1969 FORD MUSTANG oil

07-01-02

General Transmission Service

07-01-02

COMPONENT INDEX

FLUID LEAKAGE CHECK

FLUID LEVEL CHECK

FRONT CLUTCH (Forward) INSPECTION

C4 Transmission

C6 Transmission

FMX Transmission

FRONT PUMP AND STATOR SUPPORT

Inspection

FRONT SERVO (Intermediate) INSPECTION

C4 Transmission

C6 Transmission

FMX Transmission

GOVERNOR INSPECTION

HYDRAULIC SYSTEM BENCH TESTS

(FMX)

Pressure Tests

Testing Tool Installation

MANUAL LINKAGE CHECKS

MANUAL SHIFT LINKAGE GROMMET

COLUMN SHIFT

Removal and Installation

NEUTRAL START SWITCH-COLUMN

SHIFT

Adjustment

Removal and Installation

OIL COOLER CLEANING

OIL COOLER TUBES

Removal and Installation

ONE-WAY CLUTCH INSPECTION

OUTPUT SHAFT AND PRIMARY SUN

GEAR

Shaft (FMX)

Inspection

PINION CARRIER, ONE-WAY CLUTCH

AND CENTER SUPPORT (FMX)

Inspection

PINION CARRIERS INSPECTION

C4 Transmission

C6 Transmission

PRESSURE REGULATOR (FMX)

Inspection

REAR CLUTCH (Reverse-High) INSPECTION

C4 Transmission

C6 Transmission

FMX Transmission

REAR SERVO (Low-Reverse) INSPECTION

C4 Transmission
MODEL APPLICATION
All
Models

01-03

01-03

01-16

01-17

01-04

01-11

01-08

01-17
Ford
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Mercury
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A
Meteor
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Cougar
N/A

01-16

01-16

N/A

01-17

01-17

01-08

01-07

N/A

N/A

N/A

01-12

01-15

N/A

01-15

01-17

N/A

01-16

01-16

N/A

01-17
Fairlane
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Falcon
01-16

N/A

N/A

01-17

N/A

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

01-17

N/A
Montego
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Mustang
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

N/A

N/A

N/A

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Lincoln-
Continental
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A
Thunderbird
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A
Continental-
Mark
III
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.
procarmanuals.com

07-01-03

General Transmission Service

07-01-03

COMPONENT INDEX

FMX Transmission

REAR SUPPORT (FMX)

Inspection

SHIFT POINT CHECKS

STATOR ONE-WAY CLUTCH CHECK

STATOR TO IMPELLOR INTERFERENCE

CHECK

STATOR TO TURBINE INTERFERENCE

CHECK

TRANSMISSION CLEANING

TURBINE AND STATOR END PLAY

CHECK

VACUUM DIAPHRAGM ADJUSTMENT

Altitude Compensating Type

Non-Altitude Compensating Type

VACUUM UNIT CHECK

Altitude Compensating Type

Non-Altitude Compensating Type
MODEL APPLICATION
All
Models

01-06

01-12

01-12

01-12

01-11

01-12
Ford
01-17

01-16

N/A

01-08

N/A

01-05
Mercury
N/A

N/A

N/A

01-08

N/A

01-05
Meteor
01-17

01-16

N/A

01-08

N/A

01-05
Cougar
01-17

01-16

N/A

01-08

N/A

01-05
Fairlane
01-17

01-16

N/A

01-08

N/A

01-05
Falcon
N/A

N/A

N/A

01-08

N/A

01-05
Montego
01-17

01-16

N/A

01-08

N/A

01-05
Mustang
01-17

01-16

N/A

01-08

N/A

01-05
Lincoln-
Continental
N/A

N/A

01-09

N/A

01-06

N/A
Thunderbird
N/A

N/A

01-09

N/A

01-06

N/A
Continental-
Mark
III
N/A

N/A

01-09

N/A

01-06

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

Three different three-speed trans-

missions are used. The C4 Automatic,

C6 Automatic and the FMX Auto-

matic. Part 7-1 covers testing, com-
mon adjustments and repairs, and

cleaning and inspection for the three

types of transmissions. Where there
are differences in procedures or speci-

fications, the type of transmission af-

fected will be designated.

l
AUTOMATIC TRANSMISSION TESTS

When diagnosing transmission

problems, refer to the Ford Car and

Truck Diagnosis Manual for the de-

tailed information on the items that

could be causing the problem.

