1973 OPEL MANTA gear

REAR AXLE40- 11
Figure
48-3 Removing Axle Bearing Retaining Ring
seat and lateral runout of axle shaft flange near larg
est diameter.
Permissible radial runout is .002”, and permissible
“lateral runout is
.OO4”. An axle shaft which exceeds
these tolerances, or one which has been otherwise
damaged during removal, must be replaced.
2. Using installer ring J-21721-2, press on bearing so
that oil seal groove on bearing faces shaft splines.
3. Using installer ring J-21721-2, press on retainer
ring so that shoulder faces bearing.
Figure 48.4 Measuring for Axle Shaft Bearing Depth4. Check axle shafts end play as follows:
a. Using a depth gauge, measure depth of rear axle
bearing seat in axle housing (backing plate and gas-
kets in place). See Figure
4B-4.b. Measure width of bearing outer race. The differ-
ence between the two measurements indicates the
required thickness of the shims. The maximum per-
missible end play is .002”. If necessary to reduce end
play, add
,004” shims behind bearing as necessary. A
slight crush fit (up to ,006”) is desirable.
5. Coat rear axle shaft splines with hypoid gear lubri-
cant prior to installation.
6. Insert axle shaft into housing; using a mallet, drive
axle shaft completely into housing.
7. Install lock washers and nuts. Torque to 20
Ib.ft.8. Install brake drum and wheel assembly.
9. Remove supports and lower rear of car to floor.
DISASSEMBLY AND ASSEMBLY OF THE
DIFFERENTIALRemoval and installation of parts for service de-
scribed in the following sub-paragraph can be per-
formed with the rear axle assembly in the car. The
car must be raised and adequately supported to per-
mit access to the parts to be serviced.
Removal and Disassembly of Differential Case1. With car suitably supported at rear jack bracket
on each side, remove differential cover bolts and let
lubricant drain into suitable container.
2. Disconnect left end of track rod and wire to left
shock absorber.
3. Remove both rear wheels and brake drums.
4. Working through access holes in axle shaft flange,
remove four nuts and washers that retain the axle
shaft dust shield and brake backing plate to the axle
housing.
5. Unscrew rear axle shaft retaining plate.
6. Install axle shaft puller J-8805 coupled with slide
hammer J-2619 on axle shaft flange to remove rear
axle. In removing axle shaft, care should be exercised
to avoid damage to the oil seal. See Figure
4B-5.7. Remove differential cover and discard gasket.
8. Check and record ring gear backlash.

4S- 121973 OPEL SERVICE MANUAL
12. Insert adapter J-2241-1 1 in differential case bear-
ing hub and remove side bearings using puller J-22588 with adapter leg J-22939. See Figure
4B-6.13. Remove the differential case to ring gear bolts
and tap ring gear off case using a soft faced hammer.
14. Remove the differential pinion shaft retaining pin
using a
l/8” pin punch. See Figure 4B-7. Remove
pinion shaft, pinion gears, differential side gears and
thrust washers.
Figure 46.5 Removing Axle Shaft18
9. Mark differential side bearing caps and carrier
with a prick punch, so the caps can be reinstalled in
their original positions.
10. Remove differential side bearing cap bolts and
caps.11. Using two wooden hammer handles, pry differen-
tial case assembly from carrier. Do not drop or inter-
change differential side bearing outer races.
SIDE BEARING
PVLLER J-2258846.6
/NFigure
48-S Removing Differentiel Side BesrlngaPINION
SHAFTPINION
kSHAFT
LOCK PIN487
Figure 48-7 Removing Pinion Shaft Lock Pin
Removal and Disassembly of Drive Pinion
1. Remove torque tube assembly.
J-22932
SPLINE HOLDER4&8
Figure
48-E Removing Pinion Preload Nut

