1953 JEEP DJ oil reset

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

m
FRONT fiXLE

Contents

SUBJECT
PAR.

GENERAL.
M-l

4-WHEEL DRIVE FRONT
AXLE.
M-2
Maintenance
Requirements M-3

FRONT AXLE REMOVAL
.M-4

AXLE
SHAFT REMOVAL
M-5

REMOVING
AND
OVERHAULING
DIFFERENTIAL
.M-6

AXLE
SHAFT UNIVERSAL JOINT SERVICE
M-7

STEERING
KNUCKLE SERVICE
M-8
Replacing
Steering
Knuckle
Oil Seal M-10

M-1. GENERAL
The
front axle for all 'Jeep* Universal models,

which
have 4-wheel drive, is described in
Par.
M-2.
The
front axle for all DJ-5, DJ-6 models, which
have 2-wheel drive, is described in
Par.
M-l5.

M-2. 4-WHEEL-DRIVE FRONT AXLE
The
front axle is a live driving unit with hypoid

type
driving gears and spherical steering knuckles mounted m pivot pins which ride on tapered roller bearings for
ease
of steering. The drive is of the
full
floating
type
through axle shafts built integrally

with
cardan cross universal joints which revolve in the steering knuckles. The steering knuckle tie rod

arm
is made integrally with the knuckle. The
knuckles
are connected by a divided tie rod to a steering bell
crank.
A steering connecting rod con­

nects
the bell
crank
to the steering gear arm. The

divided
tie rod is adjustable and the
toe-in
of each
front wheel is adjusted independently.
Camber
and
SUBJECT
PAR.

REASSEMBLY
AND
BEARING PRELOAD
M-9

AXLE
SHAFT INSTALLATION
M-ll
FRONT AXLE INSTALLATION........
.M-l2
Turning
Angle Adjustment . .M-14

Steering
Tie Rod and
Beilcrank
M-l3

2-WHEEL DRIVE FRONT AXLE
M-15
Removal
of Solid
Front
Axle M-l6

Steering
Knuckle
Service M-l7

Steering
Knuckle
Pin Replacement. ......M-l8

SERVICE
DIAGNOSIS
M-19

AXLE
SPECIFICATIONS.
M-20

caster
of the front
wheels
is preset.
Camber
cannot
be altered but caster can be adjusted by installing

caster
shims
between
the axle pad and the springs.

For
information on the steering
geometry
see
"Steering
Section."

Service
procedures given in this section include
the removal, installation, disassembly and assembly
of the Model
27AF
front axle assembly, the axle
shafts, steering knuckles, and
universal
joints.

Note:
All service replacement axle assemblies are
shipped from the factory without lubricant in the
differential.
Lubricant
must be added; use grade

and
quantity as specified in the lubrication chart (Section B).

M-3.
Maintenance Requirements

A
spring-loaded breather is located on the top of
the differential housing.
Each
time the differential
lubricant
is checked, the breather should be

STEERING
SYSTEM

O-L
GENERAL

The
steering system on all Jeep Universal vehicles
consists of the steering gear, steering wheel, steering column and shaft, and steering linkage.
This

section covers wheel alignment, steering linkage,
steering gear, steering column and steering wheel.
0-2. Steering
Gear
Function

The
steering gear is a reducing gear. It exchanges a

relatively
large amount of movement with a small force (applied by the driver at the steering wheel), for a much smaller amount of movement with a
greatly increased force through a cam and lever
action type steering gear. The steering gear ratio is 17.9 to 1 on vehicles equipped with the F4
engine

and
19 to 1 with the V6 engine.
0-3. Steering
Linkage
Refer
to Fig. O-l.
The
steering linkage consists of a steering arm at­
tached to the steering gear, a steering connecting

rod,
(drag
link),
connecting the steering arm to the
beilcrank,
and a steering tie rod connecting the
beilcrank
to the axle tie rod. The beilcrank pivots
on a pin mounted just to the left of the frame front crossmember. The steering tie rod is connected to
the beilcrank and
extends
to the right
ball
joint as­ sembly of tie rod. The tie rod
extends
to the wheels,
being connected to their respective steering knuckle

arms
at the wheels.
With
this linkage arrangement,
as the steering arm
moves
rearward,
the front
wheels
turn
to the left. As the steering arm
moves
forward,
the wheels
turn
to the right.
Ball
joints are used to secure the drag
link,
steering
connecting rod and tie rod ends. The
ball
joints
assist in maintaining
good
steering control and con­
stant toe-in of the front wheels under all driving conditions. If the
ball
joints
become
worn enough
to allow free motion in the linkage, they should be,

replaced.