The following preliminary checks

should be made before proceeding

with other diagnosis checks.

TRANSMISSION FLUID LEVEL

CHECK

1.
Make sure that the vehicle is

standing level. Then firmly apply the

parking brake.

2.
Run the engine at normal idle

speed. If the transmission fluid is cold

run the engine at fast idle speed

(about 1200 rpm) until the fluid reach-

es its normal operating temperature.

When the fluid is warm, slow the en-

gine down to normal idle speed.

3.
On a vehicle equipped with a

vacuum brake release, disconnect the

release line and plug the end of the
line;
otherwise the parking brake will

not hold the transmission in any drive

position.

4.
Shift the selector lever through

all positions, and place the lever at P.

Do not turn off the engine during the

fluid level checks.

5.
Clean all dirt from the transmis-

sion fluid dipstick cap before remov-

ing the dipstick from the filler tube.

6. Pull the dipstick out of the tube,

wipe it clean, and push it all the way

back into the tube. Be sure it is prop-

erly seated.

7.
Pull the dipstick out of the tube

again, and check the fluid level. The

fluid level should be above the ADD

mark. If necessary, add enough fluid

to the transmission through the filler

tube to bring the level between the

ADD and FULL marks on the dip-

stick. Do not overfill the transmission.

Install the dipstick, making sure it is

fully seated in the tube.
8. Connect the vacuum brake re-

lease line if so equipped, and test it

for proper operation.

FLUID AERATION CHECK

A fluid level that is too high will

cause the fluid to become aerated:

Aerated fluid will cause low control

pressure, and the aerated fluid may be

forced out the vent.

Check the transmission fluid level.

Low fluid level can affect the opera-

tion of the transmission, and may in-

dicate fluid leaks that could cause

transmission damage.

TRANSMISSION FLUID

LEAKAGE CHECKS

Check the speedometer cable con-

nection at the transmission. Replace

the rubber seal if necessary.

Leakage at the oil pan gasket often

can be stopped by tightening the at-
procarmanuals.com

07-01-04
General Transmission Service

07-01-04

taching bolts to the proper torque. If

necessary, replace the gasket.

Check the fluid filler tube connec-

tion at the transmission case or pan.

If leakage is found here, install a new

O-ring or tighten the fitting to the

specified torque.

Check the fluid lines and fittings

between the transmission and the

cooler in the radiator tank for loose-

ness,
wear, or damage. If leakage can-

not be stopped by tightening a fitting,

replace the damaged parts.

Check the engine coolant in the ra-

diator. If transmission fluid is present

in the coolant, the cooler in the radia-

tor is probably leaking.

The cooler can be further checked

for leaks by disconnecting the lines

from the cooler fittings and applying

50-75 psi air pressure to the fittings.

Remove the radiator cap to relieve the

pressure build at the exterior of the oil

cooler tank. If the cooler is leaking

and will not hold this pressure the

cooler must be replaced. Cooler re-

placement is described in the Cooling

System Section of Group 11.

If leakage is found at either the

downshift control lever shaft or the

manual lever shaft, replace either or

both seals.

Inspect the pipe plug on the left

side of the transmission case at the

front. If the plug shows leakage, tor-

que the plug to specifications. If tight-

ening does not stop the leaks, replace

the plug. On a C6 transmission, a TV

pressure plug is also provided on the

right rear side of the case.

When converter drain plugs leak,

remove drain plugs with a six-point

wrench. Coat the threads with FoMo-

Co Perfect Seal Sealing Compound or

its equivalent, and install the plugs.

Torque the drain plugs to specifica-

tion. Fluid leakage from the converter

housing may be caused by engine oil

leaking past the rear main bearing or

from oil gallery plugs, or power steer-

ing oil leakage from steering system.

Be sure to determine the exact cause

of the leak before repair procedures

are started.

