1980 SKODA 120 LS tow

Worrring
lights:
5 -
left-hond direction indicotors, green
6 -
oil pressure,
red
7 -
right-hond direction indicotors, green
8 -
broke system, red
9 -
chorging, red
10 -
fuel reserve, omber
11 -
high beom, blue
The thermometer indicotes the temperoture
of the coolont with the ignition switched on.
The optimum operoting temperoture ronge is
from 75 to 105oC. In
SfOon 105 S, this
ronge
is identified by
the green
zone of the scole.
The fuel gouge
indicotes the level
of the fuel
with the ignition switched on. The scole is
provided with divisions 0 -
r/2
-
1, i. e., empty,
holf full,
ond full
tonk.
The driver is worned by the red worning light
when thene ore less thon 5litres of fuel in the
fuel tonk.
The tochometer indicotes the speed (revol-
utions) of the engine. The
speed should
never
rise to the red zone. When chonging the geors,
on increose of speed within the ronge
of the
yellow zone is permissible.
The porking
lights come on when the switch
is thrown to the first
right-hond position.
The
Fig. 1.3/6 Switches -
port I
1 -
Porking light switch ond feeder of heodlomp
dipswitch
2 -
Horn switch, direction indicotor switch,
ond dipswitch
3 -
Switch of ouxiliory (extro)
heodlomps
4 -
Door switch 12
-
unoccupied, green -
fog lomp worning light
included in speciol
extros
13 -
unoccupied, green -
low-beom worning light
included in speciol
extros
14 -
unoccupied, red
switch switches on the heodlomps, toil lights,
ond the licence plote
light.
The heodlights, i. e. driving (high
beom) ond
dipped (low
beom), ore switched on by throw-
ing the switch to the second
right-hond pos-
ition. The switch switches on oll porking
lights
ond the heodlights
in occordonce with the pos-
ition of the switch stem-type lever: centre
position -
dipped lights,
towords the instrument
ponel -
driving lights. When the
driving lights
ore on, the blue worning light glows.
The ouxiliory heodlomps
come on ofter pull.
ing the switch knob, but only while moin
heod-
lomps ore on.
heodlomp flasher storts floshing
when
the switch lever
toword the steering
ring.
horn is sounded by depressing
the lever
the steering wheel shoft.
Fig.1.317 Switches -
port ll ond oshtroy
1 -
Switchbox ond steering lock
2 -
Switch of windscreen wipers ond
wosher
3 -
Heoter switch
4 -
Switch for on odditionol device -
not
stondord fitted
5 -
Disobility worrning light
switch -
not on
SKoDA 105 s
6 -
Heoter control
7 -
Ashtroy
The
pulling
wheel
The
toword
i
I
L 12

Lifting
the cor with o
Power iock -
When
r-rsing o service
Power iock, let the
cor rest on
the points
shown in Fi1.1.412.
To tow the cor, hook the towing rope on
to
the brocket under
the cor nose. Threod the pin
through the loop of the rope
ond the brocket
lugs ond secure the pin
with o cotter pin (both
thL pin
ond the cotter pin
ore included in the
cor occessories).
1.5 SPARE WHEEL
AND FUEL TANK
Spore wheel -
After having opened the
lug-
goge boot lid, pull the hondle of the spore
wheel corrier releose
rod.
The corrier is
re-
leosed ond swings
down (speciol equipment of
the cor includes
o sofety lotch behind the
bumper which hos to be pushecl
oside to
releose the corrier
) . After
hoving closed the corrier (by
lifting it),
push the releose lever under
the bumper to the
right os for os it will go.
Fuel tonk -
The filler neck with cop is in the
reor on the right-hond
side of the cor- lt con
be locked ond unlocked by meons of
the re'
spective key.
