1973 OPEL GT-R ECU

2F-281973 OPEL SERVICE MANUAL
guides to height adjustment rings, loosen second
screw (see Figure 2F-6), and swing guides away from
guide rail.
NOTE: When swinging front guides inboard, be
careful not to change position of height adjustment
rings. It is suggested that the position of the height
adjustment rings be marked with a pencil prior to
loosening of front guide attaching screws.
5. Retighten remaining screw holding front guide in
position to prevent height adjustment rings from
turning.
6. Turn lifter guide tension springs 90 degrees in-
board and pull lifters out of sun roof panel brackets
(see Figure
2F-7).Figure
ZF-7 Pulling Rear Lifter Guide out of Sun RoofPanel BracketNOTE: Do not loosen lifter pin nut as this will
change height adjustment on rear of sun roof.
7. Lift out sun roof panel.
Installation of Sun Roof Panel1. Install sun roof panel onto guide rails and locate
panel evenly in stin roof opening.
2. Reposition front guides in original position on
guide rails. Be sure that they squarely contact guide
rails and are not cocked.
NOTE: To achieve proper clearance of front guides
to guide rail, the guides should lightly touch edge ofdshould have a clearance of no
3. Reconnect
riar lifter guides onto sun roof panel
brackets and reposition tension spring as shown in
Figure
2F-3.4. Crank sun roof fully closed and check that the rear
lifters are at approximately 90 degrees with respect
to guide rails and contact guide stops (see Figure
2F-3). If adjustment is required remove crank handle
and cable crank (see Figure 2F-4) and physically
reposition lifters to position described above. Rotate
cable crank to its fully clockwise limit and reinstall.
5. Pull sun roof frame forward and reattach to sun
roof panel.
6. Open and close sun roof several times and recheck
for smoothness of operation.
Removal of Sunlpoof Frame1. Remove sun roof panel.
2. Crank rear lifter guides to furthermost rear posi-
tion.
3. Remove screws securing upper corner plates in
position and lift out upper corner plates (see Figure
2F-8).Figure 2F-&Removing Upper Corner Plates
4. Remove scretii securing left und
r@t guide rai1%lift up front ends
of- guide rails and msert wedge
under forward g&de rail ends. Slide out sun roof
frame.

ROOF AND SUN ROOF2F-29Installation of Sun Roof Frame1. Slide sun roof frame into lower slot of guide rails,
position fully rearward and reattach guide rails to
roof.NOTE: Be sure guide rail retainers at rear of guide
rails are positioned with their dowels in bores of roof
frame.2. Install upper corner plates and secure in place..
3. Install sun roof panel.
REMOVAL AND INSTALLATION OF VELVET STRIP
ON SUN ROOF OPENING, AND VELVET STRIP AND
WEATHERSTRIP ON REAR OF SUN ROOF PANEL
Removal of Velvet Strip on Sun Roof Opening1. Fully open sun roof.
;2. Carefully pull off velvet strip using solvent to dis-
solve cement. Clean area thoroughly before installing
new velvet strip.
Installation of Velvet Strip On Sun Roof Opening1. Cut away for a distance of 1.5 inch the velvet
material on velvet strip that will be on the outside
when strip is cemented in positioAlso cut off to
this dimension the plastic cord i
not cut away velvet material on
1strip which is to be cemented
2. Using
nitrile vinyl trim adhesive (3M Vinyl Trim
Adhesive, Permalastic Viny1 Trim Adhesive or
equivalent) apply sparingly to both sun roof opening
and side of velvet strip to be cemented.
3. Immediately install new velvet strip and position
so that upper edge of velvet strip is flush with car
roof.4. Clean off excess cement being careful not to con-
tact velvet strip.
Removal of Velvet Strip and Wea’therstrip on Rear
of Sun Roof Panel1. Remove sun roof panel.
2. Carefully detach weatherstrip and velvet strip
from sun roof panel using solvent as required todisdolve cement. Thoroughly clean area before in-
stalling new velvet strip and weatherstrip.
Installing Velvet Strip and Weatherstrip On Rear
of Sun Roof Panel1. Using
nitrile vinyl trim adhesive (3M Vinyl Trim
Adhesive Permalastic Viny1 Trim Adhesive or
equivalent) apply sparingly to vertical and horizontal
contact areas at rear of sun roof panel (see Figure
2F-9) and also to side of velvet strip which will touch sun
roof panel.
REAR OF SUN ROOF PANEL
ICAR ROOF
VELVET STRIP
II
,/ WETRSTRIP 1APPLY CEMENT TO HORIZONTAL AND
VERTICAL SURFACES,TO BOTH SIDES
OF VELVET STRIP AND TO SIDE AND
BOTTOM OF WEATHERSTRIP2F-9
Figure
ZF-9 Installing Velvet Strip and Weatherstrip
on Rear of Sun Roof Panel
2. Immediately install new velvet strip and position
so that top edge of velvet strip is flush with sun roof
panel.
3. Apply cement to outboard edge of velvet strip and
to top and bottom contact surfaces of weatherstrip,
and install weatherstrip in position.
4. Clean off excess cement being careful not to con-
tact velvet strip.
5. Install sun roof panel.
REMOVAL AND INSTALLATION OF REAR GUIDES
AND CABLE
Removal of Rear Guides and Cable
1. Remove sun roof panel.
2. Crank rear lifter guides fully rearward and then
remove crank handle and cable crank.

