Inscrt the
beoring shell
holf ir-rto
the cover
of the beoring No.-l
os described in
porogroph
4,
ond fit the cover with the
recess for the guide
ring turned outword. Proceeding from
the front
of lhe block, slip
on the next guide ring with
the oil grooves pointing
owoy from the block so
thot itJ
lip engoges ogoin into
the slot in the
cover. Coot the ring
with oil ond slip on the
thrust ring. Fit the MP -1'112
thrust collor on the
cronkshofi ond
tighten the
beoring slightly
using the belt
PrrlleY bolt.
7. Instoll the next
two beorirrg covers
corl'l'
plete with beoring shells
ond lightly
tighten l.he
cover nuts.
Press the cork
seol
into the
reo'r
cover moking
sure thot it
f its the groove
snugly
ond slightly bverlops the lower
seoting surfoce'
Before titting the cork seols,
compress them
for
o while in o vice to distort them. Insert the
distorted seols in the grooves
or gops between
the cover qnd
the cylinder block
where they
will expond onci provide
for perfect seoling.
lnsert tob woshers under
the nuts of the
beoring covers
ond while tightening the rruts
check their correct position so os
to enoble
o subsequent correct locking
of the nuts.
Fig.2.312 -
Meosuring Cronkshoft Ploy
1 -
Thrust collor, type
MP 1 112
2 -
Diol indicotor in o
speciolly mode yoke
8. Rotote the cronkshoft severol times ond
using o mollet top the covers ond both shoft
ends to ensure o correct bedding
of the covers
ond cronkshoft guide rings.
9. Tighten the belt pulley nut
to clomp the
thrust ring, ond
rotote ond force
off
the cronk-
shoft to
check its ploy. The
cronkshoft must
be
free to rotote but
without ony
noticeoble ploy.
lf there is o noticeoble ploy, recheck
its volue
ond odiust it by replocing the guide ring with
o new one. The
moximum ploy
should not ex-
ceed 0.10 mm, the recommended minimum ploy
being 0.04 mm. 10.
F
speciol
end onr Drive
suchr o
be turnr
cover. I
ever, tf
the cyl
speciol note in
11. Ti
the tigh
in the
covers. hoving
does no
must ro
Then lo,
woshers
ond nut
To Refil
12. R
greose i
it with i
o flywhr
engine,
with rec
under tt
Chopter
bending
shoft og
powl ins
For flyw
Fig.2.3l3
Using thr
Screw
holes, for
con be ur
further o1
the hondr
30

2.6-2.7
seot in the cylinder block using o copper or
oluminium rod.
Reconditioning Recesses for
Cylinder Liner
Flonges
Before ossembling o used
cylinder block,
inspect ond cleorr thoroughly the moting
sur-
foces of the recesses for
cylinder liner f
longes.
lf chemicol ogents (petrol,
etc.) foil
to hove
the required
effect, or if the surfoces hove
been domoged
mechonicolly, use the MP 1-106
dresser, or the MP 1-157
iig with
universol guicc
rings.
Reconditioning of Comshqft Beorings
lf on oversize
comshoft is to be f itted (ex-
cessive beoring cleoronces in on otherwise
sound block), drive out the plug
on the reor
side of the cvlinder block ond reom
the beor-
ings to dimensions specif ied in the following
Toble:
-0.025To
Grind
For grir
shoft by t
between 1
'Ihe
reor
ond there
for detoils
beoring.
For grir
prepored
clomped t,
pins must
Externol Col
Nomir iourn
Stondord
1st regrin
2nd regrin
3rd regrin
Stondond comshoft
Diometer of beoring in cylinder block
mm
+0.02s
38.5
+0.021
Oversize comshoft lsg
l-
38s-
l-;- -0.041
-0.020
The numerical symbols of the beorings (
l-lll)
indicote the respective
front, centre, ond reor
beari ngs.
Close the newly
mochined bore with o new
plug ond seol
it with o dob of point.
A poor
seoling would result in oil leoking
from the
engine into the clutch.
