1953 JEEP DJ torque

CLUTCH

FIG.
1-14—LIFTING
LEVER
AND
EYEBOLT FROM PRESSURE PLATE
1—
Lever

2—
Eyebolt

3—
Fulcrum
A Pressure Plate
lever and the upper end of the
eyebolt
are as
near
together
as possible. Keep the
eyebolt
pin seated in its socket in the lever as shown in Fig.
1-13.
Lift
the fulcrum over the ridge on the end of the lever.
Lift
the lever and
eyebolt
off the
pressure plate as shown in Fig. 1-14.
1-19.
Inspect
Pressure Plate and Disc
Inspect the pressure plate to make sure that it is not cracked or scored.
Check
on a surface plate
for a warped condition, as a pressure plate out of alignment
will
result in clutch chatter.
Machin­

ing or grinding the face of a warped pressure
plate is not recommended. If a warped condition
exists, replace the pressure plate. A new plate
should be installed if the plate or cushion springs appear to be defective. The cushion springs must
not be bent out of shape or flattened.

The
clutch discs for the nine or twelve spring clutches are designed for operation with their
respective clutches. Difference in general appear­ ance of the discs may be noted in the method of
housing the six torque dampening springs and in the
hub design.

After
removal of the clutch assembly, the disc should be inspected. The presence of grease or oil
on the friction facing can cause the clutch to chatter

and
grab during
engagement
and slip at higher speeds. If this condition is evident, the facings or
disc should be replaced and the cause of oil ac­
cumulation corrected. Excessively worn facings
should be replaced. The clutch disc must be in­ stalled with the long end of the hub toward the

transmission.
1-20.
Inspect Transmission Clutch
Shaft

Slide
the clutch driven plate
onto
the transmission

clutch
shaft to make sure that it is free on the
splines. If the splines on the transmission clutch
shaft are
burred,
remove the
burrs
with a fine file or
stone.
If the movement of the clutch driven
plate is not free on the splines, the result
will
be
clutch
drag and
hard
shifting of transmission gears.
1-21.
CLUTCH
PRESSURE
PLATE ASSEMBLY AND
ADJUSTMENT

1-22. Assemble
Clutch
Levers

Prior
to assembly, apply a small amount of petro­

latum
to each slide of the pressure plate lug.

a.
Lay the pressure plate on the block in the
press.
b. Assemble a lever,
eyebolt,
and pin holding the
lever and
eyebolt
as
close
together
as possible.

With
the other hand, grasp the fulcrum as shown
in
Fig. 1-15.

c.
Insert the fulcrum in the
slots
of the pressure
plate lug.
Lower
slightly and tilt the lower
edge

until
it touches the vertical milled surface of the
lug.
Insert the lower end of the
eyebolt
in the

hole
in the pressure plate. The short end of the lever
will
then be under the hook of the lug and

near
the fulcrum.

d.
Slide the fulcrum upward in the
slots
of the

lug.
Lift
it over the ridge on the short end of the
lever and drop it into the
groove
in the lever
(Fig.
1-15).
1-23.
Assemble
Clutch
Spring and
Cover

a.
After all levers are installed, place the felt grease pads over the eyebolts.
Lubricate
pads

sparingly
with light
engine
oil.
Then
place the
clutch
pressure springs in a vertical position on
the spring
bosses.
FIG.
1-15—INSTALLING
CLUTCH LEVERS

1—
Lover

2—
Eyebolt

3—
Fulcrum

4—
Pressure
Plate
232

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

I thickness: .285"
[0,724
cm.], .305"
[0,775
cm.].

Each
spacer should be hardened and ground to size, and then have the dimensional thickness
stamped thereon.

c.
From
flat bar stock at least Vfe" [3 mm.] thick,
make a
gauge
as shown in Fig. 1-22. Harden, grind
to size, and stamp sizes on the
gauge.

1-27.
Clutch Installation

a.
Very
sparingly, apply wheel bearing lubricant
to inner surface of pilot bushing in crankshaft.

