1953 JEEP DJ light

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

I thickness: .285"
[0,724
cm.], .305"
[0,775
cm.].

Each
spacer should be hardened and ground to size, and then have the dimensional thickness
stamped thereon.

c.
From
flat bar stock at least Vfe" [3 mm.] thick,
make a
gauge
as shown in Fig. 1-22. Harden, grind
to size, and stamp sizes on the
gauge.

1-27.
Clutch Installation

a.
Very
sparingly, apply wheel bearing lubricant
to inner surface of pilot bushing in crankshaft.

Caution:
If
excessive
lubricant is applied to pilot bushing, it
will
run out on face of flywheel when
hot and
ruin
the driven plate facings.
b. Make sure that splines in the driven plate hub
are
clean; apply a light coat of lubricant to splines
of hub and transmission drive gear shaft. Slide plate over gear shaft several times; remove plate
from shaft and wipe off
excess
lubricant.

Caution:
Driven plate facings must be kept clean

and
dry.

c.
Fill
groove
in throwout bearing collar with wheel bearing lubricant. See Fig. 1-23. Make sure
that front bearing retainer of transmission is clean;
apply a light coat of wheel bearing lubricant. Slide
throwout bearing over bearing retainer several times. Remove bearing from retainer and wipe off

excess
lubricant.

12736
FIG.
1-23—LUBRICATION
POINTS
—

CLUTCH
THROWOUT
BEARING
COLLAR

1—Coat
This
Groove 2—Pack
This
Recess
d.
Clean
and apply wheel bearing lubricant to ball
stud in flywheel housing and to the
seat
in clutch

fork.

e.
If disassembled, install pressure plate in the cover assembly, lining up the
groove
on its
edge

with the
groove
on the
edge
of the cover.
Install

pressure plate retracting springs, and the three
drive
strap-to-pressure plate
bolts
and lock washers.

Torque
bolts
11 lb-ft. [1,51 kg-m.].

Note:
The diaphragm
type
clutch assembly is fac­
tory calibrated and requires no adjustment
before
installation. Refer to Par. 1-14 to adjust Borg and

Beck
coil spring
type
clutch assembly.
f.
Install
the pressure plate and driven plate on
flywheel. Support both assemblies with a spare
main
drive gear.

Note:
Be certain that
mark
on clutch cover is
aligned with the
mark
made on the flywheel during
clutch removal.
g.
Install
clutch attaching
bolts
and tighten alter­ nately so that clutch is drawn squarely
into
position
on flywheel.
Each
bolt
must be
tightened
one turn at a time to avoid bending the clutch cover flange.

Torque
bolts
30 to 40 lb-ft. [4,1 a 5,5 kg-m.].

h.
Lubricate
the ball stud and clutch fork with
wheel bearing lubricant and install clutch fork.

Note:
Be certain that fork retaining spring is
tight

on pivot ball stud.

i.
Install
flywheel housing on
engine
cylinder
block.

Caution:
Be certain that dowel pins are installed

in
cylinder block.

j.
Lubricate
the recess on the inside of the throw-
out bearing collar. Be careful not to use too much
lubricant.
See Fig. 1-23.

Caution:
Make certain that the lips of the spring
retainer (attached to the clutch fork) are in
groove
of the bearing. See Fig. 1-24.
k.
Install
throwout bearing assembly and connect
clutch linkage.
I.
Install
transmission as described in Section J. m. Adjust clutch for %"
[19,05
mm.] free travel,
see
Par.
1-3. 235

THREE-SPEED
TRANSMISSION

FIG.
J-l—TRANSMISSION

REMOTE
CONTROL
CJ-5
A,
CJ-6A

1— Stop Screw
2—
Bias
Spring

3—
Gearshift
Lever
4—
Lever
Ball

5—
Steering
Wheel 6—
Horn
Button 7—
Column
and Bearing
8—
End
Huts
9—
Shift
Rod
Ends

10—
Shift
Rod
11—
Shift
Rod
12—
Cross-Shift
Bracket

13—
Control
Shaft
14—
Lubrication
Fitting
15—
Lever
and
Clutch

16—
Adjusting
Yoke

17—
Aligning
Rod 11706

b.
Remove gearshift lever fulcrum pin and the
gearshift lever.

c.
Remove plates on the toe board at the steer­
ing
post.

d.
Remove two screws holding remote control
housing to the steering
post
and lift the housing
from
the positioning pin.

e.
Remove the assembly down through the floor
pan.

f. Remove the lower clutch and shift lever from the housing by turning counterclockwise.
g. Remove upper clutch and shift lever in the same

manner.

h. Wash all parts in a suitable cleaning solution.

