1953 JEEP DJ horn

STEERING
SYSTEM

O-L
GENERAL

The
steering system on all Jeep Universal vehicles
consists of the steering gear, steering wheel, steering column and shaft, and steering linkage.
This

section covers wheel alignment, steering linkage,
steering gear, steering column and steering wheel.
0-2. Steering
Gear
Function

The
steering gear is a reducing gear. It exchanges a

relatively
large amount of movement with a small force (applied by the driver at the steering wheel), for a much smaller amount of movement with a
greatly increased force through a cam and lever
action type steering gear. The steering gear ratio is 17.9 to 1 on vehicles equipped with the F4
engine

and
19 to 1 with the V6 engine.
0-3. Steering
Linkage
Refer
to Fig. O-l.
The
steering linkage consists of a steering arm at­
tached to the steering gear, a steering connecting

rod,
(drag
link),
connecting the steering arm to the
beilcrank,
and a steering tie rod connecting the
beilcrank
to the axle tie rod. The beilcrank pivots
on a pin mounted just to the left of the frame front crossmember. The steering tie rod is connected to
the beilcrank and
extends
to the right
ball
joint as­ sembly of tie rod. The tie rod
extends
to the wheels,
being connected to their respective steering knuckle

arms
at the wheels.
With
this linkage arrangement,
as the steering arm
moves
rearward,
the front
wheels
turn
to the left. As the steering arm
moves
forward,
the wheels
turn
to the right.
Ball
joints are used to secure the drag
link,
steering
connecting rod and tie rod ends. The
ball
joints
assist in maintaining
good
steering control and con­
stant toe-in of the front wheels under all driving conditions. If the
ball
joints
become
worn enough
to allow free motion in the linkage, they should be,

replaced.

Note:
Ball
joint replacement of the tie rod requires
resetting of the wheel toe-in adjustment.
0-4.
Steering
Column
and Gear
Alignment
When
adjusting a steering gear remove all loads
from
the unit by disconnecting the steering con­
necting rod (drag
link)
from the steering arm and
also
loosen
the instrument panel bracket and the
steering gear to frame
bolts
to allow the steering
post
to correctly align itself. When retightening the
steering gear to frame
bolts
use a torque wrench
pull
of 45 to 55 lb-ft. [6,2 a 7,6 kg-m.] on the

Vk*
bolts
and 30 to 40 lb-ft. [4,15 a 5,5 kg-m.] on the
Vs"
bolts. 10811

FIG.
0-2—STEERING
GEAR
1—Nut

2
—Lockwasher

3—
Steering
Gear
Arm 4—
Lever
Shaft Oil Seal
5—
Outer
Housing Bushing
6—
Inner
Housing Bushing 7—
Filler
Plug
8—
Cover
and Tube
9—
Ball
Retaining
Ring

10—Cup
11—
Ball
(Steel)
12—
Tube
and Cam
13—
Shims

14—
Upper
Cover

15—
Lockwasher

16—
Bolt

17—
Steering
Wheel 18—
Horn
Button Retainer
19—
Horn
Button
20—
Horn
Button Cap 21— Nut
22—
Spring
23—
Spring
Seat
24—
Bearing
25—
Horn
Cable

26—
Horn
Button Spring
27—
Spring
Cup
28—
Steering Column
29—
Oil
Hole
Cover

30—
Clamp
31—
Adjusting
Screw
32— Nut
33—
Bolt

34—
Side
Cover
35—
Gasket

36—
Shaft
and
Lever

37—
Housing
314

STEERING
SYSTEM

FIG.
0-9—STEERING

BELLCRANK
ASSEMBLY

1— 5s'-18
Stollock
Lockout

2—
Plain
Washer

3— 7 us"-20
x
2 l2' Bolt

4—
71«
*-20
Stollock
Locknut
5—
Beilcrank
Support

6—
Special
Ground
Washer
7— Seal
8—
Bearing
9— Beilcrank
10— Beilcrank
Shaft

11—
Seals

12—
Bearings

13— } s *
b.
Torque the
Vfc"
[11,113
mm.] diameter elamp
bolt to
50-70
lb-ft. [6,9 a 9,7 kg-m.].

c.
Assemble the tie rod to the beilcrank lever,
making
sure to tighten the nut to the proper
torque value of 38 to 45 lb-ft. [5,2 a 6,2 kg-m.].

d.
Connect the drag
link
to the beilcrank arm,

adjust
the
ball
joint by screwing in the plug firmly against the
ball,
approximately 20 lb-ft. [2,8 kg-m.], then back off one quarter
turn
and lock

with
a new cotter pin.