J-781 B INSTALLERiUNDERLINED
4B16Figure 46-16
- Pinion Gear Reference Number
NOTE: The digit “1’:when written in German, resembles
the digit
“7, However, the digit “7: when written in
German, always hasa horizontal line drawn rhrough it ,‘Z”).
4&17An example of how the above procedure should be
applied to calculate pinion depth using markings on
pinion is as follows:
1. Height block dimension
+ 1.4840.
2. Control figure (plus 10) converted to
f -.0039.
3. Difference between steps 1 and 2 it
1.4801.
4. Nominal figure
2 - 1.4680.
5. Shim thickness required
?r .0121.
6. Shim to closest thickness
+ .012.
4. Remove differential side bearing caps, gauging
arbor, gauge plate and pinion bearings.
5. Remove the rear pinion bearing outer race using
a brass drift.
6. Install pinion depth shims selected in Step
(f) in
the rear pinion bearing outer race bore and install the
rear pinion bearing outer race using installer J-78 18
and driver handle J-8092. See Figure 4B-18.
DRIVER.HANDLE
J-8092
48-12Figure 48.18 Installing Rear Pinion Bearing Outer
RaceI. Install rear pinion bearing onto the pinion using
installer J-21022. See Figure
4B-19.Figure 4B-19 Installing Rear Pinion Bearing
8. Lubricate pinion bearings and assemble the drive
pinion, collapsible spacer, front pinion bearing, oil
deflector plate and barrel spline sleeve in the differ-
ential carrier.
9. Thread barrel spline sleeve installer J-22938 onto
the drive pinion and draw the spline sleeve onto the
pinion until there are suflicient threads of the pinion

48. 16
1973 OPEL SERVICE MANUAL
protruding to install the pinion preload nut. Do
not use Installer J-22938 to adjust pinion preload.
See Figure 4B-20.
Assembly and Installation of Differential Case.
Opel 1900 and Manta1. Install side gears without thrust washers or shims.
BARREL SPLINE2. Lubricate and install pinion gears and thrust
washers between the side gears 180 degrees apart and
rotate the gears as an assembly until the pinion gear
bores are aligned with the pinion shaft bores in the
case.3. Install pinion shaft.
4. Install Special Tool J-24093 and, with the use of
a dial indicator, check end play clearance between
side gear and case as follows:
40-20a. Zero dial indicator on end of Tool J-24093. See
Figure 4B-22.
Figure 48.20 Installing Barrel Spline Sleeve
When the drive pinion end play is eliminated, the
preload specification is being approached. If this
specification is exceeded, replace the collapsible
spacer.10. Remove installer J-22938 and install washer and
pinion preload nut. Using Special Tool J-22932, hold
barrel spline and tighten preload nut until a preload
of 6-13
Ib.in. (9 Ibin. desired) with new bearings or
5-8
Ib.in. (6 lb.in. desired) with used bearings is re-
quired to rotate the drive pinion.
11. Use J-2293 1 to install a new pinion oil seal that
has been soaked in differential lubricant. See Figure4B-2
1.Figure 48.22 Zeroing Dial
lndicatotb. Using both hands, raise side gear until it bottoms
against case and record dial indicator reading. See
Figure 4B-23.
c. Measure the thickness of the concave thrust
washer by using a
0” to 1’ micrometer and subtract
this dimension from the dial indicator reading as
obtained in step b. Record dimension. See Figure
4B-24.
/INSTALLER J-22931d. After obtaining a dimension by subtracting con-48-21cave thrust washer thickness from dial indicator
reading, subtract an additional
,002 to obtain the
Figure 46.21 Installing Pinion Oil Sealcorrect shim thickness to be installed.

6. Before installing, shims must be measured to in-
sure that the proper thickness is being used. Install
shims of correct thickness to obtain desired clearance
and reassemble and install pinion shaft lock pin. In-
stall thrust washers with concave side towards differ-
ential case.
7. Using Special Tool J-24093, along with a foot-pound torque wrench, check torque to turn gears
using the following procedure:
a. Install axle shaft into a vise and position differen-
tial case onto axle shaft. See Figure
4B-25.Figure 48-23 Raising Side Gear Against Case
Figure 48.24 Measuring Concave Washer Thickness
AX,EXAMPLE:
1.Dial indicator reading * .095.
2. Subtract concave thrust washer thickness
+ -.oso.
3.Total + ,045.
4.Subtract an additional .002 *.002.
5. Shim thickness to be used
+ .043.
5. Turn case over and repeat the above procedure to
check other side gear to differential case clearance.Figure 48.25 Axle Shaft Installed in Vise
b. Insert Special Tool J-24093 into opposite side gear,
attach a torque wrench, and check torque to rotate
gear. S& Figure
4B-26. Permissible torque to turn
gears is 14
l/2 to 17 l/2 footpounds.
c. It is necessary to check rotating torque of both side
gears.8. If torque is not correct, it will be necessary to
reshim differential gears. Add first at one side one
shim of the next higher or lower thickness. If this is
not enough, reshim both sides completely.
9. Install ring gear on case making certain their mat-