1.6 STARTING THE
ENGINE AND CHECKING
ITS CORRECT RUNNING
1. Moke sure thot the geor
lever is in its
neutrol position,
switch on the ignition (pos-
ition I on the switch box) ond wotch the
coming on of the oil pressure ond chorging
worning lights, i.
e. check the function of the
olternotor -
see the informotion in porogroph
4.
Prepore the engine
to its temperoture:
- Storting from cold in
the occelerotor pedol
- Storting from cold in
the occelerotor pedol
choke for
storting occording
winter -
do not touch
ond use the full choke
summer -
do not touch
ond use only holf of the
Fig. 1.5/1 Hondle ot
Rod (f ronr obove )Spcre
Wheel Lock
crnrl Safety Lotch -
Storting o wormed-up engine -
depress the
occelerotor pedol
slowly to tlre
toe-boord, do
not touch the choke
2. Depress the clutch pedol
(odvisoble
in
summer, necessory in
winter) ond stort
the
engine by turning the ignition key to position
ll.
Let go
of the key os soon os the engine fires
ond releose the occelerotor pedol
{if it hos
been
clepressed).
It the engine ,refuses
to fire, return the key
to the position "0"
ond rePeot the
storting
Pro-
cedure. lf the engine is wormed up, depress the
occelerotor pedol
to obout one third of its totol
trovel. lf the cold engine stolls even
ofter the
second ond third storting ottemPt, enrich the
storting mixture by quickly
depressing the
oc-
celerotor pedol
once or twice to holf of its
trovel during the next storting ottemPt.
Never let tlre storter motor run for more
thon
obout 5 seconds. Woit
some 5 seconds before
repeoting the storting.
Fuel is injected
by every quick
depression of
the occelerotor pedol
ond enriches the mixture
so thot it is difficult to ignite. lf the engine
is flooded, stort
it
with o fully depressed oc-
celerotor pedol.
3. Increose the engine speed corefully while
releosing the clutch pedol. lf the
engine shows
signs of stolling, depress
ogoin the clutch
pedol.
Relecse
L.ever
Fi.1.5t2 Fuel Tcrtrk Filler
Neck
16

2.2-2.3
threods. Fill the etrgine with oil ond the cooling
systenr with on ontifreeze, ond
bleed them.
2.3 REASSEMBLING THE ENGINE
The reossembly procedure depends
on the
extent to which the engine hos been
dis-
rnontled. For better understonditrg, o
reossembly
of o conrpletely disnrontled
engine is described
in the following
porogrophs.
lnspection of
Cylinder Block
1. Clomp the thoroughly cleoned
cylinder
block into the MP 9-101 stond with the engine
corrier type MP 1-101 ond check it for complete-
ness -
see Chopter 2.6. Fit the
block with its
lugs on the engine corrier pins
ond use the side
bolt for ltolding it down.
DK 1188
Fig.2311- Cylinder Block Fostened on the
Assenrbly Stond by lVleons of the MP 1-10-l
Corrier
2. Rernove the pressure
relief volve, moke
sure thot the boll contoct {oces ore cleon,
ond
refit the cleoned volve. Forr
f itting o new volve
see Chopter 2.6.
3. Remove the cronkshoft beoring
covers ond
tlre i;ylinder block reor cover.
To Refit the Cronkshoft
4. Force the beoring shell lrolves with the
fingers into the cronkshoft beoring bores so thot
the shell lip snops home into the slot (cut-out)
in the block ond so thot the shells do not pro'
trude over the beoring surfoces for the beoring
covers, ond lubricote them with engine oil. Be
r;ure to fit shells motching the cronkshoft
i":urnols -
see Chopter 2.7.
5. Slip the oiled guide
ring on the cronkshcft
"vith oil grooves
pointing
toword the cronkshoft
'.veb ond {it the cronkshoft with the pressed-on
boll beoring (see
Chopter 2.7)
into the shell. 6.