Oil-soluble aniline or fluorescent dyes

premixed at the rate of 1/2 teaspoon

of dye powder to 1/2 pint of transmis-

sion fluid have proved helpful in locat-

ing the source of the fluid leakage.

Such dyes may be used to determine

whether an engine oil or transmission

fluid leak is present or if the fluid in

the oil cooler leaks into the engine

coolant system. A black light, how-

ever, must be used with the fluorescent

dye solution.
DISHED OR

FLAT WASHER

" O.D.,
a" STEEL PLATE

5/8"X \W,

DRILL TO SUIT
HEX. HEAD SCREW

3/8"-24 X Vl

HEX. NUT W—
24

WELD

TOGETHER

WING
NUT

>/2"_13
THREAD

CHAIN,
10"
LONG
RUBBER PLUG

1
Vi" DIA. X 2"

LONG Vl"

HOLE THRU

APPROXIMATELY

40 DUROMETER
FLAT WASHER

Vs" O.D.

PLUG

VALVE
STANDARD BOLT

W-13
X 4Vl"

LONG SQUARE

THREAD
END

REMOVE HEAD

AND WELD
TO

WASHER

STANDARD 1/8" FITTING-87971-S FOR

RETAPPED DRAIN PLUG THREADS-USE

1/4" OVERSIZE FITTING-87973-S

D 1067-B
WELD TOGETHER

SECURELY—MUST

NOT LEAK

FIG. 2—Converter Leak Checking Tool

CONVERTER LEAKAGE

CHECK

If there are indications that the

welds on the torque converter are

leaking, the converter will have to be

removed and the following check

made before the unit is replaced.

A leak checking tool (Fig. 2) can be

made from standard parts. The tool

can be used to check all converters.

1.
Install the plug in the converter

(Fig. 3) and expand it by tightening

the wing nut. Attach the safety chains.

2.
Install the air valve in one of the

drain plug holes.

3.
Introduce air pressure into the

converter. Check the pressure with a

tire gauge and adjust it to 20 psi.

4.
Place the converter in a tank of

water. Observe the weld areas for

bubbles. If no bubbles are observed, it

may be assumed that the welds are

not leaking.

ENGINE IDLE SPEED CHECK

Check and, if necessary, adjust the

engine idle speed, using the procedure

given in Group 10.

If the idle speed is too low, the en-

gine will run roughly. An idle speed

that is too high will cause the vehicle

to creep, have harsh engagements and

harsh closed-throttle downshifts.
ANTI-STALL DASHPOT

CLEARANCE CHECK

After the engine idle speed has been

properly adjusted, check the anti-stall

dashpot clearance. Follow the proce-

dure given in Group 10 for checking

and adjusting this clearance.

MANUAL LINKAGE CHECKS

Correct manual linkage adjustment

is necessary to position the manual

valve for proper fluid pressure direc-

tion to the different transmission com-

ponents. Improperly adjusted manual

Tire Pressure Gauge

D1921-A

FIG. 3—Converter Leak Checking

Tool Installationprocarmanuals.com

07-01-06
General Transmission Service

07-01-06

MAKE MARK HERE

BELLOWS INTACT
BELLOWS FAILED

FIG. 9—Checking Vacuum Unit Bellows

tester equipped with a vacuum pump

(Fig. 8). Set the regulator knob so

that the vacuum gauge reads 18 inches

with the end of the vacuum hose

blocked off.

Then connect the vacuum hose to

the transmission vacuum unit. If the

gauge still reads 18 inches, the vacuT

urn unit diaphragm is not leaking. As

the hose is removed from the trans-

mission vacuum unit, hold a finger

over the end of the control rod. When

the hose is removed, the internal

spring of the vacuum unit should push

the control rod outward.

ALTITUDE

COMPENSATING-TYPE

The vacuum diaphragm should be

checked for ruptured or damaged bel-

lows.
Check the diaphragm assembly

as follows:

1.
Remove the diaphragm and

throttle valve rod from the transmis-

sion.

2.
Insert a rod into the diaphragm,

making sure that the rod is buttonec

in the hole. Make a reference mark on

the rod where it enters the diaphragm

hole.