Caution:
If
excessive
lubricant is applied to pilot bushing, it
will
run out on face of flywheel when
hot and
ruin
the driven plate facings.
b. Make sure that splines in the driven plate hub
are
clean; apply a light coat of lubricant to splines
of hub and transmission drive gear shaft. Slide plate over gear shaft several times; remove plate
from shaft and wipe off
excess
lubricant.

Caution:
Driven plate facings must be kept clean

and
dry.

c.
Fill
groove
in throwout bearing collar with wheel bearing lubricant. See Fig. 1-23. Make sure
that front bearing retainer of transmission is clean;
apply a light coat of wheel bearing lubricant. Slide
throwout bearing over bearing retainer several times. Remove bearing from retainer and wipe off

excess
lubricant.

12736
FIG.
1-23—LUBRICATION
POINTS
—

CLUTCH
THROWOUT
BEARING
COLLAR

1—Coat
This
Groove 2—Pack
This
Recess
d.
Clean
and apply wheel bearing lubricant to ball
stud in flywheel housing and to the
seat
in clutch

fork.

e.
If disassembled, install pressure plate in the cover assembly, lining up the
groove
on its
edge

with the
groove
on the
edge
of the cover.
Install

pressure plate retracting springs, and the three
drive
strap-to-pressure plate
bolts
and lock washers.

Torque
bolts
11 lb-ft. [1,51 kg-m.].

Note:
The diaphragm
type
clutch assembly is fac­
tory calibrated and requires no adjustment
before
installation. Refer to Par. 1-14 to adjust Borg and

Beck
coil spring
type
clutch assembly.
f.
Install
the pressure plate and driven plate on
flywheel. Support both assemblies with a spare
main
drive gear.

Note:
Be certain that
mark
on clutch cover is
aligned with the
mark
made on the flywheel during
clutch removal.
g.
Install
clutch attaching
bolts
and tighten alter­ nately so that clutch is drawn squarely
into
position
on flywheel.
Each
bolt
must be
tightened
one turn at a time to avoid bending the clutch cover flange.

Torque
bolts
30 to 40 lb-ft. [4,1 a 5,5 kg-m.].

h.
Lubricate
the ball stud and clutch fork with
wheel bearing lubricant and install clutch fork.

Note:
Be certain that fork retaining spring is
tight

on pivot ball stud.

i.
Install
flywheel housing on
engine
cylinder
block.

Caution:
Be certain that dowel pins are installed

in
cylinder block.

j.
Lubricate
the recess on the inside of the throw-
out bearing collar. Be careful not to use too much
lubricant.
See Fig. 1-23.

Caution:
Make certain that the lips of the spring
retainer (attached to the clutch fork) are in
groove
of the bearing. See Fig. 1-24.
k.
Install
throwout bearing assembly and connect
clutch linkage.
I.
Install
transmission as described in Section J. m. Adjust clutch for %"
[19,05
mm.] free travel,
see
Par.
1-3. 235

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

I
1-28.
SERVICE
DIAGNOSIS

SYMPTOMS
PROBABLE
REMEDY

Slipping:
Improper Pedal Adjustment Adjust Pedal Free
Travel

Weak Pressure Springs Replace
Lining
Oil Soaked Install New Driven Plate
Worn
Linings or
Torn
Loose from Plate Install New Driven Plate
Burned Clutch Replace

Grabbing
or
Chattering:
Gummy or Worn Linings Install New Driven Plate
Loose Engine
Mountings
Tighten Scored or Broken Pressure Plate Install New Pressure Plate
Improper Clutch Finger Adjustment............ Readjust

Clutch
Plate Crimp or Cushion Flattened Out.... Replace Driven Plate
Dragging: Too Much Pedal Play. Adjust Improper Finger Adjustment. Readjust
Pressure Plate Binds in Bracket Adjust
Warped Pressure or Driven Plate Replace
Torn
or Loose Clutch Facing. Replace

Rattling:
Broken or Weak Return Springs in Driven Plate.. Replace

Worn
Throwout Bearing Replace
Fingers Improperly Adjusted Readjust

Worn
Driven Plate Hub of Transmission Main Gear Shaft.............. Replace
Pilot Bushings in Flywheel Worn.
.............
Replace
Pilot Bushing in Crankshaft Worn Replace
1-29.
CLUTCH
SPECIFICATIONS

ENGINE
HURRICANE
F4
DAUNTLESS
V-6

DAUNTLESS
V-6

EARLY
MODELS
LATE
MODELS

Pressure Plate;
Auburn
G.M.