Inscrt the
beoring shell
holf ir-rto
the cover
of the beoring No.-l
os described in
porogroph
4,
ond fit the cover with the
recess for the guide
ring turned outword. Proceeding from
the front
of lhe block, slip
on the next guide ring with
the oil grooves pointing
owoy from the block so
thot itJ
lip engoges ogoin into
the slot in the
cover. Coot the ring
with oil ond slip on the
thrust ring. Fit the MP -1'112
thrust collor on the
cronkshofi ond
tighten the
beoring slightly
using the belt
PrrlleY bolt.
7. Instoll the next
two beorirrg covers
corl'l'
plete with beoring shells
ond lightly
tighten l.he
cover nuts.
Press the cork
seol
into the
reo'r
cover moking
sure thot it
f its the groove
snugly
ond slightly bverlops the lower
seoting surfoce'
Before titting the cork seols,
compress them
for
o while in o vice to distort them. Insert the
distorted seols in the grooves
or gops between
the cover qnd
the cylinder block
where they
will expond onci provide
for perfect seoling.
lnsert tob woshers under
the nuts of the
beoring covers
ond while tightening the rruts
check their correct position so os
to enoble
o subsequent correct locking
of the nuts.
Fig.2.312 -
Meosuring Cronkshoft Ploy
1 -
Thrust collor, type
MP 1 112
2 -
Diol indicotor in o
speciolly mode yoke
8. Rotote the cronkshoft severol times ond
using o mollet top the covers ond both shoft
ends to ensure o correct bedding
of the covers
ond cronkshoft guide rings.
9. Tighten the belt pulley nut
to clomp the
thrust ring, ond
rotote ond force
off
the cronk-
shoft to
check its ploy. The
cronkshoft must
be
free to rotote but
without ony
noticeoble ploy.
lf there is o noticeoble ploy, recheck
its volue
ond odiust it by replocing the guide ring with
o new one. The
moximum ploy
should not ex-
ceed 0.10 mm, the recommended minimum ploy
being 0.04 mm. 10.
F
speciol
end onr Drive
suchr o
be turnr
cover. I
ever, tf
the cyl
speciol note in
11. Ti
the tigh
in the
covers. hoving
does no
must ro
Then lo,
woshers
ond nut
To Refil
12. R
greose i
it with i
o flywhr
engine,
with rec
under tt
Chopter
bending
shoft og
powl ins
For flyw
Fig.2.3l3
Using thr
Screw
holes, for
con be ur
further o1
the hondr
30

Fig.2.3/6
-
Position of Cylinder Liners,
Pistons
ond Connecting Rods in Engine
1 -
Proiectlon of cylinder liners
obove the top
foce of the cylinder block (0.125 -
0.155 mm)
2 -
Connecting rod splosh hole
'3
- Arrow on the piston
heod pointlng
toword
the comshoft
4 -
Comshoft
Fig.2.317 -
Pilot Ring
for Piston Rings
Dimensions of pilot
ring to motch cylinder
liner diometer:
dio. 68 D:68 H 7
dio. 68.25 D :68.25
H 7
dio. 68.50 D :68.50
H 7
dia. 72 D:72 H7 14.
Hoving fitted the piston
rings ond con-
nectlng rods on the pistons,
turn the piston
ring
gops so thot they ore stoggered
through 120o.
Coot the entire surfoce of the piston
with the
fitted rings with oll ond insert the pistons
ossembled with the connecting rods into the
liners in the sequence of the corresponding
numbers of cylinders ond connecting rods. Moke
sure thot the
orrow in the piston
heod points
toword the morking
of the cylinder liners, l.e.
toward the comshoft, ofter the ossembly with
the cylinder block. This
is importont in thot it
does owoy with odditionol turning of the pis-
tons in the liner ond o posslble
displocement
of the piston
ring gops.