When reboring the bore for
the comshoft,
observe the centre distonces of the cronkshoft
ond comshoft. Otherwise the timing choin will
be either too slock or too tout. For the correct
distonces see
Fio. 2.6/3. Reconditioning
of Volve Toppet Guides
lf there is on excessive cleoronce in the
guides (beorings) of the volve toppets,
it is
possible to recondition the guides
ond to re-
ploce stondord toppets by toppets
of o lorger
diometer. The centre line of the beorings
is per-
pendiculor (normol) to the seoting foce
of the
cylinder block. The relotive dimensions
of the
beoning ond toppet ore
specified in
the Toble
below: o
L_r
_-L1il I toi .ll
-t
QZt0.l -T-
zi
A'ry
@)
2.7 CRANKSHAFT
AND ITS ACCESSORIES
The cronkshoft hos three rnoin beorings ond
four cronkpin beorings. lt is o forging with sof t,
not hordened iournols. When
worn, it
must be
reground to dimensions os per
Toble for fitting
oversize big-end ond moin beoring shells
os
well os cn oversize guide
ring. Cronkshoft Beoring
(for
clutch shoft)
It will be driven or pressed
into the shoft
lubricoted with the recommended greose
with
its cover turned outword.
After its pressing-in,
odd odditionol greose
by forcing it into the
shoft bore behind the beoring.
Use the extroctor MP 1-109 for
the removol
of the
beoring. Diometer of comshoft
iournols
mm
_ =l__i tl
Volve Toppet Diometer
of Beoring
in Cylinder Block, mmToppet
Diometer
mm
Stondord
on;rsizt- 21
+0.021 21
-0.020
21.2 21.2-0.007
42 4th

6.
Complete the pump
ossembly by fitting
the
Stouffer lubricotor filled with
the recommended
greose.
2.15 ROCKER SHAFT AND ROCKERS
Assembly (on
Skodo 105 engine)
1. Instoll the lock ring, ploin
wosher, ond
spring wosher on the ro6ker shoft
with both
ends plugged.
Smeor the shoft with oil, fit the
rocker (with
its orm with the thrust foce de-
flected toword the next ossembled ports),
the
shim, the rocker support, ond the other
orm
def lected toword the support, i. e. the complete
rocker unit of cylinder
No. 1.
2. Then slip the spring,
the rocker, the sup-
port, the shim,
ond the next rocker, i.e.
the
complete rocker unit of cylinder
No.2, on the
shoft.
3. Threod on the spring ond, using the mirror
orrongement of the ossembled
rocker units,
instoll the rocker
units of the remoining
two
cylinders. Use o lock ring supplemented
with
o ploin
ond o spring wosher
to lock the os-
sembled ports
in position.
The rocker support of the cylinder No.4 must
be provided
with on oil hole
to provide
for the
supply of oil to the rocker shoft.
4. Compress
the springs
by holding down the
rocker orms ond lubricote
oll loterol contoct
surfoces with oil.
Assembly (on Skodo 120 L
ond 120 LS engines)
The rocker shoft is provided
with two od-
ditionol rocker supports fitted from
the outside
of the rocker units (the
shoft is longer), re-
plocing woshers obutting
on the lock rings.
For
the rest, the ossembly is identiccl
with the pro-
cedure described in porogrophs
1 to 4 obove.
NJote: Rocker orms
on the Skodo 120 LS en-
gine ore shorter (18.5
mm) thon those on the
Skodo -120
L ond Skodo 105 engines,
in order
to obtoin o higher rotio.
Disossembly
Remove the lock ring from the shoft
end ond
strike off the
entire volve nocker geor
from
the
shoft.
2.16 CYLINDER HEAD, VALVES
AND
SPRINGS
The cylinder heod is o costing of speciol grey
cost iron. The volve seots ond guides
ore cost
ond mochined directlv in tlre heod. The volves ore of different
diometers, the intoke volves
being lorger. Outer (exhoust)
ports
ore single,
oll remoinlng ore doubled, i.e. bifurcoted
ond
bronching to two volves in odioining
cylinders.
The centre exhoust port
bronches to the cyl.
inders No.2 ond 3, the neighbouring
intoke port
to the cylinders No. 1 ond 2, ond No. 3 ond 4.
The cylinder heod con be hondled
in the cor os
o unit. Of the individuol
iobs, only
the reploce-
ment of volve springs,
cotters, ond cylinder
heod bolts con be corried out with the engine
in. position in the cor. For oll the remoining
iobs, the
cylinder heod hos to be removed
from
the cor.
