1953 JEEP DJ brakes

BRAKES

12519

FIG.
P-13—DOUBLE
SAFETY MASTER CYLINDER
1— Boot
2— Snap Ming 3"*—Piston Assembly
4—
Backing
Ring 5—
Master
Cylinder Cup 6—
Master
Cylinder Cup
7— Piston
8—
Master
Cylinder Cup 9—
Cup
Protector
10—Spring 11—
Cylinder
Housing
12—
Cover
Gasket
13—
Cover

14—
Washer
Gasket 15—
Washer
16—
Cover
Bolt
17—
Check
Valve Spring 18—
Check
Valve
19—
Tube
Seat
20— Piston Stop
REASSEMBLY

a.
Prior
to reassembly of the master cylinder, dip

all
components
in clean brake fluid and place on
clean paper or in a clean pan.

b.
Install the primary cup washer, primary cup,
cup protector, and return spring on the secondary piston.
c. Install the piston cups in the double
groove
end
of the secondary piston, so the flat j of the cups face each other (lip of cups away from each other).
Install
the cup expander in the lip
groove
of the
end cup.

cL
Coat the cylinder bore and piston assemblies with clean brake fluid
before
installing any parts

in
the cylinder.
e. Install the secondary piston assembly first and then the primary piston which is supplied in the
repair
kit.

f.
Install the push rod assembly, which includes
the push rod,
boot,
and rod retainer, and secure
with the snap ring. Install the primary piston
stop.

g. Place new rubber check valves over the check valve springs and install in the
outlet
holes, spring
first.

Note:
When replacing a
complete
master cylinder
with a service unit, the original push rod must be used. The push rod retainer and snap ring retainer 12617

FIG.
P-14—REMOVING TUBE SEATS 1
—Screwdriver

2— No. 6-32 Self-Tapping Screw

3—
Tube
Seat must be removed and discarded. As the new unit
has the retainers installed it is only necessary to

install
the push rod until a "snap" is heard and the push rod is retained. 332

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

P h.
Install
the tube seats, flat side toward the check

valve,
and press in with tube nuts or the master

cylinder
brake pipe tube nuts.

BLEEDING
a.
Before the master cylinder is installed on the
car,
the unit must be bled.

b.
Support the cylinder assembly in a vise and

fill
both fluid reservoirs with approved brake fluid,

e.
Loosely install a plug in each
outlet
of the

cylinder.
Depress the push rod several times until

air
bubbles cease to appear in the brake fluid.

d.
Tighten the plugs and attempt to depress the piston. The piston travel should be restricted after
all
air is expelled.
e.
Install
the master cylinder on the car and bleed
the hydraulic lines at the wheel cylinder. Refer to
Par.
P-7.

P-21.
Wheel
Cylinder
Reconditioning
•
Refer to Fig. P-15.
Note:
Make sure a replacement brake cylinder
has the same part number as the original cylinder.

FIG.
P-15—WHEEL
BRAKE CYLINDER
1— Boot

2—
Piston

3—
Cylinder
Cup
4—
Cup
Spring
5—
Cylinder

6—
Bleeder
Screw
a.
To remove a wheel cylinder,
jack
up the vehicle

and
remove the wheel, hub, and
drum.
Disconnect
the brake line at the fitting on the brake backing
plate. Remove the brake
shoe
return spring which

will
allow the brake
shoes
at the toe to
fall
clear of the brake cylinder. Remove two screws holding
the wheel cylinder to the backing plate.
b.
Remove the rubber dust covers on ends of

cylinder.
Remove the pistons and piston cups and
the spring.

c.
Wash the parts in clean alcohol.

d.
Examine the cylinder bore for roughness or
scoring.
Check
fit of pistons to cylinder bore.
e. When reassembling the cylinder, dip springs, pistons and piston cups in brake fluid.
Install

spring
in center of the wheel cylinder.
Install

piston cups with the cupped surface towards the

spring
so that the flat surface
will
be against
the piston.
Install
pistons and dust covers.
f.
Install
wheel cylinder to the backing plate and connect brake line and install brake
shoe
return

spring.

g. Replace wheel, hub, and
drum.

h.
Bleed the brake lines (Par. P-7).

