1980 SKODA 120L oil type

Worrring
lights:
5 -
left-hond direction indicotors, green
6 -
oil pressure,
red
7 -
right-hond direction indicotors, green
8 -
broke system, red
9 -
chorging, red
10 -
fuel reserve, omber
11 -
high beom, blue
The thermometer indicotes the temperoture
of the coolont with the ignition switched on.
The optimum operoting temperoture ronge is
from 75 to 105oC. In
SfOon 105 S, this
ronge
is identified by
the green
zone of the scole.
The fuel gouge
indicotes the level
of the fuel
with the ignition switched on. The scole is
provided with divisions 0 -
r/2
-
1, i. e., empty,
holf full,
ond full
tonk.
The driver is worned by the red worning light
when thene ore less thon 5litres of fuel in the
fuel tonk.
The tochometer indicotes the speed (revol-
utions) of the engine. The
speed should
never
rise to the red zone. When chonging the geors,
on increose of speed within the ronge
of the
yellow zone is permissible.
The porking
lights come on when the switch
is thrown to the first
right-hond position.
The
Fig. 1.3/6 Switches -
port I
1 -
Porking light switch ond feeder of heodlomp
dipswitch
2 -
Horn switch, direction indicotor switch,
ond dipswitch
3 -
Switch of ouxiliory (extro)
heodlomps
4 -
Door switch 12
-
unoccupied, green -
fog lomp worning light
included in speciol
extros
13 -
unoccupied, green -
low-beom worning light
included in speciol
extros
14 -
unoccupied, red
switch switches on the heodlomps, toil lights,
ond the licence plote
light.
The heodlights, i. e. driving (high
beom) ond
dipped (low
beom), ore switched on by throw-
ing the switch to the second
right-hond pos-
ition. The switch switches on oll porking
lights
ond the heodlights
in occordonce with the pos-
ition of the switch stem-type lever: centre
position -
dipped lights,
towords the instrument
ponel -
driving lights. When the
driving lights
ore on, the blue worning light glows.
The ouxiliory heodlomps
come on ofter pull.
ing the switch knob, but only while moin
heod-
lomps ore on.
heodlomp flasher storts floshing
when
the switch lever
toword the steering
ring.
horn is sounded by depressing
the lever
the steering wheel shoft.
Fig.1.317 Switches -
port ll ond oshtroy
1 -
Switchbox ond steering lock
2 -
Switch of windscreen wipers ond
wosher
3 -
Heoter switch
4 -
Switch for on odditionol device -
not
stondord fitted
5 -
Disobility worrning light
switch -
not on
SKoDA 105 s
6 -
Heoter control
7 -
Ashtroy
The
pulling
wheel
The
toword
i
I
L 12

Broke
fluid:
- clossificotion
- brond filled-in in the foctrY -
FUEL TANK
Locotion Fuel cleoning (filtrotion)
CHASSIS LUBRICATION
TyPe
ELECTRICAL EQUIPMENT
Eorthing
Roted voltoge
Service voltoge
lgnition
Storoge botterY .
Alternator PAL Magneteton
Voltoge regulotor
Distributor
lgnition coil
Storter motor
Sporking plugs -
see ChoPter 137
BODYWORK
Type Seoting copocity
Luggoge comportments, coPocitY
H e oter
FILLING CAPACITIES
Engine -
Skodo 105 S, 105 L
ond 120 L
Skodo 120 LS
Georbox ond
finol drive cose
Steering box
Broke system
ond clutch
Cooling system
Fuel tonk SAE J
1703C
SYNTOL HD
190
suspended under
floor boord of cor reor holf
stroiner in fuel tonk,
fuel filter, ond stroiner
in corburettor
self-lubricoting beori
ngs,
by greose nipples;
wheel
greose
negctive pole
12 volts
14 volts repocking
with greose
beorings pocked
with
bottery (coil)
type
type AKUMA 6N 37 -
12 volts, 37 ompere-hours
14V 35 amps 1976-79
1O5/12O
L
14V 42 amps 1979 on
1O5/12O
L
14V 42 amps 1976-79
120 LS
14V 55 amps 1979 on
120
LS
type PAL Mogneton, 14 volts
type PAL Mogneton
with centrifugol timing
device ond vocuum unit
type PAL Mogneton, 12
volts
type PAL Mogneton, 12
volts
0.66 kilowotts (0.9
h. p.)