Smeor the top surfoce of the cylinder block
with point
or o seoling
compound before
instol-
ling the liners with the pistons
ond connectlng
rods into the cylinders in the order of their
numbering. It is odvisoble to prepore
o sheet sleeve or
o pilot
ring occording to Fig. 2.317
to com-
press the piston
rings when fitting
the piston
Into the cylinder liners. Force the piston
into
the sleeve or pilot
ring so
thot the piston
heod
is flush with its edge or protrudes
sllghtly
over it, locote the piston
on the liner, ond then
force down the piston
through the sleeve or
pilot ring into the liner.
15. Ploce suitoble ouxiliory devices over two
holes for
cylinder heod bolts, for exomple
lorge-diometer woshers, ond screw them down
Fig. 2.3/8 -
Fitting Piston into
Cylinder Liner
Using the Pilot Rlng
1 -
pilot ring
2 -
cylinder liner
32

ilil
ll
I
Z,l
spring woshers under the pump
fostening nuts.
36. lnstoll the oil filter -
see Oil Filter in
Chopter 15.3.
37. Bolt the brocket ond the reloy lever
of the
occelerotor linkoge to the intoke monifold, Use
spring woshers to lock the bolts in position.
38. Locote the corburettor gosket, sheet
guord, onother gosket,
the insuloting wosher,
ond o third gosket (oltogether
three goskets
of
the some type) on the intoke monifold inlet
socket, instoll the corburettor,
ond tighten
it
down with nuts.
On 105 ond 120 l- engines, the sheet guord
must be fitted to the intoke monifold inlet
socket with o throttling spider, while 120 LS
engines must hove the possoge
unobstructed.
39. Smeor the boll pins
of the linkoge
ond
corburettor lever with greose
contoining molyb-
denum disulphide
ond mount on them the oc-
celerotor link (tie-rod).
Hold the link in pliers
ond slip securing clips over the heods.
Hook o spring on the shonk of the reloy
link-
oge boll pin
ond on the rib of the forehousing
on the corburettor.
40. Screw down the vocuum
control pipe
on
the corburettor (using
double-sided seoling
rings) ond slip on the rubber
hose connecting
the pipe
with the distributor vocuum control
unit. Secure the pipe
by bending the clip under
the nut of the intoke ond exhoust monifold.
To Refit Alternotor
41. Attoch the olternotor
brocket to the side
of the cylinder block while putting
ploin
woshers under
the nuts. Mount the olternotor
holder together with the engine mounting lug
on the bolt of the timing geor
cover ond the
front lug of the cylinder block.
Use self-locking
nuts for the bolts f ostening the olternotor
holder. Lock
the lower bolt of the lug by meons
of o spring wosher
ond nut. Using onother bolt,
bolt together the lug ond the brocket. lnsert
the tie-bolt from
the side
of the lug, slip on
o ploin
wosher ond tighten the nut. Fit the
short-circuit strip on the bolt ond lock it in
o position
porollel
with the olternotor brocket
by screwing
down the respective nut with
o ploin
wosher.
42. Put the olternotor into the holder,
ttrreod
in the bolt, ond screw down the nut with o ploin
wosher without tightening. Without tightening
the self-locking
nut, bolt the strut into the
brocket on the cylinder heod. Swing the olter-
notor toword the engine, fit
the V-belt ond,
while tensioning it, connect the olternotor with
the strut using o bolt, spring wosher ond nut.
At the some time, tighten the nut of the bolt
holding down the olternotor
in the
holder ond
the nut of the bolt connecting the strut with
the holder. For the belt slock odiustment see
Chopter 15.3. 43.
Fosten the second
engine mounting lug
using nuts with spring woshers.
To Fit Cylinder Heod, Air
Cleoner,
ond Sporking Plugs
44. Fit the cylinder heod
with cemented.on
gosket on the cylinder block ofter hoving slip-
ped o seoling ring ond o wosher on eoch bolt,
the some os in the cose of the push-rod
cover.
In oddition, fit the fuel pipe
holder on the reor
bolt ond hold it down by slightly tightening the
nut.