0-19.
Beilcrank
Support
Bracket
Rivet
Replacement

The
procedure for replacing a rivet with a bolt
is as follows:

a.
Drill
a [4,76 mm.] pilot
hole
up through
the front rivet.

b.
Enlarge
the [4,76 mm.]
hole
with a %"
[8,73 mm.]
drill.

c.
Chisel
off the
bottom
rivet head and drive the

remainder
of the rivet upward and out, using
a
punch and hammer.

d.
Install
a %" [9,53 mm.] bolt and lock nut,
torque to
30-45
lb-ft. [4,1 a 6,2 kg-m] and stake
the nut.

e.
Clamp
a metal plate to the frame to protect
the radiator, then
drill
and remove the remaining two rivets, install bolts, lock nuts and torque as
specified.

O-20.
STEERING
COLUMN
AND
WHEEL SERVICE

Jeep
Universal
Series vehicles use a
one-piece
steer­
ing
shaft that is integral with the steering gear
assembly, as shown in Fig. 0-2. Alignment in­
structions in paragraph 0-4 apply.

0-21.
Steering
Wheel Removal •
Refer to Fig. 0-2.

a.
Carefully
pry the rubber horn cap from the housing slot.
b.
Remove steering shaft nut.

c.
Remove steering wheel and spring.

0-22.
STEERING GEAR SERVICE

Note:
The steering gear can be adjusted when the
gear is mounted in the vehicle by first disconnecting
the drag
link
from the steering arm. Refer to Par.
Q-5.
0-23.
Removal
of
Steering Gear
•
F4-Engine.

a.
Remove the directional signal unit from the steering column.

b.
Remove the steering column bracket attached
at the instrument panel.

c.
Remove upper section of the floor pan.

d.
Disconnect shift rods from the shift levers at
lower end of the steering column if applicable.

e.
Disconnect the horn wire at lower end of steer­
ing
gear assembly.

f.
Remove steering gear arm from the steering gear assembly.

g.
Remove
bolts
attaching the steering gear hous­
ing
to the frame.

h.
Remove the steering gear assembly by bringing

it
up through the floor pan opening.

•
V6 Engine.

a.
Remove oil pan
skid
plate.

b.
Remove
left
exhaust pipe.

c.
Disconnect connecting rod (drag
link)
from
steering gear arm.

d.
Disconnect steering gear assembly from frame.

e.
Remove steering wheel from steering column.
f. Disconnect accelerator linkage.
g.
Remove upper floor pan assembly.
h.
Disconnect directional signal switch.
i.
Jack-up
vehicle, and remove steering gear and
320

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

O
column assembly down through the floor pan open­
ing and out from under vehicle.
0-24.
Disassembly
of
Steering
Gear
Refer
to Fig. 0-2.

When
the steering gear arm is installed on early
production vehicles, the line across the face of the

arm
and the end of the shaft should be in align­ ment. On later production vehicles, blind splines
on the lever shaft and in the steering gear arm en­

sure
correct positioning of the arm.

a.
Remove the steering gear arm with a puller
C-3646.

Caution:
Do not use a hammer or
wedge
to re­
move
the steering arm from the shaft and lever.