2F-321973 OPEL SERVICE MANUAL
3. Carefully detach a portion of headlining around
window corner post involved.
4. Detach water drain hose from sun roof hose iit-
ting.
5. Remove cowl side kickpads.
6. Pull out from upper end front water drain hose.
Installation of Front Water Drain Hose
1. Insert from above water drain hose (wider end
upward) into door hinge pillar.
NOTE: Do not mistake front and rear water hoses.
The front hose is thinner than the rear hose and is
wider at the end which connects to hose fitting on
sun roof. The rear hose is uniform over its entire
length.
2. Work water drain hose downward through lower
half of door hinge pillar and be sure hose terminates
behind door sill flange at bottom of frbnt fender.
3. Cement upper portion of water drain hose to sun
roof hose fitting.
4. Cement detached portions of headlining into place
by use of rubber cement or nitrile vinyl trim adhesive
(3M Vinyl Trim Adhesive, Permalastic Vinyl Trim
Adhesive or equivalent).
5. Complete installation reverse of removal proce-
dures.
Removal of Rear Water Drain Hose1. Remove rear seat and rear seat back.2. Pry out plastic fasteners securing cardboard parcel
shelf in position and remove shelf.
3. Remove rear quarter trim pad.
4. Detach headlining only as required from area
around rear window pillar.
5. Pull out rear water drain hose.
Installation of Rear Water Drain Hose1. Install rear water drain hose in original position.
Insert hose from above and work downward. Ce-
ment both ends of hose in place.
2. Secure water drain hose in place along wheel-
house.3. Complete installation reverse of removal proce-
dures.
REMOVAL AND INSTALLATION
OF LUGGAGE
RACKAll 1973 luggage racks will be dealer installed, and
are held to the roof at the 4 corners. Removal and
installation is accomplished by removing the attach-
ing screw at each corner. See Figure
2F-14.Figure ZF-14 Luggage Rack