Note:
Ball
joint replacement of the tie rod requires
resetting of the wheel toe-in adjustment.
0-4.
Steering
Column
and Gear
Alignment
When
adjusting a steering gear remove all loads
from
the unit by disconnecting the steering con­
necting rod (drag
link)
from the steering arm and
also
loosen
the instrument panel bracket and the
steering gear to frame
bolts
to allow the steering
post
to correctly align itself. When retightening the
steering gear to frame
bolts
use a torque wrench
pull
of 45 to 55 lb-ft. [6,2 a 7,6 kg-m.] on the

Vk*
bolts
and 30 to 40 lb-ft. [4,15 a 5,5 kg-m.] on the
Vs"
bolts. 10811

FIG.
0-2—STEERING
GEAR
1—Nut

2
—Lockwasher

3—
Steering
Gear
Arm 4—
Lever
Shaft Oil Seal
5—
Outer
Housing Bushing
6—
Inner
Housing Bushing 7—
Filler
Plug
8—
Cover
and Tube
9—
Ball
Retaining
Ring

10—Cup
11—
Ball
(Steel)
12—
Tube
and Cam
13—
Shims

14—
Upper
Cover

15—
Lockwasher

16—
Bolt

17—
Steering
Wheel 18—
Horn
Button Retainer
19—
Horn
Button
20—
Horn
Button Cap 21— Nut
22—
Spring
23—
Spring
Seat
24—
Bearing
25—
Horn
Cable

26—
Horn
Button Spring
27—
Spring
Cup
28—
Steering Column
29—
Oil
Hole
Cover

30—
Clamp
31—
Adjusting
Screw
32— Nut
33—
Bolt

34—
Side
Cover
35—
Gasket

36—
Shaft
and
Lever

37—
Housing
314

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

The
purpose of caster Fig. O-S, is to provide steer­
ing stability which
will
keep the front wheels in the
straight
ahead position and also assist in straighten­
ing up the wheels when coming out of a
turn.
Caster
of the front wheels is preset. If the angle of

caster,
when accurately measured, is found to be

incorrect,
correct it to the specification given at
the end of this section by either installing new

parts
or installing caster shims
between
the axle

pad
and the springs.

If
the camber and toe-in are correct and it is known
the the axle is not twisted, a satisfactory check

may
be made by testing the vehicle on the road.
Before road testing, make sure all tires are properly

inflated,
being particularly careful that both front
tires are inflated to exactly the same pressure.
If
vehicle turns easily to either side but is
hard
to
straighten out, insufficient caster for easy handling of vehicle is indicated. If correction is necessary, it

can
usually be accomplished by installing shims

between
the springs and axle pads to secure the
desired
result.
0-11-
Front
Wheel
Turning
Angle
When
the front wheels are turned, the inside wheel
on the
turn
travels in a smaller circle than the out­side wheel, therefore, it is necessary for the wheels
to toe out to prevent the tire on the inside wheel

frOm
being scuffed sideways.
This
angle for toe out
on turns is designed to permit both front wheels to

turn
on a common center by having the ends of the
steering
knuckle
arms closer
together
than the king­

pins.

To
avoid possible damage to the universal joints
on the front axles of 4-wheel drive vehicles, it is advisable to check the turning angle.
Wearing
away
of the upset
edge
on the spindle housing bolt which
10607

FIG.
0-6—TURNING
ANGLE
STOP
SCREW
1—Stop
Screw
contacts the
stop
screw
will
increase the turning
angle to the point where the universal joints may
be damaged.

The
Jeep Universal Series vehicles should have a

turning
angle of not more than 27^° both left and

right.
To adjust the
stop
screw, it is necessary to

loosen
the locknut holding the
stop
screw. When
the adjustment has been made, tighten the locknut
on the screw to prevent any movement. Refer to
Fig.
O 6.

The
left steering knuckle arm controls the relation­
ship of the front wheels on a left
turn
and the right
arm
controls the relation on a right
turn.

0-12. Steering
Knuckle
Arm

Should
a steering knuckle arm
become
bent, the

knuckle
housing must be replaced. It is not safe to
straighten the knuckle arm.
0-13.
Front
Wheel
Shimmy
Wheel
shimmy may be caused by various condi­
tions in the wheels, axle or steering system, or a
combination of
these
conditions. Outlined below

will
be found the usual corrections of this fault:

a.
Equalize
tire pressures and see that they are
according
to specifications.

b.
Check
the wheel bearings for
looseness.
Be sure
that the inner wheel bearing race is not too
loose
on the spindle.

c.
Remove both steering knuckles and carefully inspect the upper and lower king pin bearings.