3.
Hold the assembly in such a way

that the end of the rod is resting on

the weighing surface of a scale (Fig.

9).

4.
Gradually press down on the dia-

phragm assembly until the rod is

pressed into the diaphragm body. If

the reference mark on the rod is still
visible with 12 pounds of force regis-

tered on the scale, the bellows are in-

tact. If the mark disappears before 4

pounds of force is exerted, the bellows

have failed and the diaphragm must

be replaced. If the bellows are intact,

then perform various pressure checks.

SHIFT POINT CHECKS

Check the minimum throttle up-

shifts in D. The transmission should

start in first gear, shift to second, and

then shift to third, within the shift

points specified in the specification

section.

While the transmission is in third

gear, depress the accelerator pedal

through the detent (to the floor). The

transmission should shift from third to

second or third to first, depending on

the vehicle speed.

Check the closed throttle downshift

from third to first by coasting down

from about 30 mph in third gear. The

shift should occur within the limits

specified in the specification section.

When the selector lever is at 2, the

transmission can operate only in sec-

ond gear.

With the transmission in third gear

and road speed over 30 mph, the

transmission should shift to second

gear when the selector lever is moved

from D to 2 to 1. The transmission

will downshift from second or third to

first gear when this same manual shift

is made below approximately 25 mph

with a C4 transmission, 30 mph with
D 1791.A

a C6 transmission or 35 mph with an

FMX transmission. This check will

determine if the governor pressure and

shift control valves are functioning

properly.

During the shift point check opera-

tion, if the transmission does not shift

within specifications or certain gear

ratios cannot be obtained, refer to the

Ford Car and Truck Diagnosis Manu-

al to resolve the problem.

AIR PRESSURE CHECKS

A NO DRIVE condition can exist,

even with correct transmission fluid

pressure, because of inoperative

clutches or bands. Erratic shifts could

be caused by a stuck governor valve.

The inoperative units can be located

through a series of checks by subst-

ituting air pressure for the fluid pres-

sure to determine the location of the

malfunction.

To make the air pressure checks,

drain the transmission fluid and re-

move the oil pan and the control valve

body assembly. The inoperative units

can be located by introducing air pres-

sure into the transmission case passa-

ges leading to the clutches, servos, and

governor (Figs. 10, 11 or 12).

HYDRAULIC SYSTEM BENCH

TESTS (FMX TRANSMISSION)

After the transmission has been as-

sembled and is ready for installationprocarmanuals.com

07-01-08
General Transmission Service

07-01-08

3.
Install the bench testing tool on

the transmission.

4.
Remove the
1/8-inch
pipe plug

at the transmission case. Turn the

front pump in a clockwise direction at

75-100 rpm until a regular flow of

transmission fluid leaves the hole in

the transmission case. This operation
bleeds the air from the pump.

5.
Install the pressure gauge (77820

or T57L-77820-A) as shown in Fig.

13.

PRESSURE TESTS

Turn the front pump at 75-100 rpm
and note the gauge readings. The

pressure readings on the bench test

must be within the limits as outlined

in Figure 13, for the engine idle check.

If pressure gauge readings are with-

in limits in all selector lever positions,

install the vacuum diaphragm control

rod unit.

COMMON ADJUSTMENTS AND REPAIRS

TRANSMISSION FLUID DRAIN

AND REFILL

Normal maintenance and lubrica-

tion requirements do not necessitate

periodic automatic transmission fluid

changes.

If a major repair, such as a clutch

band, bearing, etc., is required in the

transmission, it will have to be re-

moved for service. At this time the

converter, transmission cooler and

cooler lines must be thoroughly

flushed to remove any dirt.

When filling a dry transmission and

converter, install five quarts of fluid.

Start the engine, shift the selector

lever as outlined below, and check and

add fluid as necessary.

Following are the procedures for

partial drain and refill due to in-

vehicle repair operation.

C4 TRANSMISSION

1.
On PEA models, disconnect the

fluid filler tube from the transmission

oil pan to drain the fluid.

On PEB and PEE models, loosen

the pan attaching bolts to drain the

fluid from the transmission.

2.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

3.
Place a new gasket on the pan,

and install the pan on the transmis-

sion.