J-5.
Reassembly of
Remote
Control
•
Refer to
Fig.
J-l

Check
clearance of shift dog which
engages
in slot
of clutches, and if found to be greater than .009" [0,229 mm.] clearance, replace the worn parts.
Assemble upper clutch lever assembly in housing
making
sure that the alignment
hole
in the housing
faces toward the engine.
Turn
the upper lever as­
sembly in as far as it
will
go and then back off one

full
turn
until the
hole
in the clutch lever aligns

with
hole
in the housing.
Assemble the lower clutch lever assembly in hous­ ing until faces of clutches contact then back off
not more than one-half
turn
which should bring
the aligning
hole
in the lever in line with the
hole
in
the housing. If the one-half
turn
does
not bring
the alignment
hole
in proper position, it
will
be
necessary to grind off (square with axis not to exceed .015") [0,397 mm.] the face of the lower

clutch;
in other words, backing off not more than
one-half
turn
from face to face contact
gives
the

proper
clearance of .015" to .031"
[0,397-0,794
mm.]

between
the two clutches.
Assemble the unit to the steering
post
in reverse

order
of dismantling and adjust remote control

rods.
After
assembly, if the shift dog catches on the
edge

of the slot in the clutch when moving the lever up

and
down, disconnect the shift rod at the
transmission
end and either lengthen or shorten it
slightly to correct this condition.

J-6.
TRANSMISSION
REMOVAL
The
following repair procedures given in Par. J-7
through J-ll for the standard
3-speed
transmission
apply
in general to all models listed. Minor dif­
ferences
between
models that affect the procedure

are
noted. Procedure for the optional
4-speed
trans­mission
begins
with Section
J-l.

Removal
is as follows:

a.
Drain
the transmission and transfer case. Re­ place the
drain
plugs.

b.
Remove the floor pan inspection plate.

c.
Remove the shift lever and shift housing as­ sembly and its gasket from the transmission. On 240

'Jeep*
UNIVERSAL
SERIES'
SERVICE
MANUAL

lightly
on the end of the
mainshaft
to
loosen
the

gear
and
separate
the two
units.

J-8.
Disassembly
—
T90,
T86AA
®
Refer to Fig. J-5, J-7
a. If the transfer
case
is
attached,
separate
it from
the
transmission
as
outlined
in Par. J-7. b.
Remove
the
shift
housing
and
gasket
from the
top of the
transmission
case.
The
shift
housing
can
be
disassembled,
if
necessary,
at
this
point
by re­
moving
the
shift
rails and forks from the
shift

housing.
Use care not to
lose
the
poppet
balls
and
springs.

Note;
On
CJ-5
A
and
C
J-6A
models
equipped
with
side-shift
remote-control
transmission
it is
neces­

sary to
remove
the main drive
gear
before
the
shift

forks can be
removed.

e.
Remove
the
three
screws
and
washers
attaching
the
front
main drive
gear
bearing
retainer to the
transmission.
Remove
the retainer and
gasket,

d.
Remove
the two
socket-head
screws
from the
front
end of the
transmission
case.
These
screws

support
the oil
collector
inside
the
case.

Note:
The oil
collector
has
been
discontinued
in

late
production
transmission
assemblies.
11881

FIG.
J-6—MAIN
SHAFT
RETAINING
PLATE

13321

FIG.
J-7—T86AA
THREE-SPEED
TRANSMISSION
—
CANE
SHIFT

1—
Bearing
Retainer Screws
2—
Main
Drive Gear Bearing Retainer
3—
Bearing
Retainer Oil Seal

,
4—Bearing Snap Ring
5—
Main
Drive Gear Snap Ring 6—
Main
Drive Gear Bearing 7—
Front
Bearing Oil Retaining Washer
8—
Main
Drive Gear
9— Pilot Roller Bearing
10— Shift
Rail
Cap
11—
Poppet
Ball