P-22. TROUBLE
SHOOTING

P-23.
Squeaky
Brakes

In
most cases, squeaks are entirely eliminated by

correct
adjustment of the brakes. Squeaks may be
caused however, by glazed linings, lining wore thin
to the point of
exposed
rivets or by vibration. A

drum
will
not vibrate when the brake is securing

uniform
contact over the entire lining surface, ex­
cept when due to improper conditions such as the
linings becoming glazed.
Glazed
surface of the

brake
linings may be removed by a stiff
wire
brush.
Occasionally
squeaks are caused by roughened
sur­

face of the
drum,
which can usually be remedied
by rubbing down with emery cloth and by wiping
the brakings surface clean. In extreme cases it may
be necessary to reface the drum in a lathe. Should
this be done, do not remove a metal thickness greater than .030" [0,762 mm.] - .060" [1,52 mm.]

overall
diameter.

P-24. Rattles
in
Brakes

See that the tension of the springs in the brakes

and
attached to the control system are sufficient to

return
brakes and brake mechanism to their normal
position.
Return
springs are so placed that they
keep all slack out of the control system by tension on all joints.

Brakes
will
not rattle inside the
drum
if the springs
holding the
shoes
are kept at the proper tension. 333

p

BRAKES
P-25.
SERVICE

SYMPTOMS
Brakes Drag
Brake
Shoes
Improperly Adjusted
Piston Cups Enlarged . . •.
«•
Mineral
Oil or Improper Brake
Fluid
in System. . .

Improper
Pedal Adjustment
Clogged Master Cylinder By-Pass Port...

One
Brake Drags
Brake
Shoe
Adjustment Incorrect
v Brake
Hose
Clogged.
Return
Spring Broken
Wheel Cylinder Piston
01
Cups
Defective.........
Loose or Damaged Wheel Bearings

Brake Grabs
—
Vehicle Pulls
to One
Side
Grease
or Brake
Fluid
on
Lining................
Dirt
Between
Lining
and Drum

Drum
Scored or Rough
Loose Wheel Bearings. .
Axle Spring Clips Loose
Brake
Backing Plate Loose

Brake
Lining
..

Brake
Shoe
Reversed
Tires
Under-Inflated -
Tires
Worn Unequally
Glazed
or Worn
Lining

Restricted Brake
Line

Excessive Pedal Travel
Normal
Lining
Wear

Lining
Worn Out ... .

Leak
in Brake
Line.

Scored Brake Drums
Incorrect
Brake
Lining.

Air
in Hydraulic System

Spongy Brake Pedal
Air
in
Lines.
Brake
Shoe
Adjustment Incorrect
Insufficient Brake
Fluid

Excessive Pedal Pressure
Grease
or Brake
Fluid
in
Lining

Shoes
Improperly Adjusted

Warped
Brake
Shoes
Distorted Brake Drums
Glazed
or Worn
Lining

Restricted Brake
Line
Faulty
Brake Cylinder Insufficient Brake
Fluid.

Squeaky Brakes
Shoes
Warped or Drums Distorted
Lining
Loose.....
Dirt
Imbedded in
Lining

Improper
Adjustment.

Oil
or Grease on
Lining
Glazed
or Worn
Lining.