This
can cause damage to the shaft assembly.

b.
Loosen the lock nut and unscrew the adjusting

screw
two turns.

c.
Remove the side cover screws and washers. Re­
move
the side cover and gasket.

d.
Remove lever shaft.

e.
Remove upper cover plate screws. Remove cam,
wheel tube, and bearing assembly from the housing.
f.
Clean
all parts with suitable cleaning solvent and wipe dry.

g.
After dismantling as outlined above is com­
pleted, inspect cam
grooves
for wear, chipping and
scoring,
also the
ball
races on the cam ends and the
separate
ball
cups. Existence of any of
these
condi­ tions indicates the necessity for parts replacement.

h.
Inspect the tapered stud mounted on the lever
shaft for flat
spots
and chipping. In the case of
either, replacement is usually advisable. Inspect the
lever shaft for wear and
test
the fit of the shaft in
the bushings.

i.
Inspect condition of the oil seal at outer end of
lever shaft and the bearing at top end of steering
column.

0-25.
Reassembly
of
Steering
Gear
e Refer to Fig. 0-2.
Reassemble all parts to wheel tube in reverse order
of dismantling. Assemble cam, wheel tube and
bearing
assembly in housing, seating the lower

bearing
ball
cup in the housing.
Note:
New plastic retainer type cam bearings are
now available for the Ross steering gears. The new
bearings replace, and are interchangeable with,
the lock ring type cam bearings on gears equipped

with
early type cams.
With
adjusting shims in place, assemble upper
cover and adjust the cam bearings.
Assemble lever shaft in housing and with gasket
in
place assemble the side cover and set adjusting

screw
for a minimum backlash of the studs in the
cam
groove, with the steering gear at the center
point of travel.
When
assembling upper bearing spring and spring
seat in jacket tube make sure that the spring seat
is positioned correctly. It must be installed with
the lengthwise flange down against the bearing and
not up inside of spring coil.

0-26.
Installation
of
Steering
Gear

a.
After the gear has been properly adjusted, as
outlined in Par. 0-5, install steering gear assembly
in
chassis in the reverse order in which it was re­
moved.

b.
After installing the assembly in the vehicle,

jack
up front of vehicle and place the front wheels
in
the straight ahead position.

c.
Temporarily install the steering wheel to locate
the mid-position of the steering gear. To locate the mid-position,
turn
the steering wheel as far to the

right
as possible and then
turn
in the
opposite
di­

rection
as far as possible, noting the total number
of turns.
Turn
the wheel back just ^ of the total movement to place the gear in mid-position.

d.
With
the steering gear in mid-position and the
wheels in the straight ahead position install steer­ ing gear arm on lever shaft with the
ball
end down.

When
installed the line across the face of the arm

and
end of shaft should be in alignment.

0-27.
Steering
Wheel
Installation
•
Refer to Fig. 0-2.

a.
Install
steering wheel and spring on shaft.

Align
scribe marks on shaft and hub of wheel.
b.
Install
steering shaft nut and torque 20 to 25
lb-ft. [2,8 a 3,4 kg-m.].

c.
Install
horn cap. Test horn.
321

T
BODY
from the windshield wiper vacuum fitting. On
late

models
disconnect electrical wires from wiper
motor. Unlatch the two windshield clamps on each

side
of the windshield.
Fold
the windshield forward

until
the
slot
in the windshield
hinges
aligns with the flat
side
of the pin in the
body
hinges.
Slip wind­
shield off the pins and remove from
body.

T-4.
Windshield Glass
The
windshield
glass
is mounted in a rubber
weatherstrip which in turn
mounts
in the frame. A
rubber
locking strip, which
holds
the
glass
firmly in
the frame, is inserted in a moulded
groove
around
the rear
face
of the weatherstrip as shown in Fig.
T-2.
To remove the
glass
it is necessary to first
remove the locking strip which may be pried out
with a screwdriver or similar
tool.
Installation is,

obvious.