oll-metol, closed, four'door,
chossisless body
5 occuponts
0.40 mi (0.28
rn: moin luggoge comPortment for
q lood of obout
0 kg, 0.12 mr interior luggoge
comportment for
o lood of obout 10 kg)
hot-woter heoter
with fon, fed with woter
from
the engine cooling sYstem
4 litres moximum -
2.5 litres minimum
of engine oil
4.6 litres moximum -
3 litres minimum
of engine oil
2.5 lities of geor
oil (2 litres when
chonging oil)
0.16 litres of gecrr oil (obout
0.25 litres when
topping up)
O.4A titres of broke f
luid (f
illing for tropicol
regions, etc. see ChoPter 16.2)
12.5 litres of
ontif'reeze
38 litres 1.8 Tt(
BC
1. Ap
von ized
out o sL
2.tti
Threo
ENGINE
Connecti
Nut of c
Nut of c
Nut of vr
Nut of fr
Nut of c
Nut of si Nut of c'
Cylinder Bolt of c
Flywheel
Bolt of cr
Oil sump
Oil sump
Droin plu
Bolt of ft
Bolt of oi
Socket ol
Oil pressr
Sporking
CLUTCH Connectir Generol
20 Bolt
foste

2.2-2.3
threods. Fill the etrgine with oil ond the cooling
systenr with on ontifreeze, ond
bleed them.
2.3 REASSEMBLING THE ENGINE
The reossembly procedure depends
on the
extent to which the engine hos been
dis-
rnontled. For better understonditrg, o
reossembly
of o conrpletely disnrontled
engine is described
in the following
porogrophs.
lnspection of
Cylinder Block
1. Clomp the thoroughly cleoned
cylinder
block into the MP 9-101 stond with the engine
corrier type MP 1-101 ond check it for complete-
ness -
see Chopter 2.6. Fit the
block with its
lugs on the engine corrier pins
ond use the side
bolt for ltolding it down.
DK 1188
Fig.2311- Cylinder Block Fostened on the
Assenrbly Stond by lVleons of the MP 1-10-l
Corrier
2. Rernove the pressure
relief volve, moke
sure thot the boll contoct {oces ore cleon,
ond
refit the cleoned volve. Forr
f itting o new volve
see Chopter 2.6.
3. Remove the cronkshoft beoring
covers ond
tlre i;ylinder block reor cover.
To Refit the Cronkshoft
4. Force the beoring shell lrolves with the
fingers into the cronkshoft beoring bores so thot
the shell lip snops home into the slot (cut-out)
in the block ond so thot the shells do not pro'
trude over the beoring surfoces for the beoring
covers, ond lubricote them with engine oil. Be
r;ure to fit shells motching the cronkshoft
i":urnols -
see Chopter 2.7.
5. Slip the oiled guide
ring on the cronkshcft
"vith oil grooves
pointing
toword the cronkshoft
'.veb ond {it the cronkshoft with the pressed-on
boll beoring (see
Chopter 2.7)
into the shell. 6.
Inscrt the
beoring shell
holf ir-rto
the cover
of the beoring No.-l
os described in
porogroph
4,
ond fit the cover with the
recess for the guide
ring turned outword. Proceeding from
the front
of lhe block, slip
on the next guide ring with
the oil grooves pointing
owoy from the block so
thot itJ
lip engoges ogoin into
the slot in the
cover. Coot the ring
with oil ond slip on the
thrust ring. Fit the MP -1'112
thrust collor on the
cronkshofi ond
tighten the
beoring slightly
using the belt
PrrlleY bolt.