Drum
Scored
DIAGNOSIS

PROBABLE
REMEDY

Adjust
Flush
all
lines
with Alcohol. Install new cups in wheel and Master Cylinders

Adjust
Master Cylinder Eye Bolt
Clean
Master Cylinder

Adjust
Replace Replace
Replace
Adjust
or Replace
Replace
Lining

Clean
with Wire Brush

Turn
Drum and Replace
Lining

Adjust
Tighten Tighten
Different Kinds on Opposite Wheels

Forward
and
Rear
Shoes
misinstalled
Inflate
Replace or Rotate Replace Linings

Locate
and Repair

Adjust

Replace
Locate
and Repair Replace or Regrind Replace

Fill
Master
Cylinder
— Bleed Lines
Bleed Lines
Adjust

Fill
Master Cylinder
Replace
Lining
Major
Adjustment
Replace
Replace or Regrind Replace Linings * .

Locate
and Repair
Repair
or Replace
Fill
Master Cylinder Replace
Replace
Wire
Brush or Replace

Adjust
Replace Linings Replace Linings

Turn
Drum and Replace Linings 334

Q

WHEELS
FIG.
Q-2—FRONT
WHEEL

ATTACHING
PARTS —
2-WHEEL-DRIVE

1—
Steering
Knuckle

2—
Brake

3— Hub
Grease
Seal
4—
Inner
Bearing
Cone

5—
Inner
Bearing
Cup
6—
Hub
and
Drum

7—
Outer
Bearing
Cup
8—
Outer
Bearing
Cone
9—
Tongued
Washer

10— Nut
11—
Cotter
Pin

12—
Grease
Cap

13— Nut
14—
Lockwasher
15—
Bolt
j
10703
is ir 10730
FIG.
Q-3—REAR
WHEEL
ATTACHING PARTS —
4-WHEEL-DRIVE
TAPERED
AXLE

1—
Oil
Seal

2—
Cone
and
Rollers

3— Cup
4—
Shims
5—
Bearing
Retainer
6—
Brake
Backing
Plate
7—
Gasket

8—
Grease
Retainer

9—
Grease
Protector

10—Bolt
11— Hub
and
Drum

12—
Shaft
Key

13—
Washer

14—
Nut
15—
Cotter
Pin
Ifi—Hub
Cap

17—Nut

18—
Ixick
Washer

19—Bolt

FIG.
Q-4—REAR
WHEEL

ATTACHING
PARTS —
2-WHEEL-
DRIVE-TAPERED
AXLE

1—
Oil
Seal

2—
Bearing
Cone

3—
Bearing
Cup
4—
Shim
Set
5—
Retainer
and
Seal

6—
Brake
7—
Nut

8—
Hub
and
Drum

9—
Axle
Shaft Key

10—
Washer

11— Nut
12—
Cotter
Pin
13—
Lockwasher

14—
Bolt

recommended with the exception that
rear
wheels

on vehicles having
Trac-Lok
or
Powr-Lok
axles
should always be removed for balancing.

Q-3. WHEEL
BEARING
SERVICE

Adjustment
of the wheel bearings is
critical
be­ cause it establishes the running clearance of the wheel bearings. Wheel bearing adjustment that is
too
tight
preloads the bearings and causes them
to run hot. Loose wheel bearings permit the drum hub to shift its position on the bearings as thrust loads
vary
with acceleration,
braking,
and cornering.

Loose
bearings also cause
erratic
braking.
To check
the wheel bearings for adjustment, brakes must
be free and in fully released position. 336

Q

WHEELS

FIG.
Q-6—REAR
WHEEL,
FLANGED
AXLE
AND
BEARING
ASSY.

1—
Retainer
Plate

2— Oil
Seal

3—
Unit
Bearing

4—
Retaining
Ring
5—
Axle
Shaft
wheel
will
turn
freely with no drag. If adjustment
is necessary, follow the procedure given in Par. Q-8.

Q-8.
Rear Wheel Bearing Adjustment
—
Tapered Axle

The
bearing adjusting shims are placed
between
the brake backing plate and axle flange as shown

in
Fig. Q-7.