SEATS, INTERIOR TRIM AND HEADLININGZG-35
2. Push off side panel trim pad. Trim pad is held in
position by a retaining button.
REMOVAL AND INSTALLATIONOF HEADLINING
Removal
1. Disconnect battery.
2. Lift out rear seat cushion (sedans only).
3. From trunk area, loosen tabs holding cardboard
against rear seat cross brace and lift out cardboard
(sedans only).
4. Pry up two tabs holding lower portion of rear seat
back in position, swing back of seat forward and lift
out (sedans only).
5. From trunk area pry out parcel shelf plastic retain-
ers and lift out parcel shelf (sedans only).
6. Remove rear-view mirror, sun visors, interior
lamp, assist straps and coat hooks. Remove front and
rear windows on all but Wagon Models. On Wagons,
remove the front window and the quarter windows.
7. Work door opening pinchweld finishing strip
away from pinchweld as far as necessary to expose
edge of headlining.
8. Start at: left or right windshield pillar and pry
headlining loose.
9. Roll back headlining to expose metal tabs securing
headlining listing wire to roof and unhook headhn-
ing front listing wire from metal tabs using a blunt
edge tool.
10. Pull loose the edges of headlining cemented to
door openings, rear quarter window openings, rear
quarter pillar and from under rear window rubber
channel. On rear quarter pillars, slightly bend down
cardboard of rear quarter trim pad to facilitate re-
moval. During removal, special care should be taken
not to tear headlining at seams.
11. After edges of headlining have been pulled loose,
tilt remaining listing wires with headlining forward
or rearward and pull listing wires free from side roof
rails. Lift out headlining and listing wires.
Installation1. Check secureness of noise insulation pad on inside
of roof panel and recement as necessary using asphalt
cement. If headlining is to be replaced, insert listing
wires into headlining according to their markings.
Progressing from the front listing wire to the rear
wire, the left ends of the wires are color coded as
follows:1st listing wire
- No marking, wire is thinner than
other wires
2nd listing wire
- Red
3rd listing wire
- Blue
4th listing wire
_ Green
5th listing wire
- Brown
6th listing wire
- White
2. Install 1st listing wire ends into retainer slots in-
side roof rails and hook listing wire into six metal
tabs above windshield. Lightly bend tabs with a ham-
mer as shown in Figure
2G-8.
HEAOLlN’lNdA-----
26-8Figure
2G-8 Headlining With 1st Listing Wire Hooked
Onto Metal Tabs
LISTINGWIRE
SECTIOND-D
4 26-9Figure 2G-9 2nd and 5th Listing Wire Attachment

2H-381973 OPEL SERVICE MANUAL
BUMPERS
CONTENTS
Subject
DESCRIPTION AND OPERATION: Protective Moldings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . *. . . . . . . . . . . . . . . . .
DIAGNOSIS: (Not Applicable)
MAINTENANCE AND ADJUSTMENTS: (Not
Applicable) MAJOR REPAIR: Removal and Installation
1900
- Manta. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GT. . . . . . . . . . . . . . . . . . . . . . . . . . . * . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . . . . . . . . . . . . . . . . . . . .
Trailer Hitch Installation, . , . . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . .
SPECIFICATIONS: (Not Applicable) Page No.
2H-38
2H-38
2H-39
2H-41
DESCRIPTION ‘AND OPERATION
PROTECTIVE MOLDINGS
All 1973 Opel bumpers are equipped with rubber
protective moldings as standard equipment. The
moldings are easily removed by removing the attach-
ing nuts located on the inboard side of the bumper.
MAJOR REPAIR
REMOVAL AND INSTALLATION OF FRONT
BUMPER AND BUMPER GUARDS
(OPEL 1900 -
MANTA)
Removal
1. Remove bumper attaching screws on inside
- left
and right
- and from left and right brackets. See
Figure
2H-2.
2. From the front, unscrew bumper guard attaching
screws. See Figure‘
2H-2.
Remove bumper and bumper guards.
Installation
1. Attach bumper guards to bumper.
Figure ZH-2 Bumper Attaching Screws
2. From the front, secure bumper guards with attach-
ing screws. See Figure
2H-2.
3. Install attaching bolts on left and right brackets,
and on left and right inside. See Figure
2H-2.
REMOVAL AND INSTALLATION OF FRONT
BUMPER BRACKETS (OPEL 1900
- MANTA)
The front bumper brackets are attached with three
screws. Removal of the three screws will allow re- moval and installation of the front bumper brackets.
See Figure
2H-3.
REMOVAL AND INSTALLATION OF REAR
BUMPER AND GUARDS (OPEL 1900
- MANTA)
1. Remove license plate lamp.
2. Remove bumper attaching screws and bumper
brackets. See Figure
2H-4.