Borg and Beck
Type
Single
Dry Plate
Single
Plate, Dry Disc.

Single
Plate, Dry Disc.
No. of Springs 3 Diaphragm Type

Coil
Spring Type (9)

Total
Plate Pressure 1150 lb.
[521,6
kg.]
1600 lb. [725 kg.] 1765 lb. [800 kg.]
Driven Plate Make
Auburn
or Borg & Beck
G.M.

Borg and Beck
Facings Woven
Asbestos
Woven
Asbestos

Woven
Asbestos

Diameter 9.25" [23,4 cm.] 10.4" [26,4 cm.]
10.4" [26,4 cm.]
Thickness .125" [3,17 mm.] .135" [3,38 mm.]
.135" [3,38 mm.]
Torque Capacity 216 lb-ft.
[29,87
kg-m.]
246 lb-ft.
[34.01
kg-m.]

250 lb-ft.
[34,57
kg-m]

Clutch
Release Bearing: Sealed
Ball
Bearing

.
Type Sealed
Ball
Bearing Sealed
Ball
Bearing Sealed
Ball
Bearing

.
Type
Prelubricated Prelubricated
Prelubricated

Clutch
Pilot Bushing:
In
Crankshaft

In
Flywheel
In
Crankshaft
In
Crankshaft

Material
Bronze Bronze
Bronze
Size.
I.D.
.628" [15,9 mm.]
I.D.
.592"
[18,05
mm.]

I.D.
.592"
[18,05
mm.]

Clutch
Pedal Adjustment. .. W
[19,05
mm.]
%n
[19,05
mm.]

%n
[19,05
mm.]
1-30.
CLUTCH
ADJUSTING
FIXTURE
DATA

Manufacturer Disc Diameter Spacer Thickness Gauge Length

Auburn
9j£"
[23,4 cm.]
10.4" [26,4 cm.] .285"
.305"

0,723
cm.]

0,774
cm.]
mtf
[4,9 cm.]
2.0" [5,08 cm.]

9j£"
[23,4 cm.]
10.4" [26,4 cm.] .285"
.305"

0,723
cm.]

0,774
cm.]
mtf
[4,9 cm.]
2.0" [5,08 cm.]

THREE-SPEED
TRANSMISSION

ing
snap
ring.
Care should be taken to
install
the
proper
snap
ring
at
these
locations.

fl.
Install
the mainshaft rear bearing
adapter,

spacer,
transfer
case
drive
gear,
flat
washer, and

nut.
Torque nut 130 to 170
lb-ft.
[17,9 a 23,5
kg-m.].
Refer to Fig. J-15.
o. Check the main drive bearing retainer oil seal.
If
seal is
worn
or damaged it must be replaced.
Refer to Fig. J-33. 12858

FIG.
J-34—INSTALLING
MAIN
DRIVE GEAR BEARING RETAINER

-Gasket

-Bearing
Retainer
p.
Install
main drive
gear
bearing retainer gasket,
and retainer assembly. Make certain the oil drain

hole
slot in the retainer housing and gasket are

aligned.
Install
the three
ferry
type screws and
washers. Refer to Fig. J-34.
q.
Install
the transmission
case
cover gasket,
p.
Position the transmission
gear
train
and
shift

cover housing assembly in neutral. Enter the

shifter
forks
into
the
clutch
sleeves
and
align
cover,

case
and gasket holes.
Install
capscrews and
lock­

washers
and torque 8 to 15
lb-ft.
[1,1 a 2,1
kg-m.].
Refer to Figs. J-35 and J-36.

S.
This completes the transmission reassembly. 12857

FIG.
J-35—MAINSHAFT
GEAR TRAIN
—
NEUTRAL
1— Reverse Gear

2— Low
Synchronizer Assembly

3— Low
Gear
4— Second Gear
5—
Second-Third
Synchronizer Assembly
6—
Main
Drive
Gear

FIG.
J-36—INSTALLING CANE SHIFT
COVER
ASSEMBLY
1—
Control
Housing'
Cover•''

2—
Gasket
3—
Second-Third
Shift
Fork
4— Low-Reverse
Shift
Fork 256

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

ft
TRANSFER CASE

Contents

SUBJECT
PAR.