45. Fit the oir cleoner in position
ond fosten
it to the corburettor with o bolt using o seoling
ring ond wosher. Put o spring wosher
under the
nut on the brocket
ond screw down the nut on
the bolt of the cover without ony wosher.
46. Threod the fuel hose through its holder
on the cylinder heod ond use clips to fosten it
to the corburettor ond pump.
Adiust the most
suitoble position of the hose by rototing
the
holder ond then tighten the nut.
47. Attoch hoses connecting the oir cleoner
with the corburettor ond the oil filler neck.
When preporing
the cc for driving in winter,
instoll the winter
oir-intoke tube (hose) -
for
detoiled instructions see Chopter 15.3 "Air
Cleoner -
Winter Operotion".
48. Screw in the sporking plugs
with seoling
iings ond fit the ignition cobles. For the re-
commended types of sporking plugs
see Chopter
13.7.
The outlet on the distributor cop morked with
o notch is intended for
the coble
to cylinder
No. 1. The
remoining outlets ore.to be counted
clockwise ond in direct
order from 1
to 4 ond
the cobles will be connected to sporking plugs
in the order of numbers cost on the cylinder
heod beside the recesses for sporking plugs.
Plug Screws ond Lubricotion
System
Accessories
49. Plug the oil sump with the conicol screw
plug with its
seoling ring. In the cose of on
engine without the oil cooler, plug
the oilwoy
on the timing geor
cover with o screw plug
with o seoling
ring, ond the oilwoy ot the reor
end of the cylinder block with o pressure
switch. lf the socket for screwing down the
pressure switch is missing, instoll o new socket
together with its respective seoling ring.
lf on oil cooler is provided,
hoses ond o press-
ure switch should be
connected to the oilwoys
occording to Chopter 11.9.
Put the oil dipstick
with the f itted rubber ring
in its ploce.
For the type of the dipstick see
Chopter 2.17.
50. Using spring
woshers with the bolts,
screw down the flywheel
guorcl
ofter removing
36

{
Smoll End ond
Big End Alignment
A misolignment of the centre line
of the
smoll-end bush ond big-end beoring
or the bore
for the big-end
beoring shells must never ex-
ceed 0.03
mm per 'lO0
mm of the connecting
rod length. For checking
ond olignment use
the
MP 1-102 or 1-159 f ixture.
Insert the odiusting pin
into the fixture ond
set both its diol indicotors to
zero. Clomp the
connecting rod without shells
into the fixture,
threod the pilot
pin
in it, ond swing
down the
connecting rod. The recdings
of the diol indi-
cotors will
show ony misolignment of the
smoll
ond big end. The moximum misolignment must
not exceed 0.03
mm os olreody mentioned.
Check for misolignment in two plones by tilting
the diol indicotors.
Two pilot
pins ore supplied, one with o
di-
ometer of 20 rnnr. the
other with o diometer of
20.05 mm, to motch the gudgeon
Pins.
To Motch Connecting Rod
with Gudgeon Pin
ond Cronkshoft
With regord to the reciprocoting movement
of the piston,
the gudgeon pin must hove
the
smollest possible
cleoronce in the
connecting
rod small end (ony lorger cleorcnce results
in
pin knocking). Therefore
select from
severol
gudgeon pins
one which will
be o close running
fit in the smoll-end
bush. lf no suclr pin is
ovoiloble, reom
tlre bush but never exceed the
moximum toleronce limits.
An oversize buslr lros to be
reomed to o nom-
inol diometer of 20.05 mm. For
the respective
dimensions refer to
the Toble supplied with
gudgeon pins. The big"end
beorings
i:;hells)
inouta be
selected occording to the nominol
diometer of the cronkpin. The
shells lrove no
diometer ntorking
oncl hove to be identif !ed
by meosuring their woll thickness with o mi'
crometer.