4.
On PEA models, connect the

filler tube to the pan and tighten the

fitting securely.

5.
Add three quarts of fluid to the

transmission through the filler tube.

6. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches it's normal operating temp-

erature. Do not race the engine.

7.
Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If
necessary, add enough fluid io the

transmission to bring the level be-

tween the ADD and FULL marks on

che dipstick. Do not overfill the trans-

mission.

FMX OK C6

TRANSMISSION

1.
Raise the vehicle on a hoist or

jack stands.

2.
Place a drain pan under the

transmission.

3.
Loosen the pan attaching bolts

to drain the fluid from the transmis-

sion.

4.
After the fluid has drained to the

level of the pan flange, remove the

rest of the pan bolts working from the

rear and both sides of the pan to

allow it to drop and drain slowly.

5.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

6. Place a new gasket on the pan,

and install the pan on the transmis-

sion.

7.
Add three quarts of fluid to the

transmission through the filler tube.

8. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches normal operating tempera-

ture.
Do not race the engine.

9. Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If

necessary, add enough fluid to the

transmission to bring the level be-

tween the ADD and FULL marks on

the dipstick. Do not overfill the trans-

mission.

OIL COOLER TUBE

REMOVAL AND INSTALLATION

When fluid leakage is found at the

oil cooler, the cooler must be re-

placed. Cooler replacement is de-

scribed in the Cooling System Section

of Group 11.
When one or more of the fluid

cooler steel tubes must be replaced,

each replacement tube must be fabri-

cated from the same size steel tubing

as the original line.

Using the old tube as a guide, bend

the new tube as required. Add the

necessary fittings, and install the tube.

After the fittings have been tight-

ened, add fluid as needed, and check

for fluid leaks.

VACUUM DIAPHRAGM

ADJUSTMENT NON-ALTITUDE

COMPENSATING TYPE

The C4 and C6 transmissions are

equipped with an adjustable vacuum

diaphragm assembly. A similar ad-

justable diaphragm has been released

for service with the FMX transmis-

sion. However, the FMX service dia-

phragm is not interchangeable with

that used on C4 and C6 models.

The vacuum diaphragm assembly

has an adjusting screw in the vacuum

hose connecting tube (Fig. 14).

SPRING

SEAT

THIS CLEARANCE CHANGED

BY ADJUSTING SCREW

D1830-A

FIG. 14—Adjustable Vacuum Unit

The inner end of the screw bears

against a plate which in turn bears

against the vacuum diaphragm spring.

All readings slightly high or all

readings slightly low may indicate the

vacuum unit needs adjustment to cor-

rect a particular shift condition.procarmanuals.com

07-01-11
General Transmission Service

07-01-11

STOP
PIN

GROMMET

Tool - T67P-734LA

GROMMET

LEVER

CONTROL ROD REMOVAL
GROMMET INSTALLATION

Tool - T67P-734LA

r

CONTROL ROD INSTALLATION
3/16"-1/4'

CONTROL ROD

STOP
PIN

FIG. 18—Removing
or
Installing Shift Linkage Grommet
D 1742-A

MANUAL SHIFT LINKAGE

GROMMET REPLACEMENT-

COLUMN SHIFT

The manual lever assembly
on ve-

hicles equipped with
a
column shift
in-

corporates
an oil
impregnated plastic

grommet
in the end of the
lever
arm.

A special tool T67P-7341-A
is re-

quired
to
install
the
grommet
in the

manual lever,
and to
install
the
manu-

al linkage
rod
into
the
grommet.
Re-

move
and
install
the
grommet
as fol-

lows:

1.
Place
the
lower
jaw of the
tool

between
the
manual lever
and the con-

trol
rod.
Position
the
stop
pin
against
the
end of the
control
rod (Fig. 18)

and force
the rod out of the
grommet.

Remove
the
grommet from
the
manu-

al lever
by
cutting
off the
large shoul-

der with
a
sharp knife.
The
grommet

must
be
removed from
the
manual

lever
and a new one
installed each

time
the rod is
disconnected.