GENERAL
. . .K-1

TRANSFER CASE REMOVAL
K-2
TRANSFER CASE DISASSEMBLY
K-3
Front
Bearing Cap K-4

Rear
Bearing Cap K-5

TRANSFER CASE REASSEMBLY.
. .K-6

TRANSFER CASE INSTALLATION
K-7
TRANSFER CASE LINKAGE
ADJUSTMENT
K-8

SERVICE
DIAGNOSIS
K-9

SPECIFICATIONS
.K-10

K-1. GENERAL
All
4-wheel-drive models are equipped with a
transfer
case to connect the power to the front
axle.
It is essentially a
two-speed
transmission
located at the
rear
of the standard transmission
and
provides a low and direct gear.

The
transfer case gears are controlled by the
driver

through
one shift lever.
Early
'Jeep'
Universal
Models with the F4-134
Hurricane
engine
are equipped with two transfer case shift control levers.

a.
On vehicles equipped with one transfer case

shift
lever, the transfer case shift lever has four
positions: 2WD
High,
4WD
High,
Neutral, and
4WD
low. The forward position of the lever 2WD

High
allows the
rear
wheels only to drive. The

first
rear
position (4WD High)
engages
the 4- wheel drive and provides high range 4-wheel drive.

The
second
rear
position (Neutral)
disengages
all power to the wheels and is used for stationary
power take-off operations. The last
rear
position
(4WD
Low) provides low range 4-wheel drive.

b.
On vehicles equipped with two transfer case

shift
levers, the transfer case front axle drive lever (left hand lever)
gives
a choice of 2-wheel or 4-
wheel drive. In the forward (out) position the
vehicle is in 2-wheel drive. Move the lever to the

rear
(in) position for 4-wheel drive operation.
The
4-wheel-drive
auxiliary-range
shift lever (right

hand
lever) has three positions; low, neutral, and
high.
The forward position (low)
gives
low-range
4-wheel drive. The center position (neutral) dis­
engages
all power to the wheels and is used for

stationary
power take-off operations. A built-in in­

terlock
prevents shifting into low range, 2-wheel
drive.
This
feature protects the
rear
axle from over­

load.
K-2.
Removal of
Transfer
Case

The
transfer case may be removed from the vehicle
without removing the transmission. Where both

transmission
and transfer case are to be removed
together,
refer to Section J. To remove only the

transfer
case from the vehicle, proceed as follows:

a.
Drain
transmission
and transfer case and replace

drain
plugs.

b.
Disconnect the brake cable.

c.
Disconnect front and
rear
propeller shafts at
the transfer case. See "Propeller Shafts and
Uni­
versal
Joints."

d.
Disconnect
speedometer
cable at transfer case. e. Disconnect the transfer case shift levers. On
vehicles equipped with two shift levers
loosen

set screw and remove pivot pin. Use a screw
driver

to pry shift lever springs away from shift levers.
Lift
levers from transfer case. On models equipped

with
a single shift lever remove pivot pin cotter

key,
and the adjusting rod attaching nut to remove

shift
lever. See Fig. K-4.
f. Remove cover plate on
rear
face of transfer case.

Remove
cotter key, nut and washer from trans­

mission
main shaft.
g. If possible, at this point remove the transfer case main drive gear from the transmission main

shaft.
If not possible, see
step
j below.

h.
Remove transfer case torque reaction support

bracket
bolt and nut.

i.
Remove transmission to transfer case bolts.
j.
Remove transfer case. If the transfer case main

drive
gear has not been removed in
step
g above,
proceed as follows:
Brace
the end of the trans­

mission
main shaft so that it cannot
move
in the
transmission,
pull
the transfer case to the
rear
to 267

L

PROPELLER
SHAFTS
AND
UNIVERSAL JOINTS

move
the snap rings, pinch the ends
together
with

a
pair
of pliers. If the rings do not readily snap
out of the groove, tap the end of the bearing lightly
which
will
relieve pressure against the rings.
After
removing the snap rings, press on the end of
one bearing until the
opposite
bearing is pushed
from
the yoke arm.
Turn
the joint over and press
the first bearing back out of that arm by pressing
on the
exposed
end of the
journal
shaft. Use a
soft
ground drift with a flat face about [0,8 mm.]

smaller
in diameter than the
hole
in the yoke arm
and
drive it out, otherwise there is danger of damag­ing the bearing.