With
wheel raised on
jack,
the following procedure
should be used to make the
rear
wheel bearing
adjustment.

a.
Remove the hub cap with hub cap puller, the
cotter pin, axle shaft nut, and washer. Remove the
wheel hub and drum with a wheel puller.

b.
Disconnect hydraulic brake line at wheel

cylinder.

c.
Remove the
bolts
holding the brake dust shield, grease and bearing retainer, and the brake backing
plate.

d.
Remove or install shims to adjust the bearings
to provide .001" to .006" [0,025 a 0,152 mm.]
end float of the axle shaft.

Note:
Before reassembly of the wheel make certain
the backing plate nuts are tight and torqued at 25 to 35 lb-ft [3,4 a 4,8 kg-m.].
e. Reassemble the wheel, adjust brakes, and check
the bearing adjustment (Par. Q-7).

0-9.
REAR WHEEL MOUNTING
—
TAPERED AXLE

Proper
axle shaft key installation is accomplished by placing the hub and drum on the axle shaft
taper and then inserting the axle shaft key in the
FIG.
Q-7—REAR
WHEEL
AND HUB
BEARING
—

TAPERED
AXLE
SHAFT

1—-Adjusting
Shims
2—Inner
Seal
3—Outer
Seal
keyway.
Never install the key in the keyway before

placing
the hub and drum assembly on the axle
shaft. Be sure that the axle shaft nut is torqued
to a minimum of 150 lb-ft. [20,7 kg-m.].
O-10.
BRAKE
DRUM
SERVICE
On
rear
wheels, the hub fits inside the brake drum
(Fig.
Q-3). On front wheels, the hub is attached
to the outside of the brake drum (Fig. Q-l). The

brake
drums are attached to the wheel hubs by
five serrated bolts. These
bolts
are also used for
mounting the wheels on the hub. To remove a

brake
drum,
press or drive out the serrated
bolts
and
remove the drum from the hub. When placing
the drum on the hub, make sure that the contacting
surfaces are clean and flat.
Line
up the
holes
in
the drum with
those
in the hub and put the drum
over the shoulder on the hub. Insert five new
serrated
bolts
through the drum and hub and drive
the
bolts
into place solidly. Place a round head of the bolt in a vise. Next, place the hub and drum
assembly over it so that the bolt head rests on it.

Then
swage
the bolt into the countersunk section of the hub or drum with a punch. The runout of
the drum face should be within .030" [0,76 mm.]
total indicator reading. If the runout is found to be greater than .030" it
will
be necessary to reset
the
bolts
to correct the condition.
0-11.
TIRE SERVICE
Refer
to Fig. Q-8.

One
of the most important factors of safe vehicle
operation is systematic and correct tire mainte­ nance.
Tires
must sustain the weight of a loaded vehicle, withstand more than ordinary rough serv- 338

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

Q
ice, provide maximum safety over all
types
of

terrain,
and furnish the medium on which the
vehicle can be maneuvered with ease. Although
there are other
elements
of tire service, inflation maintenance is the most important and in many
instances the most neglected. The tire pressure should be maintained for safe operation. An under- inflated tire is dangerous as too much flexing can
cause breakage of the casing. Overinflation in time
may
cause a blowout.

Upon
careful inspection of tires, it may be found
that improper wheel alignment, balance, grabbing
brakes,
poor driving habits, fast cornering or other
conditions are the cause of wear. Such conditions
should be corrected.

a.
UNDERINFLATION

Underinflation
distorts the normal contour of the
tire
body and the tire
bulges
or "bellies out" with

an
extreme flexing action.
This
wears the tread at the
edges
more than the center and generates
excessive internal heat, weakening the cords and
resulting
in bruises, broken cords or ply separation.

Underinflation
also leads to rim bruises as in­ sufficient resistance is provided to prevent the tire

from
being jammed against the rim and crushed
or
cut when the tire strikes a
curb,
rock, or rut.

b.
OVERINFLATION

When
a tire is
overinf
lated,
increased tension caused by excessive pressure prevents proper deflection of
the sidewalls.
This
results in wear in the center of the tread and the tire also
loses
its ability to absorb

road
shocks. Under this increased
strain,
cords in the tread area eventually snap under impact, caus­ing a casing break.

c.
MISALIGNMENT
WEAR
Excessive
wheel camber causes the tires to run at an angle to the road when camber is incorrect

it
will
cause excessive wear on one side of the
tire
tread.