7. Instoll the next
two beorirrg covers
corl'l'
plete with beoring shells
ond lightly
tighten l.he
cover nuts.
Press the cork
seol
into the
reo'r
cover moking
sure thot it
f its the groove
snugly
ond slightly bverlops the lower
seoting surfoce'
Before titting the cork seols,
compress them
for
o while in o vice to distort them. Insert the
distorted seols in the grooves
or gops between
the cover qnd
the cylinder block
where they
will expond onci provide
for perfect seoling.
lnsert tob woshers under
the nuts of the
beoring covers
ond while tightening the rruts
check their correct position so os
to enoble
o subsequent correct locking
of the nuts.
Fig.2.312 -
Meosuring Cronkshoft Ploy
1 -
Thrust collor, type
MP 1 112
2 -
Diol indicotor in o
speciolly mode yoke
8. Rotote the cronkshoft severol times ond
using o mollet top the covers ond both shoft
ends to ensure o correct bedding
of the covers
ond cronkshoft guide rings.
9. Tighten the belt pulley nut
to clomp the
thrust ring, ond
rotote ond force
off
the cronk-
shoft to
check its ploy. The
cronkshoft must
be
free to rotote but
without ony
noticeoble ploy.
lf there is o noticeoble ploy, recheck
its volue
ond odiust it by replocing the guide ring with
o new one. The
moximum ploy
should not ex-
ceed 0.10 mm, the recommended minimum ploy
being 0.04 mm. 10.
F
speciol
end onr Drive
suchr o
be turnr
cover. I
ever, tf
the cyl
speciol note in
11. Ti
the tigh
in the
covers. hoving
does no
must ro
Then lo,
woshers
ond nut
To Refil
12. R
greose i
it with i
o flywhr
engine,
with rec
under tt
Chopter
bending
shoft og
powl ins
For flyw
Fig.2.3l3
Using thr
Screw
holes, for
con be ur
further o1
the hondr
30

primory
feed to the distributor coincides with
the connecting line of the
distributor centre
line ond the first cylinder
heod
bolt os
per
Fig.2.3l10. Secure the distributor in this pos-
ition by lightly tightenning the tie-bolt ond
remove the timing geor
cover from the cylinder
block. The used type of distributor is described
in Chopter 13.5.
Fig.2.3l10 -
Position of Distributor on Engine
-l - screw of primory power
feed
2 -
cylinder heod bolt
3 -
index line rnorking the position
of the
distributor ornr when cvlinder No. 1 f ires
24. Coot with oil the moting
surfoces of the
timing geor cover ond the cylinder
block, locote
the cover gosket
on the block,
oil the timing
choin ond the comshott worm geor.
Remove the
f lywheel powl
ond rotote the
cronkshoft through
360o so
os to bring tlre pistons
of the cylinders
No. 1 ond 4 to their TDC position
ogoin. This
position corresponds opproximotely
to the volve
geor position
when the cylinder No. 1 f ires (the
tips of the coms of
cylinder No. 1 ore turned
downword, owoy from
the engine). Lock the
cronkshoft in position by refitting ond tight-
ening the flywheel powl.
25. Turn
the distributor orm in the direction
of the
screw (1) in occordonce with Fig. 2.3110,
hold it down with the
finger in this position,
ond ref it the timing geor
cover on the cylinder
block. By sliding the worm geor
of the distribu-
tor drive into the comshoft worm geor,
the orm
is turned to coincide with the timing
mork for
cylinder No. 1
on the distributor housing. lf
there is no coincidence of the orm ond timing
mork, od just
the position
of the orm by
slightly
rototing the distributor.
lf the
misolignment of the distributor
ornr
ond the timinq
mork of the
cvlinder
No'1 is so greot
thot it connot be corrected
by rototing
the distributor, remove
the timing geor
cover,
rotote the distributor slightly ond repeot
the
entire procedure
of refitting the timing geor
cover. 26. Smeor the protruding
end of the cronk-
shoft ond the outer shoft end (stem)
of the
belt
pulley with oil, f
it the belt pulley,
the nespective
wosher, ond tighten the bolt. Bolt the
PumP
suction stroiner tothe cronkshoft centre beoring
ond use o spring
wosher under the bolt heod.