Inspect
the bearing cups for evidence of brinelling,
pitting, or fretting. Any bearings that show the slightest imperfection must be
replaced.
Reassemble

and
lubricate the front axle and steering linkage,
installing
new steering knuckle oil seals if present
seals show any wear.

d.
With
full
weight on the front wheels and one

man
working the steering play with the steering
wheel, a second man should closely observe the steering bell
crank
for any rocking motion and the
double tie rod socket for any rocking motion or

looseness
at both points. Replace the complete bell
crank
assembly if it has even the slightest rocking motion. The same applies to the double tie rod
socket.
e.
Check
wheel run-out.
This
check should include
radial
run-out and wheel
looseness
on the hub.
f- Test wheel balance—check for blowout patches,
uniform
tire tread, vulcanized tires, mud on inside
of wheels, and tires creeping on the
rims.

g.
Try
switching front wheels and tires to the
rear,
criss-crossing
them in this operation.

h.
Check
for front
spring
sag. Also check for broken

spring
leaves, broken center
spring
bolt,
loose
spring

clips
(or tight clips), over-lubrication of spring leaves, spring shackle bracket
loose
on frame, and

loose
rear
spring shackle. Be sure that the shock
absorbers
are operating properly to eliminate bob­bing of the front end.

i.
Check
brakes to make sure that one
does
not

drag.

j.
Check
the steering assembly and steering con­ necting rod.
This
includes the up-and-down-play
of the steering worm shaft, end play of the cross 317

Q

WHEELS

FIG.
Q-6—REAR
WHEEL,
FLANGED
AXLE
AND
BEARING
ASSY.

1—
Retainer
Plate

2— Oil
Seal

3—
Unit
Bearing

4—
Retaining
Ring
5—
Axle
Shaft
wheel
will
turn
freely with no drag. If adjustment
is necessary, follow the procedure given in Par. Q-8.

Q-8.
Rear Wheel Bearing Adjustment
—
Tapered Axle

The
bearing adjusting shims are placed
between
the brake backing plate and axle flange as shown

in
Fig. Q-7.

With
wheel raised on
jack,
the following procedure
should be used to make the
rear
wheel bearing
adjustment.

a.
Remove the hub cap with hub cap puller, the
cotter pin, axle shaft nut, and washer. Remove the
wheel hub and drum with a wheel puller.

b.
Disconnect hydraulic brake line at wheel

cylinder.

c.
Remove the
bolts
holding the brake dust shield, grease and bearing retainer, and the brake backing
plate.

d.
Remove or install shims to adjust the bearings
to provide .001" to .006" [0,025 a 0,152 mm.]
end float of the axle shaft.

Note:
Before reassembly of the wheel make certain
the backing plate nuts are tight and torqued at 25 to 35 lb-ft [3,4 a 4,8 kg-m.].
e. Reassemble the wheel, adjust brakes, and check
the bearing adjustment (Par. Q-7).

0-9.
REAR WHEEL MOUNTING
—
TAPERED AXLE

Proper
axle shaft key installation is accomplished by placing the hub and drum on the axle shaft
taper and then inserting the axle shaft key in the
FIG.
Q-7—REAR
WHEEL
AND HUB
BEARING
—

TAPERED
AXLE
SHAFT

1—-Adjusting
Shims
2—Inner
Seal
3—Outer
Seal
keyway.
Never install the key in the keyway before

placing
the hub and drum assembly on the axle
shaft. Be sure that the axle shaft nut is torqued
to a minimum of 150 lb-ft. [20,7 kg-m.].
O-10.
BRAKE
DRUM
SERVICE
On
rear
wheels, the hub fits inside the brake drum
(Fig.
Q-3). On front wheels, the hub is attached
to the outside of the brake drum (Fig. Q-l). The

brake
drums are attached to the wheel hubs by
five serrated bolts. These
bolts
are also used for
mounting the wheels on the hub. To remove a

brake
drum,
press or drive out the serrated
bolts
and
remove the drum from the hub. When placing
the drum on the hub, make sure that the contacting
surfaces are clean and flat.
Line
up the
holes
in
the drum with
those
in the hub and put the drum
over the shoulder on the hub. Insert five new
serrated
bolts
through the drum and hub and drive
the
bolts
into place solidly. Place a round head of the bolt in a vise. Next, place the hub and drum
assembly over it so that the bolt head rests on it.

Then
swage
the bolt into the countersunk section of the hub or drum with a punch. The runout of
the drum face should be within .030" [0,76 mm.]
total indicator reading. If the runout is found to be greater than .030" it
will
be necessary to reset
the
bolts
to correct the condition.
0-11.
TIRE SERVICE
Refer
to Fig. Q-8.

One
of the most important factors of safe vehicle
operation is systematic and correct tire mainte­ nance.
Tires
must sustain the weight of a loaded vehicle, withstand more than ordinary rough serv- 338