2.
Before installing
a
new grommet,

adjust
the
stop
pin to 1/2
inch
and

coat
the
outside
of the
grommet with

lubricant. Then, place
the
grommet
on

the stop
pin and
force
it
into
the
man-

ual lever hole. Turn
the
grommet
sev-

eral times
to be
sure
it is
properly

seated.

3.
Readjust
the
stop
pin to the
height shown
in Fig. 18. The pin

height
is
determined
by the
length
of

the
rod end
which
is to be
installed

into
the
grommet.
If the pin
height
is

not adjusted,
the
control
rod may be

pushed
too far
through
the
grommet

causing damage
to the
grommet
re-

taining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
control
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of the
grom-

met.
Be
sure
the rod
protrudes

through
the
grommet approximately

1/4 inch after installation.

CLEANING
AND
INSPECTION

CLEANING

TRANSMISSION

Clean
the
parts with suitable solvent

and
use
moisture-free
air to dry off all

the parts
and
clean
out oil
passages.

The composition clutch plates,

bands
and
synthetic seals should
not

be cleaned
in a
vapor degreaser
or
with
any
type
of
detergent solution.

To clean these parts, wipe them
off

with
a
lint-free cloth.
New
clutch

plates
or
bands should
be
soaked
in

transmission fluid
for
fifteen minutes

before
the
plates
or
bands
are as-

sembled.

CONVERTER

The converter cannot
be
disas-

sembled
for
cleaning.
If
there
is rea-
son
to
believe that
the
converter
con-

tains
an
excessive amount
of
foreign

material,
it
should
be
thoroughly

cleaned.
See the
instructions provided

with
the
Rotunda Automatic Trans-

mission Torque Converter
and
Cooler

Cleaner LRE-60081.

OIL COOLER

When
a
clutch
or
band failure
or

other internal trouble
has
occurred
inprocarmanuals.com

07-01-12
General Transmission Service

07-01-12

the transmission,
any
metal particles

or clutch plate
or
band material that

may have been carried into
the
cooler

should
be
removed from
the
system
by

flushing
the
cooler
and
lines before

the transmission
is put
back into serv-

ice.
In no
case should
an
automatic

transmission having
a
clutch
or
band

failure
or
other internal trouble result-

ing
in
fluid contamination,
be put

back into service without first flushing

the transmission
oil
cooler.

To flush
the oil
cooler, follow
the

instruct!
on >
provided with
the
Rotun-

da Automatic Transmission Torque

Converter
and
Cooler Cleaner
LRE-

60081.

INSPECTION

TURBINE
AND
STATOR
END

PLAY CHECK

A special tool
(Fig. 19)
must
be

used
to
check
the
condition
of the

converter. This special tool
is
used
to

check
the
turbine
and
stator
end
play

and
the
operation
of the
one-way
sta-

tor clutch.

CRUISE-O-MATIC

Too/-T58L-7902-A

C-4 AND C-6 TRANSMISSION

Tool-T59P.7902.Bor 7937-B

ON C-4 AND C-6 TRANSMISSION

Tool-T64L-7902-A
D
1499-E

FIG. 19—Converter Checking Tool

1.
Insert
the
tool (Fig.
19)
into
the

converter pump drive
hub
until
it
bot-

toms.

2.
Install
the
guide over
the con-

verter pump drive
hub.
3.
Expand
the
split fiber bushing
in

the turbine spline
by
tightening
the

adjusting
nut.
Tighten
the
adjusting

nut until
the
tool
is
securely locked

into
the
spline.

4.
Attach
a
dial indicator
to the

tool (Fig.
20 or
21). Position
the
indi-

cator button
on a
converter pump

drive
hub, and set the
dial face
at 0

(zero).

5.
Lift
the
tool upward
as far as it

will
go and
note
the
indicator reading.

The indicator reading
is the
total
end

play which
the
turbine
and
stator

share.
If the
total
end
play exceeds

the limits specified
in
Part 7-5, replace

the converter unit.

6. Loosen
the
adjusting
nut to
free

the split bushing,
and
then remove
the

tool from
the
converter.

STATOR ONE-WAY CLUTCH

CHECK

1.
Install
the
stator outer race hold-

ing tool
in one of the
four holes
pro-

vided
in the
stator (Fig.
20 or 21).