T-5.
Canvas Tops

Canvas
tops
are available in
Half
Tops and
Full
Tops.
Installation instructions are provided with
each canvas top kit for each model vehicle.
FIG.
T-5—VEHICLE CONTROLS — MODEL CJ-5A, CJ-6A

SINGLE
LEVER
TRANSFER CASE 1—
Hand
Throttle 9—Transfer Case Shift
Lever

2—
Choke
Control 10—Headlight Dimmer Switch
3— Instrument Cluster 11—Clutch Pedal 4—
Light
Switch 12—Heater Controls 5— Ignition — Starter Switch 13—Hand
Brake
Handle
6— Glove Compartment 14—Transmission Shift
Lever
7—
Brake
Pedal 15—Directional Signal Switch
8— Accelerator Pedal 16—Horn Button
FIG.
T-6—TAIL GATE ASSEMBLY —
EARLY
MODEL CJ-5A, CJ-6A
354

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

T
FIG.
T-7—TAIL
GATE
ASSEMBLY

—
LATE
MODEL
CJ-5, CJ-6
T-6.
Care
of
Fabric
Tops
Remove fabric
tops
from their protective covering
immediately after they are received. Store in a

dry,
clean,
airy
place. If the material is damp, the
top should be installed on the vehicle immediately

and
washed with a mild soap; then
give
the top a

quick
and thorough rinsing.
T-7.
Brake
and
Clutch Pedal Pads

A
clutch and brake pedal pad cover has been re­ leased which has a .44" [11,18 mm.]
groove
molded into the back side of the pad cover. When installing,
the grooved opening is located down and to the

bottom
of the pedal. See Fig. T-ll. The purpose of the
groove
concerns models not listed in this
manual.
The pedal pad cover formerly used is
FIG.
T-8—VEHICLE
CONTROLS
—
LATE

CJ-5
AND CJ-6
SINGLE
LEVER
TRANSFER
CASE
1—
Light
Switch

2—
Windshield
Wiper
Switch

3—
Hazard
Warning
Light
Switch
4—
Hand
Throttle*

5—
Choke
Control

6—
Brake
Warning
Light*

7—
Windshield
Washer
Control

8—
Ignition
Starter
Switch

9—
Cigarette
Lighter*

10—
Turn
Signal
Lever

11—
Instrument
Cluster

12—
Horn
Button

13—
Glove
Compartment

14—
Transfer
Case
Shift
Lever

15—
Transmission
Shift
Lever

16—
^Heater
Controls*

17—
Accelerator
Pedal

18—
Brake
Pedal

19—
Clutch
Pedal

20—
Hand
Brake
Control

21—
Headlight
Dimmer
Switch

*On
applicable models only. solid in construction without groove.
Either

grooved and solid pad covers can be installed on

CJ-3B,
CJ-5,
CJ-5A,
CJ-6,
CJ-6A,
DJ-5 and DJ-6 models.
T-8.
Front Seat Adjustment
The
Bostrom bucket type driver's seat installed on

early
Models CJ-5, CJ-6, DJ-5 and DJ-6, are equipped with a 3-position manual adjustment.
Three
attaching
holes
are provided in the seat
support at the four seat mounting locations. To
adjust
the seat, remove the four attaching bolts,

move
the seat and four mounting spacers to the
desired
location, and reinstall the
bolts
at the new
location. Refer to Fig. T-12.

On
late models the driver's seat may be quickly ad­

justed
to the most comfortable driving position by releasing the lever located at the lower left front

edge
of the seat. Pushing the lever to the right al-
CD CD®
®@©"®^
FIG.
T-9—VEHICLE
CONTROLS
—
CJ-5,

CJ-6
DUAL
LEVER
TRANSFER
CASE

1—
Light
Switch

2—4-Way
Flasher
Switch*

3—
Hand
Throttle

4—
Choke
Control
5—
Brake
Warning
Light*

6—
Ignition-Starter
Switch

7—
Instrument
Cluster

8—
Horn
Button

9—
Qlove
Compartment

10—Heater
Controls*

•On
applicable models only.
11—
Front
Axle
Drive
Shift
Lever

12—
Transmission
Shift
Lever

13—
Aux.
Range
Shift
Lever

14—
Accelerator
Pedal
15—
Brake
Pedal
16—
Clutch
Pedal

17—
Headlight
Dimmer
Switch

18—
Hand
Brake
Control

19—
Turn
Signal
Lever
355

T

BODY
lows
the seat to be
moved forward
or
rearward.
Re­

positioning
the
lever
to the
left
will
lock
the seat
in
the
desired position.
T-9.
Passenger
Seat
Safety
Catch
Thejfront
passenger seat on
late model vehicles
is

provided
with
a
safety
catch, located
at the
left

rear
base of the seat. To
tilt
the seat
forward,
first

release
the
catch
by
pulling
upwards
on the
catch lever. 11213
.