Repeat
this operation for the other two bearings,
then lift out
journal
assembly by sliding it to one
side.

L-4.
Snap
Ring
Type Assembly

Wash
all parts in cleaning solvent and inspect the
parte
after cleaning. Replace any parts that indicate
extensive
wear.
It is advisable to install new gaskets
on the
journal
assembly regardless of the condition of the old gaskets. Make certain that the grease

channel
in each
journal
trunnion is open.

Pack
the bearing
cones
one-third
full
of lubricant
and
install the rollers.
Draw
the bearings into the end yoke arm and seat
them firmly against the bearing shoulders. Hold
the bearings in a vertical position to prevent the
needles
from dropping out until the joint is as­ sembled. If the joint binds when assembled, tap
the arms lightly to relieve any pressure on the bear­
ings at the end of the
journal.

L-5.
U-Bolt
Type Disassembly

Removal
of the attaching "U"-bolt releases one set
of bearing races. Slide the propeller shaft into the
yoke flange to remove them using care not to
lose
the rollers.
After
the removal of the one set of bearing races,
release the other set by removing the snap rings

in
the
sleeve
yoke by pinching the ends
together

with
a
pair
of pliers. Should the rings
fail
to snap
readily
from the groove, tap the end of the bearing
lightly,
which
will
relieve the pressure against them.

Press
on the end of one bearing, until the
opposite
bearing
is pushed out of the yoke arm.
Turn
the

universal
joint over and press the first bearing out
by pressing on the
exposed
end of the
journal
as­
sembly. Use a
soft
ground drift with a flat face about
\{i
[0,8 mm.] smaller in diameter than the
hole
in the yoke
arm
and drive out the bearing.
Lift

the
journal
out by sliding to one side.
Clean
all
parts
and check for wear.

L-6.
U-Bolt Type Assembly

Wash
all parts in cleaning solvent and inspect the
parts
after cleaning. Replace any parts that indicate
extensive
wear.
It is advisable to install new gaskets
on the
journal
assembly regardless of the condition
of the old gaskets. Make certain that the grease
channel
in each
journal
trunnion is open.

Pack
the bearing
cones
one-third
full
of lubricant
and
install the rollers.
Draw
the bearings into the end yoke arm and seat
them firmly against the bearing shoulders. Hold the
bearings in a vertical position to prevent the
needles
from dropping out until the joint is as­
sembled. If the joint binds when assembled, tap the arms lightly to relieve any pressure on the
bearings at the end of the
journal.
Tighten the
U-bolts equally. U-bolt torque wrench reading is 15 to 20 lb-ft. [2,07 a 2,76 kg-m.].

When
installing the assembly in the vehicle be sure
that the arrows on the propeller shaft and yoke

sleeve
are in alignment as shown in Fig. L-2, or
that the unmarked joints are aligned with the yokes in the same parallel plane.

SPECIFICATIONS

L-7.
PROPELLER
SHAFTS
AND
UNIVERSAL JOINTS
PROPELLER
SHAFTS:

Make
SPICER

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
Front

Rear

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
O.D.

Length

O.D.
Length

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
1M"
[3,175 cm.]

1M*
[3,175 cm.]

\W
[3,175 cm.]
1M*
[3,175 cm.] [3,175 cm.]

\W
[3,175 cm.]

\W
[3,175 cm.] [3,175 cm.] 22^" [57,78 cm.]

28H"
[72,39 cm.]
22M*
[57,78 cm.]

mW
[72,39 cm.]

33He"
[85,57 cm.]

21W
[55,25 cm.]
21%"
[55,25 cm.]

2&* [68,10
cm.]
IK"
[4,45 cm.]

1M#
[4,45 cm.]