48. 181973 OPEL SERVICE MANUAL
Figure 48.26 Checking Torque
to Rotate Gear
in;! surfaces are free of burrs or foreign material.
Tighten bolts to 47 lb.ft.
10. Check lateral runout of installed ring gear. Max-imum permissible runout is
.003”. If runout is
greater than specified, make certain that dirt or burrsare not holding the ring gear in a cocked position on
the case and that the bolts are evenly
torqued.Figure 48-27 Installing Differential Side Bearings
g. Install shim packs with respective side bearing1 I.
In.stall side bearings using installer J-22919 and
drive handle J-8092. Support opposite side of case on
pilot J-2241-1
1 to prevent bearing damage. See Fig-ure
4B-27.12. Determine differential side bearing preload and
backlash as follows:
a. Position differential case assembly less side bear-
ing shims into the side bearing bores of the carrier.
See Figure
4B-28.Figure 48.28 Installing Differential Case Assembly
b. Using two sets of feeler gauges, insert feeler stockof suffcent thickness between each bearing outer
race and the carrier to remove all end play. Make
certain the feeler stock is pushed to the bottom of thebearing bores. See Figure
4B-29.
c. Mount dial indicator J-8001 on carrier so indicator
stem is at right angles to a tooth on the ring gear. SeeFigure
4B-29.d. Adjust feeler gauge thickness from side to side
until ring gear backlash is ,004” to
.OO8” (.005” is
desired).e. With zero end play and correct backlash estab-
lished, remove feeler gauge packs, determine thick-
ness of shims required and add ,002” to each shim
pack to provide side bearing preload.
f. Remove case assembly and both side bearings us-ing J-22588 with adapter leg J-22939 and pilot
J-
2241-l 1.

REAR AXLE48.19FEELER
DIAL INDICATORDIFFERENTIAL
Figure 48.29 Removing Differential Case and End Playusing installer J-22919, driver handle J-8092 and pi-
lot J-2241-11.16. Install torque tube assembly.
17. Install axle shafts.
13. Position case assembly and outer races in the
carrier. Use a soft faced hammer to drive the case
into the carrier until the side bearing outer races
bottom in their bores.Assynbly and Installation of Differential Case
- GT
14. Install side bearing caps in their original location
and torque the bolts to 33
Ib.ft.
1. Lubricate the thrust washers, side and pinion gears
and install the side gears with respective thrust wash-
ers in the differential case.
15. Rotate case assembly several times to seat the
bearings. Check backlash and preload using a torque
wrench on a ring gear attaching bolt. See Figure
4B--68. Torque required to turn case should be 20 to 30
lb.in. for new bearings or 10 to 20 Ibin. for used
bearings. If torque is not correct, it will be necessary
to reshim the side bearings.2. Install the pinion gears and thrust washers be-tween the side gears 180 degrees apart and rotate the
gears as an assembly until the pinion gear bores are
aligned with pinion shaft bores in the case.
3. Install pinion shaft so that the lock pin hole in the
shaft aligns with the lock pin hole in the case.

49- 201973 OPEL SERVICE MANUAL
IN.LB. TORQUE
Figure 48.30 Checking Side Bearing Preload
4. With the use of a feeler gauge, check clearance
between differential side gears and case. See Figure
4B-31. Clearance should be ,003” to X106”. If clear-
ance is not within these limits, remove side gears and
install shims of correct thickness to obtain desired
clearance, reassemble and install pinion shaft lock
pin.
Figure 48.31 Checking Side Gear to Case Clearance
5. Install ring gear on case, making certain their
mating surfaces are free of burrs or foreign material.
Tighten bolts to 47
lb.ft.
6. Check lateral runout of installed ring gear. Max- imum permissible

runout is X03”. If runout is
greater than specified, make certain that dirt or burrs
are not holding the ring gear in a cocked position on
the case and that the bolts are evenly torqued.
7.
Imtall side bearings using Installer J-22919 and
Drive Handle J-8092. Support opposite side of case
on Pilot J-2241-1 1 to prevent bearing damage. See
Figure
4B-32.
DRIVER
HANDLE
J-8092
4B.27
Figure 48-32 Installing Differential Side Bearings
Figure
48.33 Installing Differential Case Assembly