FIG.
T-ll—CLUTCH
AND
BRAKE PEDAL
PAD

FIG.
T-10—VEHICLE CONTROLS
-
MODELS
DJ-5 AND DJ-6 1—
Light
Switch
2— Windshield Wiper Switch
3—
Hazard
Warning Light Switch
4—Hand Throttle*
5—
choke
Control
6— Windshield
Washer
Control
7— Ignition
Starter
Switch
8— Cigarette Lighter* 9—
Turn
Signal Lever
10— Instrument Cluster
11—
Horn
Button
12— Glove Compartment
13—
Heater
Controls*
14— Transmission Shift Lever
15— Accelerator
Pedal

16—
Brake
Pedal

17—
Clutch
Pedal
18—
Hand
Brake Control
19— Headlight Dimmer Switch

*On
applicable
models
only.
FIG.
T-12—EARLY MODELS
FRONT SEAT
ADJUSTMENT

1—
Location Holes
2— Spacer

S5§

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

ALPHABETICAL INDEX

SUBJECT PAR.
SUBJECT
PAR.

Abbreviations,
List
U-17 Accelerator Linkage E-70
Air
Cleaner B-25, B-26, B-82, C-21, E-69

Air
Delivery Manifold Fl-4, F2-12
Air
Filter, Pump • F2-3, F2-11

Air
Injection Tubes Fl-5, F2-13
Air
Pump Fl-2, F2-10
Alternator Bearings B-76, H-80
Alternator Brushes H-74, H-75
Alternator Charging System •
•
H-63
Alternator
Diodes
H-69, H-85
Alternator Precautions H-64 Alternator Rotor H-76, H-79
Alternator Tests H-67, H-77 Alternator Specifications H-l 52
Alternator Stator H-84
Anti-Backfire
Valve Fl-6, F2-14
Antifreeze
Chart
• G-22 Antifreeze
Solutions
- G-16
Axle Camber O-l
Axle Caster 0-8

Back-Up
Lights H-135

Ballast
Resistor. H-32 Battery C-3, H-2 Bendix Folo-Thru Drive H-105, H-106
Bleeding Brakes P-7
Body T-l Body Lubrication. B-65 Body Name Plates ' A-7

Brake
Adjustment P-14
Brake
Drums. • .P-17

Brake
Hoses
P-8

Brake
Maintenance . P-5
Brake
Master Cylinder B-40, P-2, P-20

Brake
Service P-6
Brake
Wheel Cylinder • P-21

Camber
Adjustment 0-7
Camshaft D-6, D-51, D-52, D-53, D-81, Dl-26, Dl-33, Dl-55, Dl-80

Carburetor
E-10, E-25

Carburetor
Adjustment C-25, E-14, E-40,
Fl-13,
F2-16
Carburetor
Specifications .Fl-38, F2-34, E-79

Caster
Adjustment 0-8

Charging
System Service. .H-34, H-63

Chassis
Lubrication B-7, B-83

Chassis
Torque Specifications U-14

Clutch
1-4, MO
Clutch
Adjustment 1-3
Clutch
Linkage B-44, 1-3

Clutch
Maintenance .. 1-2
Clutch
Release Bearing B-74, 1-25

Coil
C-20, H-19, H-31 Connecting Rod Bearings D-47, D-48, D-49, Dl-49 Connecting Rod
Crank
Pins D-42
Connecting Rods... .D-20, D-50, D-95, Dl-31, Dl-45, Dl-75
Controls B-59, B-62
Cooling System B-28, G-l Cooling System Filling G-2