27. Bolt down the timing geor
cover using
spring woshers ond
cheese-heod bolts
(exclus-
ively) cnd f inolly fosten the timing geor
cover
in such o position
thot the contoct breoker
points open before the crronkshoft with
the con-
necting rod ond piston
hos ottoined the top
deod centre (TDC)
position (see
the lgnition
Timing Toble in Chopter 15.3).
For checking the ignition odvonce, on electric
power supply is required with o bulb connected
in o circuit with the distributor. this
circuit
being interrupted by the oction of the contoct
breoker. An odopted conventionol torch with o
metol
iocket con be
used with odvontoge for this
purpose. Remove the flywheel powl ond
set the re-
quired ignition odvonce by turning the cronk-
shoft with o screw'driver inserted into
the geor
ring ond propped ogoinst the cylinder block
f longe. Rotote the shof t onticlockwise o bit
more thon necessory ond
bock it off so os to
odiust the bocklosh of the timing geors
ond the
distributor drive geors.
oK 6ls
Fi9.2.3111- Lomp for Checking the Opening
of Contoct Breoker Points
-1 - torch complete with dry cell ond bulb
2 -
leod with olligotor clomp
3 -
botterv cell
4 -
torch coo
5 -
contoct spring
6 -
insuloting plote
7 -
electricol-contoct connection of the leod
with the
drv cell Con
using
torch.
the br
slowly
indico
A corr
is not
timing 28.L
beorin
Then f
while
oil sun
the thr
the tyl
see Cl.
shri n ks
of the
woter
move i
ively.
To Fit
Toppetr
25. r
remove
positior
sure thr
cylinder
cylinder nuts. F<
first bo
woteir p
oir clec
finol ti1
2.16.
Ploin
heod bo
which t
woshers
no wosl
heod bo
cy I i nder
the outs
hove to
of the rc
Tighte
broce or,
30. Sc
thermom
into the
cosing o
ofter ho
Use spri
thermost
cooted g
with the
with the
The th
should br
34

ilil
ll
I
Z,l
spring woshers under the pump
fostening nuts.
36. lnstoll the oil filter -
see Oil Filter in
Chopter 15.3.
37. Bolt the brocket ond the reloy lever
of the
occelerotor linkoge to the intoke monifold, Use
spring woshers to lock the bolts in position.
38. Locote the corburettor gosket, sheet
guord, onother gosket,
the insuloting wosher,
ond o third gosket (oltogether
three goskets
of
the some type) on the intoke monifold inlet
socket, instoll the corburettor,
ond tighten
it
down with nuts.
On 105 ond 120 l- engines, the sheet guord
must be fitted to the intoke monifold inlet
socket with o throttling spider, while 120 LS
engines must hove the possoge
unobstructed.
39. Smeor the boll pins
of the linkoge
ond
corburettor lever with greose
contoining molyb-
denum disulphide
ond mount on them the oc-
celerotor link (tie-rod).
Hold the link in pliers
ond slip securing clips over the heods.
Hook o spring on the shonk of the reloy
link-
oge boll pin
ond on the rib of the forehousing
on the corburettor.
40. Screw down the vocuum
control pipe
on
the corburettor (using
double-sided seoling
rings) ond slip on the rubber
hose connecting
the pipe
with the distributor vocuum control
unit. Secure the pipe
by bending the clip under
the nut of the intoke ond exhoust monifold.