\%"
[4,45 cm.]

\%"
[4, 45cm.]

IW
[4,45 cm.]

1M*
[4,45 cm.]

3*
[7,62 cm.]
2" [5,08 cm.]
2" [5,08 cm.]
l%" [4,45 cm.]
182£"
[45,95 cm.]
WW
[34,131
cm.]

3SJ4*
[97,79 cm.]

33%"
[84,69 cm.] 19546*
[50,64
cm.]
24^"
[61,60
cm.]

44M*
[112,40
cm.]

19%?
[50,64
cm.] 39* [99,06 cm.]

U%"
[37,47 cm.l

UNIVERSAL
JOINTS:
Make
Spicer

Cardan
Cross
Antifriction

Type
Spicer

Cardan
Cross
Antifriction

Bearing
Spicer

Cardan
Cross
Antifriction

276

M
FRONT
AXLE
1— Nut
2—
Lock
Washer

3—
Bearing
Lock
Washer
4—
Wheel
Bearing Cup 5—
Cone
and Rollers
6—
Oil
Seal 7— Spindle
8— Spindle Bushing
9—
Filler
Plug
10—
Right
Knuckle and Arm
11— Shims
12— Pivot Pin
13—
Lock
Washer
14—
Cap
Screw
15— Nut
16—
Washer

17—
Universal
Joint Yoke
18—
Oil
Seal
19—
Oil
Slinger
FIG.
M-2—FRONT
AXLE

20—
Cone
and Rollers
21—
Bearing
Cup
22—
Right
Axle Shaft with Universal Joint
23—
Knuckle
Oil Seal Retainer
24— Housing Breather 25—
Front
Axle Housing
26—
Axle
Shaft with Universal Joint
27—
Oil
Seal
28—
Axle
Shaft Guide
29—
Shim
Pack
30—
Bearing
Cup
31—
Cone
and Rollers
32—
Ring
Gear
and Pinion
33—
Thrust
Washer

34—
Thrust
Washer

35—
Differential
Gears
36— Housing Cover Gasket
37— Housing Cover
38—
Fill
Plug 39—
Screw
and
Lock
Washer
40—
Bearing
Cup
41—
Cone
and Rollers
42— Shims
43—
Lock
Pin
44—
Pinion
Shaft
45—
Differential
Case
47— Bolts
48— Nut
49—
Oil
Seal and Backing Ring
50—
Thrust
Washer
51— Snap Ring
52— Stop Bolt
53— Nut 54—
Bearing
Cup
55—
Cone
and Rollers
56—
Gasket

checked, making sure it is clean and open.

The
front wheel bearings should be checked every
12,000
miles. Refer to Section Q. Front wheel toe-

in
is adjustable by lengthening or shortening the
tie rod. However, standard caster and camber of
the front
wheels
are built
into
the axle. Wheel
caster can be adjusted by placing tapered shim
plates or
wedges
between
the springs and spring

seats
welded to the axle housing. Steering
geometry

and
front wheel adjustments are discussed in Sec­ tion O.

The
axle housing should be checked periodically
for weld cracks and/or other damage that may cause misalignment of the front
wheels
or
loss

of lubricant. The spring clips (U-bolts) should be
inspected and torqued every
12,000
miles. Torque (spring clip) nuts 45 to 50 lb-ft. [6,2 a 6,9 kg-m.].

M-4. FRONT
AXLE
REMOVAL
a.
Raise front end of vehicle
arid
safely support the frame by placing stands under the frame at
the rear of the front spring rear hangers.
b. Place
jack
under front axle housing and relieve
axle
weight
from the springs.
c. Disconnect shock absorbers from spring clip plates.
FIG.
M-3—HUB
CAP
PULLER

d.
Disconnect steering link from tie rod socket-
joint assembly.
e. Disconnect hydraulic brake
hoses
from front

brake
lines. Disconnect
hoses
from frame brackets. 278

FRONT
AXLE

FIG.
M-l
1—FRONT
STEERING

KNUCKLE

(With
Spicer Universal Joint)
1—
Wheel
Hub Cap

2—
Driving
Flange Cap Screw

3—
Axle
Shaft Drive Flange Gasket 4—
Wheel
Bearing Cup
5—
Front
Wheel Spindle
6—
Brake
Drum
7—
Front
Brake
Cylinder