Motching Big-end Beoring
shells
with Cronkpins
MotchingCronkpin o"|,,n"iifl",,l ro,u,on
nominol diometer
1 thick"ness
mm
mm mm
45 (stondord)
44.75 (1st
regrinding)
44.50 (2nd
regrinding)
44.25 (3rd regrinding)
44 {:lttr regrinding) 1.490
1.615
1.740
1.865
1 990 0.007
Numericol lderrtif icotion of
Connecting Rods
For better identificotion, {igures con
be
stomped on the bosses of
the connecting rod
big end ( see Fig 2 11
1) . The f igures corre-spond with
the
number of the respective
gVtin-
derwithwhich theconnecting rod
is ossembled.
When replocing o connecting rod,
provide the
new connecting rod
with its very some identi-
ficction numbel. Stomp
the figures os much
toword the for end of the boss os possible to
ovoid fouling the loterol guide foce.
2.12 CYLINDERS, CONNECTING RODS
AND PISTONS
o) Only o cylinder (liner)
ond piston of
equot
'
diometer ond the some toleronce closs con
be ossembled qs
s unit.
b) Theengine cs qn
ossembly unit con befitted
cnly with cylinder liners ond pistons
of the
some diometer, the pistons being
of the
some weight grnLtp.
The inclividuol cylinder'cnd-piston qssemblies
con be, however, of dif
ferent toleronce
closses. On the othe'r hond, connecting rods
of only the sqme weight group
con be used-
These ore the cc;tditions for
the correct op-
erotion of pistons in the
cylinders ond for the
correct boloncing of the cronk mechonism.
For detoils concerning dimensions (diometers),
toleronce closses (cylinder liners, pistons) ond
weight groups
(connecting rods ond pistons)'
refei to fhe chcpters deoling with
the
individuol
pc|rts"
To Assembie Cylinder Liner
with Piston
qnd Connectirrg Rod
1. Toke cylinder liners ond pistons with
motching dinrensions, i. e.
cylinder liners of the
some boie (they need
not be necessorily of the
scrme toleronce closs), pistons
of the some
cliometer <,nrl tcieronce closs
to motch those of
the cvlinclr:i iitrers
ond of the sonre weight, oncl
connectitrct rorls, of rtne of
tlle twtl weiglrt
cl roLr PS.
lti''
DK 1161 2.
1
OCCorl Selec'
cyl i nd
tolpro
the (
motch Son
pin or
gudge
in wh
suitob
bush.
Mor
respor
with v
meric<
Rod'.
3.L
the gr-
80"c i Sme
home
some
threod
Pin, o
circlip
on thr
pressi I
Fit
hole ir
the orr
4.F
or exp
detoils
the ri
groove
5- Pr
the crc
ond co
2.13 I
In or
ter ist ic
coms o
comsh<
c leoror
the cor
Volve '
with
lntoker
open be
close o
Fi,c 2.1211 -
Press'f ittirrg
of Gudgeon Pin into
Piston Usinq MP 1-i04
Drift
50

Alternoting
cylinder No. 1
cylinder No.3
cylinder No.4
cylinder No. 2 Adjust cleoronce
on
cylinder No.4
cylinder No.2
cylinder No. 1
cylinder No.3
Fi1.2.1312
-
Volve Cleoronce Adjustment link from the choin
front side ond fit the clip
from the reor with its open end pointing in
the
direction opposite to the choin movement.
Before storting work on the volve geor,
re-
move the oil sump (engine
bottom cover to
which the timing geor
cover is bolted, the suc-
tion stroiner being ottoched to the cronkshoft
centre beoring cover) ond lock
the cronkshoft
in position
in the oxiol direction by depressing
the clutch pedol,
if removol of the entire engine
is not intended for onother purpose.
For speciol
points of the removol refer to
Chopter 2.4.
2.14 WATER PUMP
Disossembly 1. Unlock the wosher of the belt pulley
nut,
remove the nut ond pull
off the belt pulley
using
the MP 1-120 puller (o
fixturre for
Skodo MB 1000
cors) or o universol puller,
for the bolts of which
it is necessory to
cut threods M 8 in the belt
pulley holes.