12—
Poppet
Spring
13—
Lock
Washer
14— Shift Housing Bolt
15—
Control
Housing 16— Interlock Plunger
17— Shift Lever Spring
18— Shift Tower Gasket
19— Blocking Ring 20—
Clutch
Hub Snap Ring
21— Synchronizer Spring
22— Synchronizer Plate
23—
Clutch
Hub
24—
Clutch
Sleeve

25— High and Intermediate Clutch
Fork

26— Shift
Fork
Pin
27— High and Intermediate Shift
Rail

28— Second Speed Gear 29—
Main
Shaft
30—
Low
and Reverse Sliding Gear
31—
Low
and Reverse Shift
Fork

32—
Low
and Reverse Shift
Rail
33—
Bearing
Spacer
34—
—Rear
Bearing Adapter
35—Rear
Bearing 36—
Rear
Bearing Snap Ring
37— Nut
38—Washer 39—
Transfer
Case Drive Gear
40—Lock
Plate
41 —Countershaft
42—
Rear
Countershaft Thrust Washer
(steel)

43—
Rear
Countershaft Thrust Washer (bronze)
44— Countershaft Bearing Washer
45— Countershaft Bearing 46— Countershaft Center Bearing Spacer
47— Reverse Idler Gear Shaft
48— Reverse Idler Gear Bearing Washer
49— Reverse Idler Gear Roller Bearings 50— Reverse Idler Gear
51— Countershaft Gear 52— Countershaft Front Thrust Washer
53— Plug 54— Shift Lever
55—
Transmission
Case
56— Retainer Gasket 245

J

THREE-SPEED
TRANSMISSION

FIG.
J-8—SHAFT
LOCK
PLATE
e. Tap lightly on the front end of the countershaft
to loosen the lock plate. Remove the lock plate
from
slots cut in the
rear
ends of the countershaft

and
reverse idler shaft. Refer to Fig. J-8.
f. Using special tool No. W-166 or a brass drift,
drive
the countershaft toward the
rear
of the case

and
remove it. The countershaft gear set
will
drop
to the bottom of the transmission case. If the

special
tool is used, the needle bearing rollers
will
remain
in the countershaft gear hub and the gears

and
bearings may later be removed as an assembly.
g. Remove the mainshaft
rear
bearing adapter.
h.
Remove the mainshaft and gears from the case.

The
mainshaft assembly with the gears
still
in place

may
be removed through the
rear
bearing adapter
opening. Do not
lose
pilot roller bearing when

separating
shafts.

i.
On
early production transmissions drive the main

drive
gear into the case enough to remove the oil
collector. Remove the oil collector from the trans­
mission case.

j.
Remove the main drive gear,
k.
Remove the countershaft gear set and the three

thrust
washers. Remove the washers, needle bear­
ing rollers, and spacer from the assembly. 1, Remove the reverse idler shaft and gear by

driving
the shaft into the case using a brass drift,

m.
This
completes the disassembly of the trans­
mission on
those
models with a cane shift,
n.
On
CJ-5
A
and
CJ-6 A
models equipped with a
remote shift transmission, inspect the poppet and

interlock
assembly which floats between the shift
lever assemblies described in Par. J-9.
FIG.
J-9—COUNTERSHAFT GEAR BEARING ARBOR
FIG.
J-l0—COUNTERSHAFT BEARING SPACERS J-9-
Transmission Interlocking Sleeve

I
inspection

a.
The interlock
sleeve
and poppet assembly should be carefully checked. Should the assembly
be too long, it
will
be impossible to shift gears and

if
it is too short, it
will
fail
to function as an inter­

lock
to prevent shifting into two gears at one time.

Locate
the intermediate-and-high control arm for
second gear position. Use a feeler
gauge
to measure
the clearance between the ends of the interlock

sleeve
and the notched surface of each shift lever
as shown in Fig.
J-l
1.

Clearance
must be from .001" to .007" [0,025 a
0,178 mm.] on each side of the interlock sleeve.

To
obtain correct clearance, interlock
sleeves
are

available
for selective fit.

The
different lengths can be identified by a letter at the end.

1.287"
[3,269 cm.] — etched C

1.291"
[3,279 cm.] — etched B
1.295"
[3,289 cm.] — etched A

1.299"
[3,299 cm.] — no
mark

1.303"
[3,309 cm.] — etched D

Should
an interlock
sleeve
need replacing, proceed
as follows:

Where
necessary drive out the taper retaining pins

from
the bottom of the shift lever bosses. Remove
the nuts, lock washers, and flat washers from the

4
FIG.
J-l 1—INTERLOCK
SLEEVE
CLEARANCE

246

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

J
flat washer, lock washer and nut.

q.
Check
the
complete
transmission for operation.

r.
Install
transmission case cover.