To Refit Alternotor
41. Attoch the olternotor
brocket to the side
of the cylinder block while putting
ploin
woshers under
the nuts. Mount the olternotor
holder together with the engine mounting lug
on the bolt of the timing geor
cover ond the
front lug of the cylinder block.
Use self-locking
nuts for the bolts f ostening the olternotor
holder. Lock
the lower bolt of the lug by meons
of o spring wosher
ond nut. Using onother bolt,
bolt together the lug ond the brocket. lnsert
the tie-bolt from
the side
of the lug, slip on
o ploin
wosher ond tighten the nut. Fit the
short-circuit strip on the bolt ond lock it in
o position
porollel
with the olternotor brocket
by screwing
down the respective nut with
o ploin
wosher.
42. Put the olternotor into the holder,
ttrreod
in the bolt, ond screw down the nut with o ploin
wosher without tightening. Without tightening
the self-locking
nut, bolt the strut into the
brocket on the cylinder heod. Swing the olter-
notor toword the engine, fit
the V-belt ond,
while tensioning it, connect the olternotor with
the strut using o bolt, spring wosher ond nut.
At the some time, tighten the nut of the bolt
holding down the olternotor
in the
holder ond
the nut of the bolt connecting the strut with
the holder. For the belt slock odiustment see
Chopter 15.3. 43.
Fosten the second
engine mounting lug
using nuts with spring woshers.
To Fit Cylinder Heod, Air
Cleoner,
ond Sporking Plugs
44. Fit the cylinder heod
with cemented.on
gosket on the cylinder block ofter hoving slip-
ped o seoling ring ond o wosher on eoch bolt,
the some os in the cose of the push-rod
cover.
In oddition, fit the fuel pipe
holder on the reor
bolt ond hold it down by slightly tightening the
nut.
45. Fit the oir cleoner in position
ond fosten
it to the corburettor with o bolt using o seoling
ring ond wosher. Put o spring wosher
under the
nut on the brocket
ond screw down the nut on
the bolt of the cover without ony wosher.
46. Threod the fuel hose through its holder
on the cylinder heod ond use clips to fosten it
to the corburettor ond pump.
Adiust the most
suitoble position of the hose by rototing
the
holder ond then tighten the nut.
47. Attoch hoses connecting the oir cleoner
with the corburettor ond the oil filler neck.
When preporing
the cc for driving in winter,
instoll the winter
oir-intoke tube (hose) -
for
detoiled instructions see Chopter 15.3 "Air
Cleoner -
Winter Operotion".
48. Screw in the sporking plugs
with seoling
iings ond fit the ignition cobles. For the re-
commended types of sporking plugs
see Chopter
13.7.
The outlet on the distributor cop morked with
o notch is intended for
the coble
to cylinder
No. 1. The
remoining outlets ore.to be counted
clockwise ond in direct
order from 1
to 4 ond
the cobles will be connected to sporking plugs
in the order of numbers cost on the cylinder
heod beside the recesses for sporking plugs.
Plug Screws ond Lubricotion
System
Accessories
49. Plug the oil sump with the conicol screw
plug with its
seoling ring. In the cose of on
engine without the oil cooler, plug
the oilwoy
on the timing geor
cover with o screw plug
with o seoling
ring, ond the oilwoy ot the reor
end of the cylinder block with o pressure
switch. lf the socket for screwing down the
pressure switch is missing, instoll o new socket
together with its respective seoling ring.
lf on oil cooler is provided,
hoses ond o press-
ure switch should be
connected to the oilwoys
occording to Chopter 11.9.
Put the oil dipstick
with the f itted rubber ring
in its ploce.
For the type of the dipstick see
Chopter 2.17.