Front
wheels should be straight ahead or toe-in slightly. When there is excessive toe-in or
toe-out,

tires
will
revolve with a side motion and scrape
the tread rubber off.
Front
tires
will
show wear on the outside with too great a toe-in condition
and
on the inside with a
toe-out
condition.

d.
BALANCE
Cupping
and bald spotting of tires is associated

with
wear on a vehicle driven mostly at high-way
speeds
without the recommended tire rotation and

with
unbalance conditions.

Q-12.
Tire
Care
Note;
For satisfactory 4-wheel drive operation, a
4-wheel drive vehicle
MUST
be equipped with the same size tires of equal circumference on all
four wheels. The tires must then be inflated to

proper
factory recommended pressures at all times.

Tire
pressure, tire rotation, wheel balance, and wheel alignment are the four vital factors that in­
fluence the
extent
of tire life and the
ease
and safety of vehicle control.
Four
of the most common

tire
troubles are:

a.
Excessive wear around the outer
edges
resulting

from
underinflation.

b.
Excessive wear in the center of the tread re­
sulting from overinflation.

c.
Tire
tread worn on one side indicating wheels
need realigning.
d.
Cuplike
depressions on one side of the tread

indicating
wheels need balancing.

If
the vehicle normally carries a
full
load, two to
four psi. [0,14 a 0,28 kg-m2] can be added to the
recommended air pressures. But, remember that adding air with a light load means a harsher ride,

doesn't
help tires, and wears out shock absorbers. Rotate the tires as shown in Fig. Q-9 for correct
rotation system.

Q-13.
Tire
Removal
and
Installation

To
remove a tire from a drop center rim, first
WEAR
AT SHOULDERS

WEAR
AT CENTER

WEAR
ON ONE
SIDE
FEATHERED
EDGE
BALD
SPOTS

/1TTDN

i

UNDER
INFLATION
OVER
INFLATION
EXCESSIVE
CAMBER

INCORRECT
TOE
WHEEL
UNBALANCED

liF
11

ADJUST
PRESSURE TO
SPECIFICATIONS
WHEN
TIRES ARE
COOL
ADJUST
CAMBER
TO

SPECIFICATIONS
ADJUST
FOR

TOE-IN
DYNAMIC
OR
STATIC

BALANCE
WHEELS

FIG.
Q-8—TIRE
WEAR
PATTERN
339

u
MISCELLANEOUS
U-12.
STANDARD
AND
RECOMMENDED TOOLS
(Continued)

Tool
Description
CLUTCH

W-296 Fixture — Adjusting

TRANSMISSION

C-3201
- A
Lo-Jack
— Floor Type

AXLE

C-637 Puller — Axle Shaft & Oil Seal

STEERING

DD-428 Gauge — Camber & Caster
DD-435 Turntables — Wheel Alignment C-3479 Gauge & Scribe — Toe-in Checking

BRAKES

C-416 Clamps — Brake Cylinder Retaining C-3080 Hone — Brake Cylinder
C-3496-B Bleeder — Hydraulic Pressure Type C-3785 Remover & Installer — Brake Return Spring
C-3920 Micrometer — Brake Drum Checking
U-13.
ENGINE TORQUE SPECIFICATIONS HURRICANE
F4
ENGINE

Pounds - Feet
kg-m.