J-15.
T14A
TRANSMISSION
The
T14A is a three
speed
fully synchronized (all

forward
gears) transmission with helical drive gears
throughout.

The
main drive gear is supported by a
ball
bearing at the front end of the transmission case and is
piloted at its front end in an oil impregnated bush­
ing mounted in the crankshaft.

The
front end of the mainshaft is piloted in a row
of
roller
bearings set
into
the hollow end of the main

drive
gear and the
rear
end is
carried
by a
ball

bearing
mounted in the
rear
transmission case.
The
counter gear is
carried
on a single row of

rollers
at both ends. The reverse idler gear is
carried

on a single row of rollers in the center.
Thrust
is

taken
on thrust washers located
between
the
ends

of the counter and reverse idler gear and the thrust
bosses
in the case.

The
three forward gears (low, second, third) are

fully
synchronized. The synchronizer assemblies
consist of
clutch
hubs, clutch
sleeves,
clutch springs,

and
three synchronizer plates and are retained on
the mainshaft by a
select
fit snap
ring.
The
shift is manual through a cane shift lever and
interlock
assembly to the
rearward
shift fork
operating low and reverse gear and to the forward
shift fork operating second and
third
gear.
J-16.
TRANSMISSION
DISASSEMBLY
—
T14A

Refer
to Fig. J-13.

a.
If the transfer case is attached, separate it from
the transmission by removing the five capscrews
and
lockwashers.

b.
Remove cane shift housing cover and gasket

from
top of transmission case. The shift housing
cover can be disassembled if necessary, at this
point, by removing the shift
rails,
poppet
balls,

springs,
and shift forks. Refer to Fig. J-14.

c.
Remove nut and flat washer securing transfer case drive gear on the mainshaft. Remove transfer case drive gear, adapter, and spacer. Refer to

Fig.
J-15.
FIG.
J-15—TRANSFER
CASE
DRIVE

GEAR
ASSEMBLY
1—
Bearing
Adapter

2—
Bearing
Spacer

3—
Transfer
Case
Drive
Gear
4—
Flat
Washer 5— Nut
12885

FIG.
J-16—REMOVING
MAIN
DRIVE
GEAR
BEARING
1—W-329 Puller

d.
Remove main drive gear bearing retainer and
gasket. e. Remove main drive gear and mainshaft bearing snap rings.
f. Remove the main drive gear and mainshaft
bearings using bearing puller set W-329. Refer to

Figs.
J-16 and J-l7.
FIG.
J-17—REMOVING
MAINSHAFT
BEARING

1—W-329
Puller g. Remove main drive gear from transmission case.

h.
Remove mainshaft and gears as an assembly,
through the case cover opening as shown in Fig.

J-18.

i.
Remove the lockplate by tapping lightly on the
front end of the countershaft and reverse idler
shaft. Remove lockplate from
slots
in shafts. Refer
to
Fig.
J-19.

j.
Using Tool W-335, drive the countershaft
rear­

ward,
out of the case, as shown in Fig. J-20. The countershaft gear assembly
will
drop to the
bottom

of the case. Using Tool W-335
will
ensure that the

roller
bearings
will
remain in the countershaft gear
hub and may be removed as an assembly. 251

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

Jl
necessity for assembly, one should be made at this
time to assist on disassembly. One can be made by
using a \Y%N [2,86 cm.] diameter steel rod cut to

9.850*
{25,02
cm.] long.
Break
sharp
edges
with a
mill
file.) Keep the dummy shaft in contact with
the countershaft at all times to prevent dropping
the bearing rollers or thrust washers,

z.
With
the dummy shaft in position, place the
transmission
case on its side and carefully
roll
the countershaft gear cluster out of the case,

aa.
Complete the disassembly by removing the dummy shaft, thrust washers, four
sets
of bearing
rollers,
and spacers.

bb.
To disassemble the reverse idler gear assembly,
remove one of the snap rings and tap out the

washers,
both
sets
of bearing rollers, center spacer,
and
sleeve.
Remove the remaining snap
ring.