To remove
the volve springs,
screw out
the
sporking plugs ond, using o tommy
bor with
o curved end (steel
bor of obout 5 mm dio-
meter), broce
the volve to prevent
it from
sliding down into the combustion
chomber.
To Remove
Cylinder Heod from Engine
1. Let
the engine cool down before removing
the cylinder heod to preclude
worping of its
beoring surfoce.
2. Droin
the coolont into o cleon vessel (see
Chopter 15.13), detoch oll ports
connecting the
cylinder heod to the vehicle,
ond remove
oll
ports which ore likely
to obstruct the removol.
3. Remove the oir cleoner,
lift owoy
the
cylinder heod cover, ond remove
the nuts ond
bolts holding down
the cylinder heod (on
en-
gines of Skodo 120 L
ond 120 LS cors, two
bolts olso hold down
the end rocker
shoft sup-
ports) reversing the order of the numbers
in-
dicoted in Fig. 2.1611.
By pulling
the exhoust
monifold, disengoge the
cylinder heod ond lift
it owoy.
To Refit Cylinder
Heod on Engine
. 1.
Locote the cylinder heod gosket
on o per-
fectly cleon surfoce of the cylinder
block (cleon
Fi1.2.1611- Tightening Diogrom of Cylinder
Heod Bolts ond Nuts
For tightening torques see Chopter
1.8 the
cylinc
the oilwo,
structed c
Releose
once odjur
heod. lf nr
the rocker
2. Swin<
down the
porogroph
opply the
liminory o
the sequ€
(Fig. 2.16/
shoft suppr
3. Adjus
ter 2.13,
re
cleoner, rer
tighten oll
Cylinder Hr
Disossem
heod on o r
o support i
it does
not
o iob from
t
An exomple
1. Remove
the cosing
control, end
geor ofter
supports.
Fig.2Je
For holding
c
bolt M 8 scrt
rocker-shoft st
1 -
MP 1-113
v,
2 -
MP 1-114
v
Itl
I
I
/\.
-
( 3 r--{ 4)
\-/
\II
l
/
,/
t___v'
?,3
"'@-:lO
54

Turn
the flonge
on the centering
orbor so thot
the longer, cylindricol port
foces the clutch,
push it ogoinst the friction plote
hub, ond olign
the ends of the levers to touch the flonge.
A deviotion from the ploneness
of 0.1 mm
is
permissible. Use feeler gouges for checking
this deviotion.
lf it is not possible
to odiust the out-trovel of
the clutch releose levers to o volue given
by the
length of the flonge cylindricol port
due to
excessive weor
of the friction plote, odiust to
the next higher volue.
Clinch nuts on the
odiusting nuts bocked off up to the end of the
threod ore o worning of o weor limit which pre-
cludes ony further odiustment
of the clutch.
4. After hoving reossembled
the engine with
o new or odiusted clutch,
check ond, if necess-
ory, odiust the cleoronce between the releose
levers ond the throw-out beoring -
see Chop-
ter 15.4.
3.3 CLUTCH DISMANTLING
Owing to its simplicity,
it is not necessory
to
describe in detoil the dismontling
of the clutch,
but some speciol feotures
deserve ottention.
1. lf the friction plote
ond clutch cover ore
intended to be re-used, mork their relotive
positions using centre punch
morks to preserve
the originol bolonce of the ossembly.
2. To dismontle
the clutch, it is
necessory to
compress the clutch cover to relieve the stress
of the releose lever bolts. For this purpose
use
the MP 2-101
ossembly plote
shown in Fig.3.4/1.
After screwing off the releose lever nuts ond
compressing the clutch cover,
the clutch is
reody for dismontling.
3.4 CLUTCH REASSEMBLY
1. Locote
the clutch pressure
plote
on the
MP 2-101
ossembly plote
ond fit springs
on the
cylindricol bosses. Before fitting
the springs, it
is odvisoble to check them for
complionce with
the volues specified
in the following Toble.
Toble of Clutch Springs
Lood
Length of spring in mm
lin -rrr"ltp1
Mounted length
31.55'10+36
(s2t3.6)
Length of compressed spring 29.5
I 580 (59) 2.
Instoll retoining plotes
on the clutch
springs ond fit the clutch cover with releose
lever springs in position.
Assemble the clutch
cover with the pressure plote,
observing the
morks indicoting their relotive positions.