30-40
4,1
a

5,5

Camshaft
Thrust Plate Bolt
20-26

2,8
a
3,6

Clutch
Control
Ball
Stud — [7,93 mm.]
35-45

4,8
a
6,2
Connecting Rod Cap Bolt Nut — y8" [9,53 mm.|
35-45

4,8
a
6,2

60-70
8,3
a
9,7

Cylinder
Head to Block Bolts
60-70
8,3
a
9,7

45-55
6,2
a
7,6

29-35
4,0
a
4,8

Flywheel
to Crankshaft Bolt. 35-41
4,8
a

5,7

Fuel
Pump Mounting Bolts 13-17 1,8
a
2,4
Alternator Bracket to Cylinder Block.
25-35
3,5
a
4,8

29-35
4,0

a
4,8

Main
Bearing
Caps.
.
65-75
9,0
a
10,4

Oil
Pan
Drain
Plug
25-35

3,5
a

4,8
9-14 1,2
a

1,9
Piston Pin
Lock
Bolt 35-41
4,8
a

5,7

30-36
4,1
a

5,0

Spark
Plugs to Cylinder Head
25-33

3,5
a
4,6
Starting Motor Mounting Bolt.
20-25
2,8
a
3,5
7-10 0,9
a
1,4

Water
Outlet Elbow to Cylinder Head
20-25
2,8

a
3,5

Water
Pump to Cylinder Block 12-17
1,7
a

2,4

NOTE:
Turn
the connecting rod cap nut locks (inverted type, pressed
steel)
finger
tight
and then
tighten
% turn more with wrench
362

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

ALPHABETICAL INDEX

SUBJECT PAR.
SUBJECT
PAR.

Abbreviations,
List
U-17 Accelerator Linkage E-70
Air
Cleaner B-25, B-26, B-82, C-21, E-69

Air
Delivery Manifold Fl-4, F2-12
Air
Filter, Pump • F2-3, F2-11

Air
Injection Tubes Fl-5, F2-13
Air
Pump Fl-2, F2-10
Alternator Bearings B-76, H-80
Alternator Brushes H-74, H-75
Alternator Charging System •
•
H-63
Alternator
Diodes
H-69, H-85
Alternator Precautions H-64 Alternator Rotor H-76, H-79
Alternator Tests H-67, H-77 Alternator Specifications H-l 52
Alternator Stator H-84
Anti-Backfire
Valve Fl-6, F2-14
Antifreeze
Chart
• G-22 Antifreeze
Solutions
- G-16
Axle Camber O-l
Axle Caster 0-8

Back-Up
Lights H-135

Ballast
Resistor. H-32 Battery C-3, H-2 Bendix Folo-Thru Drive H-105, H-106
Bleeding Brakes P-7
Body T-l Body Lubrication. B-65 Body Name Plates ' A-7

Brake
Adjustment P-14
Brake
Drums. • .P-17

Brake
Hoses
P-8

Brake
Maintenance . P-5
Brake
Master Cylinder B-40, P-2, P-20

Brake
Service P-6
Brake
Wheel Cylinder • P-21

Camber
Adjustment 0-7
Camshaft D-6, D-51, D-52, D-53, D-81, Dl-26, Dl-33, Dl-55, Dl-80

Carburetor
E-10, E-25

Carburetor
Adjustment C-25, E-14, E-40,
Fl-13,
F2-16
Carburetor
Specifications .Fl-38, F2-34, E-79

Caster
Adjustment 0-8

Charging
System Service. .H-34, H-63

Chassis
Lubrication B-7, B-83

Chassis
Torque Specifications U-14

Clutch
1-4, MO
Clutch
Adjustment 1-3
Clutch
Linkage B-44, 1-3

Clutch
Maintenance .. 1-2
Clutch
Release Bearing B-74, 1-25

Coil
C-20, H-19, H-31 Connecting Rod Bearings D-47, D-48, D-49, Dl-49 Connecting Rod
Crank
Pins D-42
Connecting Rods... .D-20, D-50, D-95, Dl-31, Dl-45, Dl-75
Controls B-59, B-62
Cooling System B-28, G-l Cooling System Filling G-2