8—
Brake
Backing Plate

9—
Pivot
Pin Bearing Cap
10—
Pivot
Pin Bearing Cap Nut
11—
Pivot
Pin 12—
Pivot
Bearing Adjusting Shims

13—
Pivot
Pin Cone and Rollers
14—
Steering
Knuckle
Oil Seal 15—
Front
Axle Universal Joint
16—
Thrust
Washer
17—
Brake
Backing Plate Screw
18—
Brake
Shoe and
Lining

19—
Hub
Oil Seal
20—
Wheel
Hub Bolt Nut
21—
Wheel
Bearing Cone and Rollers 22—
Wheel
Bearing Washer

23—
Wheel
Bearing Retaining Nut
24—
Wheel
Adjusting Nut
Lock
Washer
25—
Wheel
Bearing Retaining Nut
26—
Snap
Ring

c.
Install
the wheel bearing spindle and bushing.
d.
Install
brake backing plate.
e.
Grease and assemble wheel bearings and oil

seal.
Install
the wheel hub and drum on the wheel
bearing
spindle.
Install
the wheel bearing washer
and
adjusting nut. Tighten nut with
Wrench
W-144
as shown in
Fig.
M-5, until there is a slight drag on the bearings when the hub is turned.
Then
back off approximately one-sixth of a
turn.
Install
lock

washer
and nut, tightening nut
into
place, and then bend lip of lock washer over on the locknut.
f.
Install
drive
flange
and gasket on hub and attach
with
six cap screws and lock washers.
Install
snap

ring
on outer end of axle shaft.

g.
Install
hub cap.
h.
Install
the wheel, lug nuts, and wheel disc.
i.
If
tube
was installed with axle assembly on
vehicle, check front wheel alignment (Section O),
bleed brakes (Section P), and lubricate front axle

universal
joints (Section B).

M-12.
FRONT
AXLE
INSTALLATION

To
install the front axle, reverse the procedures described in
Par.
M-4 and then perform the follow­
ing operations:

a.
Torque spring clip plate (U-bolt) nuts securing the axle to the front springs, (see Par. M-4).

b.
Adjust and bleed the brakes (see Section P).

c.
Check
axle lubricant level and
fill
as necessary, (see Section B).

d.
Check
front end wheel alignment (see Section
O).
e.
Check
wheel turning angle. Refer to Par. M-14.
M-13.
Steering
Tie Rod and
Bell Crank

These
parts of the front axle are covered in Sec­
tion O.
M-14.
4-Wheel Drive
Turning
Angle

Adjustment
and service information regarding
turning
angles
is covered in Section O.

M-15.
2-WHEEL-DRIVE
FRONT
AXLE
The
front axle is of the reverse
Elliot
type. It is a
steel forging, heat treated for strength and ma­
chined
to
close
limits. The steering knuckles are
mounted on pins which pass through
openings
at each end of the
"I"
beam and are locked securely

in
position with tapered pins and nuts. The knuckles

ride
on
ball
thrust bearings for
ease
of steering. See
Figs.
M-12, M-13.

The
knuckles are connected by a tie rod which is
mounted on
ball
and socket connections. The tie

rod
is adjustable to secure correct
toe-in
of the front wheels. A steering connecting rod
connects

the
left
knuckle arm with the steering gear arm.

Standard
caster and camber of the front
wheels
are
built
into
the front axle. Wheel camber cannot
be changed however, caster can be adjusted by

placing
tapered shims or
wedges
between
the
springs and spring seats. For
complete
information

regarding
the steering
geometry
refer to the
Section O.

M-16.
Removal of Solid
Front
Axle

Note:
The procedure for removing the solid front
axle varies slightly, depending on whether the
springs are slung under or over the axle. These

variations
are
noted
in the following procedure.

a. -
Raise the front end of the vehicle and safely support the frame behind the springs.

b.
Remove the
wheels
by removing the wheel
discs and lug nuts.

c.
Disconnect the steering connecting rod at the
ball
and socket connection on the steering knuckle. 282