50. Using spring
woshers with the bolts,
screw down the flywheel
guorcl
ofter removing
36

d)
e) f) choke
plunger
sticking in its
bottom
position storting worm engine
too high fuel level in floot chomber
incorrectly odiusted
idle run unstick
the plunger
or reploce it with
o new one
odjust the
floot
odiust idle
run correctlY
2.2O FUEL PUMP
Technicol DescriPtion
The model JIKOV MF 3407 fuel pump
is of
the diophrogm ond
lever type, controlled by the
round disc of the comshoft. The suction
motion
of the diophrogm is octuoted by the
lever, the
dischorge motion by the spring of
the dio-
phrogm. Fuel flows through o stroiner, o mud
trop, ond the suction volve to the delivery
volve. A priming lever is provided
for hond
priming of the fuel. The moving mechonism
is
lubricoted with oil
sploshed from the cylinder
block. Stroke of the driving disk 4
mm
Suction heod 1.5
mm
Deliveryheod. 2mm
Pump dischorge ot 2,000 strokes
per minute ond free outflowwithout
counter-pressure 30
ltrs/hr.
Mointenonce, Repoirs, Disossembly
ond Reossembly
For routine
mointenonce (cleoning
of the
mud-trop screen) see Chopter 15.3. After hoving
operoted the hond-priming lever lift it
till it
engoges sofely in its locked position.
ln the cose of o defect, inspect the diophrogm
ond check the volves for leokoge. After hoving
removed the pump
from the engine, remove the
mud trop, seporote the upper port
from the
lower port,
ond remove two screws, holding
down the thrust plote,
to lift owoy the volves.
Swill oll ports
in petrol
ond blow off with com'
pressed oir. Reploce domoged ports
with new
ones. lf necessory, remove the diophrogm from the
octuoting lever in
the lower port
of the fuel
pump (its
monufocturer recommends the dio-
phrogm to be reploced ofter obout 50,000 kilo-
rnetres with o new
one). Do not stretch the
spring of the diophrogm ond do not olter its
compression force chorocteristic in ony woy.
Do not forget to put
fibre pocking rings
underthe
volves
when reossembling the
fuel
PumP.
Put o spocer ring under the suction volve (close
to the mud trop). Fig.2.2Ol1 shows
the pos-
itions of volves ond the holding-down thrust
plote. Put the spring
of the diophrogm into
the
lower port
oi the pump
ond engoge the pin
ot
the diophrogm with the octuoting lever. Oper-
ote the hond lever
to compress the dioPhrogm
oncl hold it in position by inserting o
rod of 4.5
to 5 mm diorneter (for
exomple the
shonk of
o drill, etc.) between the octuoting lever
ond
the woll of the pump
lower
Port.
Now bolt both pump
ports
together so thot
the mud trop is on the
right-hond side when
viewing the pump from obove
ond the fostening
flonge from the front. Use spring
woshers
under the clomping bolts.
Fig.2.2011 -
Section Through
Fuel Pump
lf it is necessory to verify
the dischorge of
the pump
by o test, note the following require'
mentswhich the pump
must meet otl80strokes
per minute:
o) 15 ltrs/hr. ot f ree outf low without
fuel
counterpressure
b) minimum pressure
of 0.018 MPo (1.8
m of
woter column) ot
o zero off'toke of fuel
c) o dry pump
must drow fuel from o
depth of
1.5 m in 16 seconds.
Fuel Pump Defects ond Their Removol
1. Foulty fuel
supply
o) clogged mud trop
b) domoged diophrogm
2. Fuel pump
does not hold fuel
o) dirty or defective volves cleon it
reploce it
with o new one
wosh them in petrol,
reploce defective
volves with new ones
66

Turn
the flonge
on the centering
orbor so thot
the longer, cylindricol port
foces the clutch,
push it ogoinst the friction plote
hub, ond olign
the ends of the levers to touch the flonge.
A deviotion from the ploneness
of 0.1 mm
is
permissible. Use feeler gouges for checking
this deviotion.
lf it is not possible
to odiust the out-trovel of
the clutch releose levers to o volue given
by the
length of the flonge cylindricol port
due to
excessive weor
of the friction plote, odiust to
the next higher volue.