Core
Hole Expansion Plugs D-72

Crankcase
Ventilating System B-13, C-6, D-110

Crankshaft
D-26, D-38, D-39, Dl-38, Dl-73
Crankshaft
End Play. D-83, Dl-74

Crankshaft
Main Bearing D-43, D-44, Dl-32, Dl-40, Dl-73

Crankshaft
Oil Seal, Front Dl-21, Dl-85
Crankshaft
Oil Seal, Rear D-63, D-85, Dl-72

Cylinder
Block D-32, Dl-34

Cylinder
Bores D-35, Dl-36

Cylinder
Head D-17, D-73, D-98, Dl-24, Dl-63, Dl-82

Cylinder
Head Torque. C-5
Dash Pot Adjustment C-26, E-44
Differential B-51 thru B-53, N-9 Differential Adjustments N-16, N-18
Differential, Powr-Lok N-20
Differential,
Trac-Lok
N-24
Directional Signal Lights. . H-138
Distributor B-14, B-15, C-10, D-13, Dl-9, H-9, H-20 Distributor Check H-l7, H-28
Distributor Point Dwell C-17 Distributor Resistance Test C-16

Drawbar
.R-6, U-16
Dual
Brake System P-l thru P-26

Electrical
Instruments H-l22

Electrical
Specifications .H-l52

Electrical
System H-l Engine .
..D-l,
Dl-1
Engine Code Number A-6
Engine Compression .
.
C-9 Engine Disassembly . • .D-6, Dl-5 Engine Installation D-105, Dl-102
Engine Lubrication System B-4, B-6 Engine Mountings D-3, Dl-3
Engine Oil B-9
Engine Oil Filter B-10, B-ll,
D-lll,
Dl-13, Dl-93
Engine Oil Pan D-l9, D-66, D-97, Dl-29, Dl-51, Dl-77 Engine Oil Pump. . .D-14, D-65, D-93, Dl-19, Dl-50, Dl-87
Engine Overheating. G-l9 Engine Removal D-5, Dl-4.

Exhaust
Emission Control — F4 Fl-1 thru Fl-30
Exhaust
Emission Control — V6 F2-1 thru F2-36
Exhaust
Manifold, Install F-6

Exhaust
Pipe -
•
F-8

Exhaust
System F-2, F-3

Exhaust
System Maintenance F-4

Fan
Belt C-27, Dl-11, Dl-96, G-18
Floating Oil Intake. D-64, Dl-30, Dl-50, Dl-76 Flywheel D-25, D-67, D-87, Dl-28, Dl-52, Dl-78
Flywheel Housing. D-71, D-88, Dl-27, Dl-54, Dl-79
Flywheel Pilot Bushing D-70, 1-8

Frame
R-l

Frame
Alignment. R-2
Frame
Dimensions R-3
Frame
Straightening R-4

Front
Bumper Weight. • U-9
Front
Axle B-50, M-2

Front
Axle Alignment R-5

Front
Axle Installation • M-12
Front
Axle Maintenance M-3

Front
Axle Shaft Removal M-5

Front
Axle U-Joint B-54, B-55, M-7

Front
Axle Steering Knuckle M-&

Front
Wheel Alignment 0-4

Front
Wheel Bearings B-56, B-57, Q-4
Front
Wheel Toe-in 0-5, 0-6

Front
Wheel Turning Angle 0-9
Fuel
Gauge Float Unit F-76

Fuel
Lines - E-77

Fuel
Pump E-45, E-54, E-60, E-67
Fuel
Pump Check C-23

Fuel
Tank
E-72

G

Gauges, Testing H-l24

General
Specifications A-8
Generator B-16, H-34 thru H-40

Glass
Replacement • T-4
Governor. . .
•.
• U-3
Guides, Valve D"61

H

Hazard
Warning Lights H-139
Head Lamp Aiming H-131, H-132 Head Lamp Replacement H-130
Headlight Dimmer Switch H-l
2
7

Heat Control Valve C-7, F-7 Heated Air System • •
•
F2-2
Heater U-10
Horns.....
....H-137 371