Core
Hole Expansion Plugs D-72

Crankcase
Ventilating System B-13, C-6, D-110

Crankshaft
D-26, D-38, D-39, Dl-38, Dl-73
Crankshaft
End Play. D-83, Dl-74

Crankshaft
Main Bearing D-43, D-44, Dl-32, Dl-40, Dl-73

Crankshaft
Oil Seal, Front Dl-21, Dl-85
Crankshaft
Oil Seal, Rear D-63, D-85, Dl-72

Cylinder
Block D-32, Dl-34

Cylinder
Bores D-35, Dl-36

Cylinder
Head D-17, D-73, D-98, Dl-24, Dl-63, Dl-82

Cylinder
Head Torque. C-5
Dash Pot Adjustment C-26, E-44
Differential B-51 thru B-53, N-9 Differential Adjustments N-16, N-18
Differential, Powr-Lok N-20
Differential,
Trac-Lok
N-24
Directional Signal Lights. . H-138
Distributor B-14, B-15, C-10, D-13, Dl-9, H-9, H-20 Distributor Check H-l7, H-28
Distributor Point Dwell C-17 Distributor Resistance Test C-16

Drawbar
.R-6, U-16
Dual
Brake System P-l thru P-26

Electrical
Instruments H-l22

Electrical
Specifications .H-l52

Electrical
System H-l Engine .
..D-l,
Dl-1
Engine Code Number A-6
Engine Compression .
.
C-9 Engine Disassembly . • .D-6, Dl-5 Engine Installation D-105, Dl-102
Engine Lubrication System B-4, B-6 Engine Mountings D-3, Dl-3
Engine Oil B-9
Engine Oil Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93
Engine Oil Pan D-l9, D-66, D-97, Dl-29, Dl-51, Dl-77 Engine Oil Pump. . .D-14, D-65, D-93, Dl-19, Dl-50, Dl-87
Engine Overheating. G-l9 Engine Removal D-5, Dl-4.

Exhaust
Emission Control — F4 Fl-1 thru Fl-30
Exhaust
Emission Control — V6 F2-1 thru F2-36
Exhaust
Manifold, Install F-6

Exhaust
Pipe -
•
F-8

Exhaust
System F-2, F-3

Exhaust
System Maintenance F-4

Fan
Belt C-27, Dl-11, Dl-96, G-18
Floating Oil Intake. D-64, Dl-30, Dl-50, Dl-76 Flywheel D-25, D-67, D-87, Dl-28, Dl-52, Dl-78
Flywheel Housing. D-71, D-88, Dl-27, Dl-54, Dl-79
Flywheel Pilot Bushing D-70, 1-8

Frame
R-l

Frame
Alignment. R-2
Frame
Dimensions R-3
Frame
Straightening R-4

Front
Bumper Weight. • U-9
Front
Axle B-50, M-2

Front
Axle Alignment R-5

Front
Axle Installation • M-12
Front
Axle Maintenance M-3

Front
Axle Shaft Removal M-5

Front
Axle U-Joint B-54, B-55, M-7

Front
Axle Steering Knuckle M-&

Front
Wheel Alignment 0-4

Front
Wheel Bearings B-56, B-57, Q-4
Front
Wheel Toe-in 0-5, 0-6

Front
Wheel Turning Angle 0-9
Fuel
Gauge Float Unit F-76

Fuel
Lines - E-77

Fuel
Pump E-45, E-54, E-60, E-67
Fuel
Pump Check C-23

Fuel
Tank
E-72

G

Gauges, Testing H-l24

General
Specifications A-8
Generator B-16, H-34 thru H-40

Glass
Replacement • T-4
Governor. . .
•.
• U-3
Guides, Valve D"61

H

Hazard
Warning Lights H-139
Head Lamp Aiming H-131, H-132 Head Lamp Replacement H-130
Headlight Dimmer Switch H-l
2
7

Heat Control Valve C-7, F-7 Heated Air System • •
•
F2-2
Heater U-10
Horns.....
....H-137 371