Clinch nuts on the
odiusting nuts bocked off up to the end of the
threod ore o worning of o weor limit which pre-
cludes ony further odiustment
of the clutch.
4. After hoving reossembled
the engine with
o new or odiusted clutch,
check ond, if necess-
ory, odiust the cleoronce between the releose
levers ond the throw-out beoring -
see Chop-
ter 15.4.
3.3 CLUTCH DISMANTLING
Owing to its simplicity,
it is not necessory
to
describe in detoil the dismontling
of the clutch,
but some speciol feotures
deserve ottention.
1. lf the friction plote
ond clutch cover ore
intended to be re-used, mork their relotive
positions using centre punch
morks to preserve
the originol bolonce of the ossembly.
2. To dismontle
the clutch, it is
necessory to
compress the clutch cover to relieve the stress
of the releose lever bolts. For this purpose
use
the MP 2-101
ossembly plote
shown in Fig.3.4/1.
After screwing off the releose lever nuts ond
compressing the clutch cover,
the clutch is
reody for dismontling.
3.4 CLUTCH REASSEMBLY
1. Locote
the clutch pressure
plote
on the
MP 2-101
ossembly plote
ond fit springs
on the
cylindricol bosses. Before fitting
the springs, it
is odvisoble to check them for
complionce with
the volues specified
in the following Toble.
Toble of Clutch Springs
Lood
Length of spring in mm
lin -rrr"ltp1
Mounted length
31.55'10+36
(s2t3.6)
Length of compressed spring 29.5
I 580 (59) 2.
Instoll retoining plotes
on the clutch
springs ond fit the clutch cover with releose
lever springs in position.
Assemble the clutch
cover with the pressure plote,
observing the
morks indicoting their relotive positions.
When
ossembling new pot'ts,
their positions
ore of no
consequence.
3. Slip o 4.5 mm high pod
over the ossembly
plote bolts (the
plote
con be used
for Skodo
1000 MB ond Skodo 100 cors os well,
ond by
using pods
of different heights, the plote
con be
odopted for different
types of clutches), fit the
yoke of the
iig on
the plote
bolt ond compress
it by screwing down the nut till the bottom port
rests on the pod.
When compressing the clutch
cover toke core thot the projections
of the
pressure plote
ore correctly centered in
the
cover slots to prevent
o distortion of the clutch
cover.
4. Slip the bottom ends of the releose levers
under the springs instolled in the cover ond fit
them with their longitudinol
slots on the sup-
ports. Slip odiusting woshers on the bolts of the
pressure plote ond screw down the nuts with
their cylindricol port
focing the woshers. Then
odjust the height of the releose levers with
these nuts so thot their ends touch the shoulder
of the yoke
bottom port.
The difference of the
lever height should not exceed 0.'l mm. This
odiustment olso sets the recommended
distonce
of the levers from the pressure
plote
beoring
surfoce.
Use clinch nuts for locking the odiusting nuts
in position,
put
supporting clips under the re-
leose f ever ends os shown in Fig.3.111 ond3.212,
ond slocken the nuts of the ossembly plote.
The
clips ore useful when fitting the clutch to the
f lywheel since it is not necessory to overcome
the tension of the clutch springs.
To Check Adiustment ond Bolance
The described od justment
of the releose levers
in the
iig is
the most occurote, the ossembly Fig.3
Dim
plote be
simulotin
For on<
porogropl
The cl
with the
friction ;
ports of '
clutch on
To bol
centering
pressure
the chips
lf thesr
boloncing ing holes
in o circk
4mmofr
between
fostening
3.5 FR|C
lf the f
it is odvi
8.5 mm th
When r
the frictio
ond only r
complicot
After hr
the plote
if necessc
recheckinl
quired.
70 Fig.3.4l1
-
IAP 2lol
Assembly Plote with Clutch

Remove the clip of
the
clutch throwout beor-
ing guide,
insert the MP 3-102
iig into
the guide,
open its iows, ond withdrow the
guide.