By pulling
off the belt pulley,
occess will be
goined to the nuts fostening the pump
to the
engine. The some procedure
holds good
when
dismontling the pump
ofter it hos been removed
from the engine.
2. Withdrow the keyfrom
the shoft ond, using
the drift MP 1-121, drive
or press
out the shoft.
Then lift owoy the
housing plote
from the
seoting foce of the pump.
3. Remove the circlip locking the outer boll
beoring in position.
Proceeding from the reor
side of the pump
housing, drive out the boll
beorings with their spocer tube, ond remove
the
rubber seoling rring
from the housing.
Reossembly 1. Smeor the rubber seoling ring with greose
ond insert it into the pump
housing.
Use the
MP 1-123 drift to drive home the inner boll
beoring (without
sheet guord) pocked
with
greose. When opplying the drift,
fit its guide
ring into the bore for the
oute,r boll beoring.
2. Fit the gosket
on the pump
seoting foce
ond ploce
the pump plote
with its cemented-on
gosket (focing outwords from the pump)
over it.
Fosten the plote
to the pump provisionolly
with
one bolt to prevent
the gosket
from being dom-
oged during the following ossembly
iobs.
Insert the rubber seol,
wosher, ond conicol
spring into the speciol (bokelite)
seoling ring
of the pocking glond.
Instoll the spring
with
its nose
into the hole in
the bokelite pocking.
Slip the ossembled pocking glond
on the shoft
with the spring toword the shoft geor,
ond drive
the shoft home into the pump
beoring, while
supporting the beoring with the MP 1-123 drift. Fig.2
4. Fit t
shoft ond
stolling th
in positior
it with gre
sheet guor
5. Top
t
lieve the r
@@@@
DK 1240
Fig.2.1313 -
Volve Arrongement in Cylinderr Heod
Block disks -
exhoust volves
White disks -
intoke volves
Timing Choin ond Timing
Geors
Modified chain and gears
fitted since October
1979 recognised by
squared gearteeth
and chain
with split rollers.
The timing choin hos no slock odiuster (ten-
sioner). A slock choin does not substontiolly
offect the volve geor
occurocy but its operotion
is noisy. Therefore
its correct length should
be
ensured either
o) by selecting o suitoble choin from o number
of choins ovoiloble -
try it on the timing
geors, o1r
b) by replocing the stondord comshoft geor
with on oversize geor
(with greoter
toler-
onces). The comshoft geors
ore groded
in
keeping with their progressive
size (tol-
eronces) into closses A, B ond C. With the
exception of
closs A, the closs morking
letters ore stomped next
to the punch
mork.
For trying, the choin con be disconnected
to ovoid removing ond refitting of the timing
geors. To recouple the choin, insert the coupling Fig.2.1t
52

6.
Complete the pump
ossembly by fitting
the
Stouffer lubricotor filled with
the recommended
greose.
2.15 ROCKER SHAFT AND ROCKERS
Assembly (on
Skodo 105 engine)
1. Instoll the lock ring, ploin
wosher, ond
spring wosher on the ro6ker shoft
with both
ends plugged.
Smeor the shoft with oil, fit the
rocker (with
its orm with the thrust foce de-
flected toword the next ossembled ports),
the
shim, the rocker support, ond the other
orm
def lected toword the support, i. e. the complete
rocker unit of cylinder
No. 1.
2. Then slip the spring,
the rocker, the sup-
port, the shim,
ond the next rocker, i.e.
the
complete rocker unit of cylinder
No.2, on the
shoft.
3. Threod on the spring ond, using the mirror
orrongement of the ossembled
rocker units,
instoll the rocker
units of the remoining
two
cylinders. Use o lock ring supplemented
with
o ploin
ond o spring wosher
to lock the os-
sembled ports
in position.