BUMPERS21-1-39--..,2H-3 i
Figure ZH-3 Bumper Bracket Screws
Figure ZH-4 Bumper Attaching ScrewsREMOVAL AND INSTALLATION OF FRONT REMOVAL AND INSTALLATION OF FRONT
BUMPER ASSEMBLY
(GT)BUMPER ASSEMBLY (GT)1. Remove grille. 1. Remove grille.
2. Disconnect bumper at points shown in Figure2H-5 and remove bumper. 2. Disconnect bumper at points shown in Figure2H-5 and remove bumper.
Installation
Installation1. Install bumper and secure at points shown in Fig-
ure 2H-5. 1. Install bumper and secure at points shown in Fig-
ure 2H-5.
RemovalFigure ZH-6 Removing Tail Lamp Assembly
Figure 2H-5 Front Bumper Attaching Points
Figure 2H-7 Rear Bumper Attaching Points

z-l-401973 OPEL SERVICE MANUAL
2. Install grille.
REMOVAL AND INSTALLATION OF REAR
BUMPER ASSEMBLY (GT)
Removal1. Remove tail lamp assembly. See Figure 2H-6.2. Remove bumper attaching nuts accessible through
lamp opening. See Figure 2H-7.Installation1. Install bumper and secure with attaching nuts
accessible through lamp opening. See Figure 2H-7.
2. Install tail lamp assembly. See Figure 2H-6.

STEERING LINKAGE38.19STEERING LINKAGE
CONTENTS
Subject
DESCRIPTION AND OPERATION:
Description
andOperationofTieRods. . . . . . . . . . . . . . . . . . . . . .DIAGNOSIS: (Not Applicable)
MAINTENANCE AND ADJUSTMENTS: (Not
Applicable)
MAJOR REPAIR:
RemovalandInstallationofTieRods. . . . . . . . . . . . . . . . . . . . . . . .Disassembly
andReassemblyofTieRods. . . . . . . . . . . . . . . .SPECIFICATIONS:
Tightening Specifications ..,.............................................Page No.
38-193B-1938-21jB-21
DESCRIPTION AND OPERATION2. Using remover J-21687, pull outer tie rod ball
studs out of steering arms. See Figure
3B-2.DESCRIPTION AND OPERATION OF TIE RODS
Tie rods on the GT are connected to both rack ends
by means of a ball joint. Two rubber bellows between
ball joint and steering gear housing protect rack and
ball joints against dirt, dust and mud. The ball joints
of the tie rods do not require service.
Tie rods on the Opel l&O and Manta are connected
to both rack ends by means of a axial joint. Two
rubber bellows between the axial joint and steering
gear housing protect the rack and axial joints against
dirt, dust, and mud. The ball joint of the tie rod ends
on the Opel 1900 and Manta are maintenance free
and must not be disassembled.
MAJOR REPAIRREMOVAL AND INSTALLATION OF TIE RODS
38-2
RemovalFigure
38-2 Removing Ball Stud
In order to avoid the possibility of dirt entering the
steering gear assembly via the rack, it is recom-
mended that rods and area immediately surrounding
the gear assembly be wiped free of loose dirt prior to
removal.3. Remove clamp securing one end of rubber bellows
to tie rods and slip bellows off tie rods to expose nut
or lock plates. See Figure
3B-3.1. Remove cotter pins securing nuts on tie rod ends
and remove nuts. Discard cotter pins.4. On the GT, bend up round edges of lock plate
from tie rod ball studs and unscrew ball studs From
rack. See Figure
3B-4.