After
hcving renewed the seol ring, drive home the
guide using the MP 3-103 drift. The droin hole
in the guide
must foce
downword.
The lotest desing of the extrocting
iig hos
the type dcsiqnotion MP 3-112. Screw the
iig
bolt into
the
iig nut
inserted into the mech-
onism through the hole cleored by the removol
of the clutch releose cylinder. Jerk the
iig to
drive the guide
out of the housing.
Dismontling the Power Pock
For complete dismontling of the power pock,
remove it from the cor -
see Chopter 4.-1,
"Rernovol of Power Pock from the Cor". Then
proceed os follows:
1. Remove the front cover ond the cover of
the pinion boll beoring, the clutch releose
mechonism, ond the clip of the guide
of the
clutch throwout sleeve, i. e., oll component
ports ottoched
to both holves of the housing.
2. Remove the connecting bolts of the flon-
ges. Force oport the f longes using o screwdriverr
inserted into the chombers of the flonge feet
(lugs). Lifting owoy oll component ports
one
by one is the usuol procedure
of dismontling.
Toking oport of lorger units (pinion,
etc.) is
described individuolly
in the following
chopters.
3. Press out the beoring cups which hove
remoined in the housing ofter its holves hove
been seporoted.
Use the MP 5-107
iig supported
by the MP 5-108
iig.
Fig.4.al2 -
Pressing Out the Cup of the Topered
Roller Beoring
Using MP 5-107 ond MP 5-108
Jigs
4.5 FRONT COVER
The front cover ossembly forms
o self-con-
toined unit fitted to the georbox.
For both the
reossembly ond dismontling ploce
it on o work
bench. Assembling
Front Cover
1. Slip the rubber seol ring on the speedo-
meter beoring ossembly (beoring
with geors)
ond push
corefully the beoring, preferobly
by
o steody rotory motion, into the cover
iust for
enough to be oble to instoll the key
without
domoging the seol ring by the shorp edge of
the keywoy. For the some reoson, chomfer the edge of the
beoring bore before
instolling the beoring in
o new cover.
2. Lock the beoring in the oxiol direction by
instolling the key
ond spring woshers, ond by
screwing down the nut.
Slip the clip on
the
protruding pcrt of the beoring ond lock it olso
in the oxiol direction with o bolt, spring
wosher,
ond nut. Do not
tighten the nuts fully.
3. Instoll the oiled geor
chonge lever in the
cover while pushing
it only os for os the groove
for the seol
ring.With the lever in this position,
insent the seol ring
in its groove
ond push
forther the lever through the ring. Slip the
dust
boot on the lever ond ottoch it to the cover
with o length
of locking wire.
4. Attoch the fostening (mounting)
lugs using
copscrews ond spring woshers. There
is o right-
-hond ond o left-hond lug, ond their slots must
be turned owov from the cover.
FK 1t't4
Fig.4.5l1- Front
Cove'r Assembly
Dismontling Front Cover
Lift owoy the speedometer
beoring ofter
hoving removed the sleeve
clomping bolt ond
the key (held
down by the nut). Then
withdrow
the geor
chonge lever by simply pulling
it out.
4.6 PINION WITH GEARS The pinion
with geors
forms o self-contoined
unit to be instolled in the georbox.
Use o work
bench ond o press
fon both its ossembly onddismor
wheel sure t
Only c
wheel
m itted
drive.
4.8.
Whe
olso tl
o new
one is
Assem 1.P
the pi
the or" thrust
toworc
3-104 p
ground
the be, must t
meosul
2.S
collor I
ring ir
the grr
The rir
3.5 to I
th ickes
ond pu
speed
3.H
it the '
selecte
toword
dismor (by tol
itinp
free to
Clon
MP 3.1
Note
inner b
toining
either r
-speed
ports.
4. Tr
groovir
pinion.
friction
groover
groove!
5. On
ond fit
the nex sizes 3
84