The rocker support of the cylinder No.4 must
be provided
with on oil hole
to provide
for the
supply of oil to the rocker shoft.
4. Compress
the springs
by holding down the
rocker orms ond lubricote
oll loterol contoct
surfoces with oil.
Assembly (on Skodo 120 L
ond 120 LS engines)
The rocker shoft is provided
with two od-
ditionol rocker supports fitted from
the outside
of the rocker units (the
shoft is longer), re-
plocing woshers obutting
on the lock rings.
For
the rest, the ossembly is identiccl
with the pro-
cedure described in porogrophs
1 to 4 obove.
NJote: Rocker orms
on the Skodo 120 LS en-
gine ore shorter (18.5
mm) thon those on the
Skodo -120
L ond Skodo 105 engines,
in order
to obtoin o higher rotio.
Disossembly
Remove the lock ring from the shoft
end ond
strike off the
entire volve nocker geor
from
the
shoft.
2.16 CYLINDER HEAD, VALVES
AND
SPRINGS
The cylinder heod is o costing of speciol grey
cost iron. The volve seots ond guides
ore cost
ond mochined directlv in tlre heod. The volves ore of different
diometers, the intoke volves
being lorger. Outer (exhoust)
ports
ore single,
oll remoinlng ore doubled, i.e. bifurcoted
ond
bronching to two volves in odioining
cylinders.
The centre exhoust port
bronches to the cyl.
inders No.2 ond 3, the neighbouring
intoke port
to the cylinders No. 1 ond 2, ond No. 3 ond 4.
The cylinder heod con be hondled
in the cor os
o unit. Of the individuol
iobs, only
the reploce-
ment of volve springs,
cotters, ond cylinder
heod bolts con be corried out with the engine
in. position in the cor. For oll the remoining
iobs, the
cylinder heod hos to be removed
from
the cor.
To remove
the volve springs,
screw out
the
sporking plugs ond, using o tommy
bor with
o curved end (steel
bor of obout 5 mm dio-
meter), broce
the volve to prevent
it from
sliding down into the combustion
chomber.
To Remove
Cylinder Heod from Engine
1. Let
the engine cool down before removing
the cylinder heod to preclude
worping of its
beoring surfoce.
2. Droin
the coolont into o cleon vessel (see
Chopter 15.13), detoch oll ports
connecting the
cylinder heod to the vehicle,
ond remove
oll
ports which ore likely
to obstruct the removol.
3. Remove the oir cleoner,
lift owoy
the
cylinder heod cover, ond remove
the nuts ond
bolts holding down
the cylinder heod (on
en-
gines of Skodo 120 L
ond 120 LS cors, two
bolts olso hold down
the end rocker
shoft sup-
ports) reversing the order of the numbers
in-
dicoted in Fig. 2.1611.
By pulling
the exhoust
monifold, disengoge the
cylinder heod ond lift
it owoy.
To Refit Cylinder
Heod on Engine
. 1.
Locote the cylinder heod gosket
on o per-
fectly cleon surfoce of the cylinder
block (cleon
Fi1.2.1611- Tightening Diogrom of Cylinder
Heod Bolts ond Nuts
For tightening torques see Chopter
1.8 the
cylinc
the oilwo,
structed c
Releose
once odjur
heod. lf nr
the rocker
2. Swin<
down the
porogroph
opply the
liminory o
the sequ€
(Fig. 2.16/
shoft suppr
3. Adjus
ter 2.13,
re
cleoner, rer
tighten oll
Cylinder Hr
Disossem
heod on o r
o support i
it does
not
o iob from
t
An exomple
1. Remove
the cosing
control, end
geor ofter
supports.
Fig.2Je
For holding
c
bolt M 8 scrt
rocker-shoft st
1 -
MP 1-113
v,
2 -
MP 1-114
v
Itl
I
I
/\.
-
( 3 r--{ 4)
\-/
\II
l
/
,/
t___v'
?,3
"'@-:lO
54