When
ossembling new pot'ts,
their positions
ore of no
consequence.
3. Slip o 4.5 mm high pod
over the ossembly
plote bolts (the
plote
con be used
for Skodo
1000 MB ond Skodo 100 cors os well,
ond by
using pods
of different heights, the plote
con be
odopted for different
types of clutches), fit the
yoke of the
iig on
the plote
bolt ond compress
it by screwing down the nut till the bottom port
rests on the pod.
When compressing the clutch
cover toke core thot the projections
of the
pressure plote
ore correctly centered in
the
cover slots to prevent
o distortion of the clutch
cover.
4. Slip the bottom ends of the releose levers
under the springs instolled in the cover ond fit
them with their longitudinol
slots on the sup-
ports. Slip odiusting woshers on the bolts of the
pressure plote ond screw down the nuts with
their cylindricol port
focing the woshers. Then
odjust the height of the releose levers with
these nuts so thot their ends touch the shoulder
of the yoke
bottom port.
The difference of the
lever height should not exceed 0.'l mm. This
odiustment olso sets the recommended
distonce
of the levers from the pressure
plote
beoring
surfoce.
Use clinch nuts for locking the odiusting nuts
in position,
put
supporting clips under the re-
leose f ever ends os shown in Fig.3.111 ond3.212,
ond slocken the nuts of the ossembly plote.
The
clips ore useful when fitting the clutch to the
f lywheel since it is not necessory to overcome
the tension of the clutch springs.
To Check Adiustment ond Bolance
The described od justment
of the releose levers
in the
iig is
the most occurote, the ossembly Fig.3
Dim
plote be
simulotin
For on<
porogropl
The cl
with the
friction ;
ports of '
clutch on
To bol
centering
pressure
the chips
lf thesr
boloncing ing holes
in o circk
4mmofr
between
fostening
3.5 FR|C
lf the f
it is odvi
8.5 mm th
When r
the frictio
ond only r
complicot
After hr
the plote
if necessc
recheckinl
quired.
70 Fig.3.4l1
-
IAP 2lol
Assembly Plote with Clutch

The
clutch moster
cylinder is port
of the
ossembly of the broke moster cylinder ond
pedols. For the odiustment of the pedol
free
trovel, etc. see Chopter 12.1.
Pipeline ond Hoses
The rigid port
of the pipeline
comprises
speciol steel pipes,
the some os those of the
broke system. However, they hove o diometer
of 6 mm os compored with the 5
mm diometer
pipes of the broke system. For
their servicing,
repoirs, ond replocement see Chopter 9.7.
The flexlble port
of the clutch hydroulic
line comprises o high-pressure broke hose.
No
speciol position
or fostening ore recommended.
I N
Il'
I
til
lt
h .t*
: i'*
;::
..:tn
., i oilfl
Fig.3.612
-
Clutch Moster Cylinder
1 Sectionol
View
72

r
t
i
5. Prc
scri bed
rods onc
4th spee
fork rod,
irr the b
6. lnsl
guide bu
cover inr heods. S
tob wos
edges of
F it thr
stri ki ng
weoker s
ing forks 7. Tigl
the forks fork rod
the strik
function
Reverse-:
Fig
-1 - Rever
2-1st-o
3-3rd- o
4 -
Rever
8. Inst
press-f ittr
verse-spe
inside th
through t
Turn tl'
end foces
lock it in
hole. Tigl
Pinion Ar
9. Instc
ing ond,
r
_-_-- -
. i\:r,,,
\. 43
Fig. A.1l'l -
Power Pock
1 -
engine with mounting, 2 -
georbox/f inol
drive with
mounting, 3 -
reor oxle (holf-oxles),
4 -
rodius orms
retighten it using the recommended torque
(Chopter 1.8) ond screw down the clinch nut.
lf necessory, top up engine oil, f ill the cooling
system witlr on qntifreeze,
bleed the broke sys-
tem, ond
odiust the hond broke.
For the fosten-
ing of broke hoses (routing)
see Chopter 9.7.
4.2 ASSEMBLING
GEARBOX
Generolly, the reossembly
p'rocedure
depends
on the extent, to wlrich the unit hos been token
oport. For betterunderstonding,
we sholl des-
cribe the procedure
ond peculieorities
of reos-
sembly of o completely
disossembled unit.