2.
Insert
the
tool
in the
converter

pump drive hub.
As the
tool enters
the

converter,
the
pins will engage
the sta-

tor clutch inner race spline.

3.
Place
a
torque wrench
on the

tool (Fig.
20 or
21).
The
tool (and
sta-

tor inner race) should turn freely

clockwise (from
the
pump drive
hub

inside
the
converter).
It
should lock
up

and hold
a 10
ft-lb pull when
the

wrench
is
turned counterclockwise.

Try
the
clutch
for
lockup
and
hold
in

at least five different locations around

the converter.
On
the
C4
or C6
Auto-

matics,
the
metal ring holding
the

locking tool will have
to be
held
by

hand during this check.

4.
If the
clutch fails
to
lock
up and

hold
a 10
ft-lb torque, replace
the

converter unit.

STATOR
TO
IMPELLER

INTERFERENCE CHECK

1.
Position
the
front pump assem-

bly
on a
bench with
the
spline
end of

the stator shaft pointing
up
(Fig.
22).

2.
Mount
a
converter
on the
pump

so that
the
splines
on the
one-way

clutch inner race engage
the
mating

splines
of the
stator support,
and the

converter
hub
engages
the
pump drive

gear.

3.
While holding
the
pump station-

ary, try
to
rotate the converter counter-

clockwise.
The
converter should
ro-

tate freely without
any
signs
of
inter-

ference
or
scraping within
the
convert-

er assembly.
4.
If
there
is an
indication
of
scrap-

ing,
the
trailing edges
of the
stator

blades
may be
interfering with
the

leading edges
of the
impeller blades.

In such cases, replace
the
converter.

STATOR
TO
TURBINE

INTERFERENCE CHECK

1.
Position
the
converter
on the

bench front side down.

2.
Install
a
front pump assembly
to

engage
the
mating splines
of
the
stator

support
and
stator,
and
pump drive

gear lugs.

3.
Install
the
input shaft, engaging

the splines with
the
turbine
hub (Fig.

23).

4.
While holding
the
pump station-

ary, attempt
to
rotate
the
turbine with

the input shaft.
The
turbine should
ro-

tate freely
in
both directions without

any signs
of
interference
or
scraping

noise.

5.
If
interference exists,
the
stator

front thrust washer
may be
worn,
al-

lowing
the
stator
to hit the
turbine.
In

such cases,
the
converter must
be re-

placed.

The converter crankshaft pilot

should
be
checked
for
nicks
or dam-

aged surfaces that could cause inter-

ference when installing
the
converter

into
the
crankshaft. Check
the con-

verter front pump drive
hub for
nicks

or sharp edges that would damage
the

pump seal.

OUTPUT SHAFT
AND

PRIMARY
SUN
GEAR SHAFT

(FMX TRANSMISSION)

1.
Inspect
the
thrust surfaces
and

journals
for
scores. Inspect
the
inter-

nal gear
for
broken
or
worn teeth.

2.
Inspect
the
aluminum sleeve
for

scores
or
leakage. Inspect
the
ring

grooves
for
burrs.

3.
Inspect
the
keyway
and
drive

ball pocket
for
wear,
and
inspect
the

splines
for
burrs, twist
or
wear.

4.
Inspect
the
output shaft sleeve

for alignment with
the
governor drive

ball (Fig.
24).

5.
Inspect
the
external parking gear

teeth
for
damage
and the
speedometer

drive gear teeth
for
burrs.

6.
If
either
the
output shaft
or
ring

gear
has
been replaced, place
the as-

sembled unit with
the
gear face down

on
the
bench, push
the
shaft down-

ward,
and
check
the
clearance
be-

tween
the top of the
snap ring
and its

groove
(Fig. 25).
If
this clearance
ex-

ceeds 0.002 inch, replace
the
snap ring

with
a
thicker ring
to
reduce
the
clear-

ance
to
less than 0.002 inch. Selectiveprocarmanuals.com

07-01-16
General Transmission bervice
07-01-16

CENTER SUPPORT

PLANETARY CLUTCH
"CAM TYPE" CLUTCH RACE

CHAMFER ON PRODUCTION

PART, ONLY-SERVICE PART NOT CHAMFERED
PLANET CARRIER

D1938-A

FIG. 27—Roller Type Planetary Clutch, Carrier and Center Support

shows wear or deterioration, replace

the seal.