J1-4.
4-Speed
Transmission
Control
Housing
Disassembly

•
Refer to Fig. Jl-5.

The
gearshift lever, spring, and spring seat were previously removed for removal of the transmission

from
the vehicle.

a.
Remove the lock pins from the gearshift forks

and
gearshift rod ends. Remove the expansion plugs
from
the front and
rear
of the gearshift lever base. Remove back-up light switch.

b.
Remove the center (third and high) gearshift

rod
first. Drive this gearshift rod out the
rear

of the gearshift lever base. As the gearshift rod is
withdrawn
from the center section of the gearshift base, remove the interlock pin from the cross­
over
hole
in the gearshift rod. Before the gearshift
rod
is removed from the center section of the gear­
shift base, place a finger over the
hole
to prevent

loss
of the
ball
and spring.
Then
remove the rod.

c»
Remove the low- and second-speed gearshift rod
in
the same manner.

d.
Remove the gearshift rod lock balls and springs

and.
with a piece of
wire,
push the two gearshift rod
interlock
plungers out of the pockets in the center
section of the gearshift base.

In
the reverse gearshift rod end is a spring-loaded
plunger which prevents the
driver
from accidentally
shifting into reverse gear. Should this part require
servicing,
proceed as follows:
Remove the cotter key from the rod end assembly

and
at the same time hold a finger over the
hole

to prevent
loss
of the spring.
Then
shake out the
spring
and
ball.
Compress the plunger and spring

until
the C-washer
groove
just clears the end of
the casting. Remove the C-washer.

J1-5.
4-speed
Transmission Reassembly •
Refer to Fig. Jl-1.
Assemble the unit in the reverse order of dis­
assembly noting the following points:

a.
Assemble the countershaft assembly with the
fabricated
dummy shaft. The bronze front thrust

washer
and the steel backed bronze
rear
thrust
washer
should be coated with stiff lubricant and
installed
with the lugs
engaged
in the notches

in
the end of the gear cluster. Place the assembly
in
the transmission case and install the counter­
shaft from the
rear,
keeping the countershaft and
dummy shaft in contact to prevent dropping

bearing
rollers or washers. Tap the countershaft
lightly into position in the front of the case but
do not seat it until the reverse idler gear assembly

and
shaft have been installed in the case.

b.
Install
the reverse idler gear shaft in the case

until
the lock plate slot is adjacent to the slot in
the countershaft. Insert the lock plate in the
slots

of the shafts making sure the plate ends are square

with
the slots.
Install
the lock plate screw and
lockwasher
to act as a pilot while tapping the
shafts alternately into position in the case. Tighten
the lock plate screw securely.

c.
Begin assembly of the second speed synchronizer assembly (see
Fig.
Jl-6) by installing the low-and
-

second-speed clutch hub in the low-and-second-
speed gear.
Install
the retaining ring in the speed gear.
Install
the retaining ring in the low and
FIG.
Jl
-6—ASSEMBLING
SECOND-SPEED

SYNCHRONIZER
1—
Low
and Second
Clutch
Gear

2—
Ball

3—
Low
and Second
Clutch
Hub
4—
Shifting
Plate
second speed gear. Slide the hub out of the gear

in
the direction
opposite
the shift fork
groove

until
the
holes
in the hub are clear of the gear.
Install
the shifter plates and springs. Push the
hub back into the gear until the springs touch the

internal
teeth
of the gear. Push one of the shifter
plates toward the center of the gear while installing

ball.
See
Fig.
Jl-6 .
This
will
hold the
ball
in position.
Install
the other two balls in the same manner.

Be
careful when rotating the assembly to prevent the hub from slipping out of the gear. When the

balls
are installed, push the hub into the gear

until
the balls snap into the neutral position.

d.
Assemble the
direct
-
and
-
third
synchronizer as­
sembly in accordance with the instructions given

in
Section J, Par.
J-lle.

e.
Start
assembly of the mainshaft assembly by 263

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

K
the
bottom.
Remove
rear
bearing
cone
and roller
assembly from the shaft by striking the end of the
shaft lightly against a
wooden
block,
j.
Remove the set screw in sliding gear shift fork.
Remove shift rod.
See the following paragraphs for disassembly of
the front and
rear
bearing caps.