Gear Chonge Mechonism
. 1.
Clomp the right-hond holf of the housing
(when viewed from the flonge securing
it to
the engine) in the MP 9-101 stond
com-
plemented with the MP 3-101 georbox
rock, ond
check the housing for completeness.
2. Instoll
circlips on the striking fork rods
of
the reverse
ond 1st ond 2nd speed. The ring
with the lower
nose is to be fitted
on the 1st--
ond 2nd-speed rods.
3. lnsert the reverse speed
striking fork rod
into the housing
so thot the inserted
end pro-
trudes slightly from its guide,
slip on it the
striking fork with the longer
side of its heod
first,- ond push
the striking fork rod through
the fork
ond the end of the guide
os for os=it
will go. 4. Fit tlre
MP 3-109 jig
into the free holes for
striking fork rods (both pins
of the
iig), ond
proceeding through the hole in its side ond
using o stick or o length of wire, push
the lock
pin into the housing
os for os it will go.
Proceed
in the some monner for
inserting the next pin
(use one pirr
of the
iig). Shift
it
iust so thot
the centre lrole remoins free for inserting
the
striking rod.
Puslr the lock pin
into the end
guide of the strikirrg
fork rods olso os for os it
will go. The
iig is not required
for
the instol-
lqtion of this pin.
Fig.4.2l1- Clomping Georbox Housing in Stond
Using MP 3-101 Rock
Fig.4.212 -
Locking Striking Fork Rods in
Position bv Meons of Lock
Pins ond Bolls
78 Fig.4.2l3
-
Instolling Lock Pins Using
MP 3-109 Jig

5.
rl in
t-o o
el
st
th
w
ce
re
q
tr
t
Fig.
5.1i3 -
Forcing Slroft out of Beoring Using
MP 5-113 Jigs ond Jirrs os per
Fig. 5."1/1
The oxle shoft moy Inove out of the holf-oxle
only to such on extent thot the reor edge of the
beoring thrust ring is flush
with the holf-oxle
socket. Otherrwise it is opt to
foll out of the
epicyclic geor
ond its refitting would require
the removol
of the holf-oxle from
the georbox
housing. 4. To fit o new boll beoring proceed
occording
to Chopte'r 5.2.
Pull out ogoin
the shoft slightly
until the thrust ring con be seen, fit the beoring
I I
I of the
broke mechonism
odhering to the in-
structions of the obove-mentioned chopter,
lo'
cote the beoring
shim 0.3 mm thick, ond com'
plete the ossembly.
Note: The 3 mm shim should
be used only
when replocing the wheel hub or when elimirr-
oting on oscertoined shoft ploy,
thot is
to soy
if the shoft moves oxiolly ond
knocks. However,
it is recommended never
to use more shims
thon three.
5. A domoged seoling
ring con be removed
with o hook or o needle, ond o new one driven
or pressed-on.
The lotter olternotive should be
preferred with regord to the visuol checking of
the pressing-on operotion. The
tightening fin
ond spring of the pocking
hove to be
tunned in-
side the holf-oxle.
When driving home the seol
ring, slip the
MP 5-114 pilot toper (see
Fig.5.213) on the
shoft,
smeor it with oil, ond move the seoling
ring
olong it to drive it finolly into the holf-oxle
using tlre MP 5-116 drift os shown in Fig-
5-212.
For pressing-on
the seoling ring, use the MP
5-112 iig (see
Fig. 5.214)
ond the, sleeve
with
toper os per
Fig.5.-1l4. Pull the shoft
slightly out
of'the holf-oxle, slip
on it the oiled toper os
shown in the illustrotion, then the
seoling ring
ond finolly the sleeve. Fosten the MP 5-112
iig
screwing its heod on
the holf-oxle threod, slip-
the seoling ring on
the thrust ring
by meons of
the sleeve, ond turn the wrench to
press
the
seoling ring into the holf-oxle.
Now the beoring con
be pressed ott.
l^5
oi ro --
€D
.90 DK 827
4 '%
I i5
t"'
I
-l
b
F)
g
d
e \
r
e
.l I
€['----
Fig. 5.1i4 -
Sleeve ond Toper for Pressing'on
Holft-Axle Seoling Ring (toper
surfoce
smoothed out during monufocture)
12
90
6"44 t;)
20 96