4.
Inspect the seal counterbore and

remove all burrs and scores with cro-

cus cloth.

REAR CLUTCH (FMX)

AND REVERSE-HIGH CLUTCH

(C4 AND C6 AUTOMATIC)

1.
Inspect the drum band surface,

the bushing, and thrust surfaces for

scores. Minor scores may be removed

with crocus cloth. Badly scored parts

must be replaced.

Inspect the clutch piston bore and

the piston inner and outer bearing sur-

faces for scores. Check the air bleed

ball valve in the clutch piston for free

movement. Check the orifice to make

sure it is not plugged.

2.
Check the fluid passages for ob-

structions. All fluid passages must be

clean and free of obstructions.

3.
Inspect the clutch plates for wear

and scoring and check the plates for

fit on the clutch hub serrations. Re-

place all plates that are badly scored,

worn or do not fit freely in the hub

serrations.

4.
Inspect the clutch pressure plate

for scores on the clutch plate bearing

surface. Check the clutch release

spring(s) for distortion.

5.
On an FMX transmission, in-

spect the needle bearing for worn rol-

lers.

FRONT CLUTCH (FMX)

AND FORWARD CLUTCH

(C4 OR C6

TRANSMISSIONS)

1.
Inspect the clutch cylinder thrust

surfaces, piston bore, and clutch plate
serrations for scores or burrs. Minor

scores or burrs may be removed with

crocus cloth. Replace the clutch cylin-

der if it is badly scored or damaged.

2.
Check the fluid passage in the

clutch cylinder for obstructions. Clean

out all fluid passages. Inspect the

clutch piston for scores and replace if

necessary. Inspect the piston check

ball for freedom of movement and

proper seating (Fig. 28).

CLUTCH

CYLINDER

PISTON

SEAL
CLIP

D1939-A

. 28—Clutch Piston Check

Valve

3.
Check the clutch release spring

for distortion and cracks. Replace the

spring if it is distorted or cracked.
4.
Inspect the composition and the

steel clutch plates and the clutch pres-

sure plate for worn or scored bearing

surfaces. Replace all parts that are

deeply scored.

5.
On FMX and C4 transmissions,

check the clutch plates for flatness

and fit on the clutch hub serrations.

Discard any plate that does not slide

freely on the serrations or that is not

flat.

6. Check the clutch hub thrust sur-

faces for scores and the clutch hub

splines for wear.

7.
On an FMX transmission, in-

spect the turbine shaft bearing sur-

faces for scores. If excessive clearance

or scores are found, discard the unit.

Check the splines on the turbine

shaft for wear and replace the shaft if

the splines are excessively worn. In-

spect the bushing in the turbine shaft

for scores. On a C4 or C6 Automatic

transmission, check the input shaft for

damaged or worn splines.

FRONT PUMP AND

STATOR SUPPORT

1.
Inspect the mating surfaces of

the pump body and cover for burrs.

2.
Inspect the drive and driven gear

bearing surface for scores, and check

the gear teeth for burrs. Inspect the

stator support splines for burrs and

wear.

3.
Check the fluid passages for ob-

structions.

4.
If any parts other than the stator

support are found defective, replace

the pump as a unit. Minor burrs and

scores may be removed with crocus

cloth. The stator support is serviced

separately.

5.
On a C4 or C6 Automatic trans-

mission, check the oil ring grooves in

the stator support for nicks, burrs or

damaged edges. On a C6 transmis-

sion, check the large seal ring groove

of the pump body for damage. Check

the gasket mating surface of the pump

body for damage.

REAR SUPPORT

(FMX TRANSMISSION)

1.
Inspect the gasket mating sur-

faces for damage.

2.
Inspect the support bushing for

scores.

3.
Inspect the rear support fluid

passages for obstructions.

4.
Check the fit of the fluid tubes in

the support.procarmanuals.com