K-4.
Front
Bearing Cap Disassembly
•
Refer to Fig. K-1, K-2.

The
front bearing cap is a separate assembly which

may
be removed for service. Should difficulty be
experienced in this section of the transfer case,

follow
the
sequence
below
for removal and dis­ assembly.

a.
Remove the output shaft yoke as outlined in

Par. K-3.
Remove the
poppet
balls and
move
the
front wheel drive shift rod forward as outlined in

Par.
K-3f.

b.
Remove yoke oil seal with Tool W-251, as shown in Fig.
K-7.
Remove shift rod oil seals with

Tool
W-176, as shown in Fig. K-8.

c.
Remove the front bearing cap assembly as outlined in Par. K-3g.
FIG.
K-9—SHIFT
ROD OIL
SEAL INSTALLER

1—
Driver

2—
Thimble

3— Oil
Seal
d.
Remove the set screw from shifting fork and
shifting rod. The clutch gear and shifting fork can
be removed
together.

e. Remove output clutch shaft assembly by care­

fully
pressing it
thru
the bearing.
f. Remove bearing retainer snap ring and the

bearing.

K-5.
Rear
Cap Disassembly
•
Refer to Fig. K-1, K-2.

The
rear
bearing cap is partially disassembled
during
the dismantling of the transfer case. The
cap is, however, a separate assembly which may be
removed for service. Follow the
sequence
below
for removal and disassembly,
a.
Remove the output shaft
rear
end yoke or
companion
flange
as outlined in
Par. K-3 a.
Separate 271

K

TRANSFER
CASE
the brake drum and companion
flange
by remov­
ing bolts, lockwashers, and nuts.

b.
Remove the oil seal with Tool W-251, as shown

in
Fig. K-7.

c.
Remove
speedometer
driven gear assembly.

d.
Remove the cap screws attaching the cap and
brake
backing plate to the case.
Take
precautions
not to
lose
or damage bearing adjusting shims placed
between
the cap and the transfer case
housing.
e. Separate the
rear
cap and brake backing plate
assembly. See Section P for brake service pro­
cedures.
f. Remove
speedometer
driving gear.

K-6.
Transfer
Case
Reassembly
•
Refer to Fig. K-1, K-2.

Reassembly
of the transfer case is reversal of the

foregoing
procedure of disassembly. The output shaft snap ring may
best
be installed with Tool
FIG.
K-11—OUTPUT
SHAFT
SNAP

RING
INSTALLER
1—
Snap
Ring

2—
Snap
Ring
Installer Tool W-131
FIG.
K-12—OUTPUT
SHAFT
OIL
SEAL
DRIVER

1—
Driver
Tool W-143

2—
Seal
W-131,
output shaft snap ring installing thimble

and
driver,
shown in
Fig.
K-ll.
Use a
piece
of tub­
ing for installing the bearing
cone
and roller as­ semblies on the output shaft to prevent damage
to the assemblies.

Early
production transfer cases were equipped with
a
lVs" [2,86 cm.] diameter intermediate shaft

and
caged
needle
bearings. When installing the intermediate gear in early production transfer cases,

insert
the bearings in the gear, support the front

thrust
washer with Pilot Pin Tool W-192,
Fig.
K-10,
position the gears and
rear
thrust washer, and
insert
the shaft from the
rear
of the case.

Late
production transfer cases were equipped with
a
1
Vi"
[3,18 cm.] diameter intermediate shaft,

and
bearings consisting of individual rollers and
spacers.
A dummy shaft is required to install the
intermediate shaft. The dummy shaft should be slightly smaller in diameter than the intermediate
shaft and a little shorter than the width of the
intermediate gear. To install the intermediate gear,

first
load the bearing rollers and spacers in the gear using the dummy shaft.
Then
supporting the
front thrust washer with the fingers, position the gears and
rear
thrust washer and insert the shaft

from
the
rear
of the case, driving out the dummy
shaft.

Should
it be necessary to replace the
speedometer

driven
pinion bushing installation may be
best

made with bushing installer Tool W-133, shown
in
Fig. K-13. When the
rear
bearing cap assembly
is installed, check the end
movement
of the main-
shaft which determines the adjustment of the
tapered roller bearings. For correct bearing adjust-
|
11S4S

FIG.
K-13—SPEEDOMETER
PINION
BUSHING
DRIVER
1—Tool W-133
272