1953 JEEP CJ wheel

'Jeep'
UNIVERSAL SERIES
SERVICE
MANUAL

Dl

DAUNTLESS
V-6
ENGINE
Contents

SUBJECT
PAR.
SUBJEC

GENERAL
.... . . Dl-1 Oil Pump Cl(
ENGINE DESCRIPTION
D1-2

Engine
Mounts Dl-3

ENGINE REMOVAL
Dl-4
ENGINE DISASSEMBLY
Dl-5
Alternator
and Fan Belt Dl-11
Camshaft
.... Dl-26
Cooling Fan and Water Pump.
......
.Dl-12
Crankshaft
Front Oil Seal .Dl-21

Crankshaft
Pulley D1-17
Crankshaft
Vibration Damper Dl-18

Cylinder
Head Assembly Dl-24

Distributor
Dl-9
Exhaust
Manifold .Dl-8

Flywheel
Dl-28

Flywheel
Housing and
Clutch
Dl-27
Fuel
Pump. ... . .Dl-10
Intake
Manifold and
Carburetor
Assembly.
.............
.Dl-7

Main
Bearing and Crankshaft. Dl-32 Mounting Engine on Engine Stand. . . . .Dl-6

Oil
Dipstick. Dl-16
Oil
Filter
Dl-13
Oil
Pan.. ...
.......
.Dl-29
Oil
Pressure Sending Unit Dl-15

Oil
Pump Dl-19
Oil
Pump Intake Pipe and Screen Dl-30
Piston and Rod Assembly. Dl-31
Push
Rod and Valve
Lifter.
.Dl-25
Rocker
Arm Cover Dl-23
Starter
Motor Dl-14

Timing
Chain
and Sprocket Dl-22
Timing
Chain
Cover Dl-20

ENGINE CLEANING, INSPECTION AND REPAIR
. . ... .Dl-33
Camshaft
Cleaning and Inspection Dl-55
Connecting Rod Bearing Inspection
and
Fitting .Dl-49

Crankshaft
Cleaning Dl-38
Crankshaft
Inspection and Repair Dl-39
Crankshaft
Main Bearing Cleaning
and
Inspection Dl-41

Crankshaft
Main Bearings. Dl-40

Crankshaft
Pulley Inspection. Dl-70
Crankshaft
Vibration Damper Inspection. D1-69

Cylinder
Block .Dl-34
Cylinder
Block Cleaning Dl-35
Cylinder
Block Inspection Dl-36

Cylinder
Block Repair. .Dl-37
Cylinder
Head and Valve Repair .Dl-63

Cylinder
Head and Valve Cleaning
and
Inspection.. . .Dl-62

Flywheel
Cleaning and Inspection Dl-52

Flywheel
Housing Cleaning
and
Inspection Dl-54

Hydraulic
Valve
Lifter
Leakdown Test. .Dl-57
Main
Bearing Fitting or

Shim
Stock Dl-42, Dl-43

Oil
Pan Cleaning and Inspection .Dl-51
PAR.
and
Inspection. .... .Dl-68

Oil
Pump Intake and Screen Cleaning. . .Dl-50
Piston and Rod Assembly.
...........
.Dl-48
Piston and Rod Cleaning and Inspection.D1-45
Piston and Rod Disassembly Dl-44
Piston Fitting Dl-46
Piston Ring Fitting. .Dl-47

Ring
Gear
Replacement. .Dl-53
Rocker
Arm Assembly. Dl-60
Rocker
Arm Cleaning and Inspection. . .Dl-59

Rocker
Arm Cover Cleaning

and
Inspection D1-65

Rocker
Arm Disassembly .Dl-58
Timing
Chain
and Sprocket Inspection. . .Dl-66

Timing
Chain
Cover Cleaning

and
Inspection.. . Dl-67

Valve
Installation D1-64
Valve
Lifter
and Push Rod

Cleaning
and Inspection. . Dl-56

Valve
Removal Dl-61

ENGINE REASSEMBLY
Dl-71
Alternator
and Fan Belt Dl-96

Camshaft
Dl-80
Clutch
and Flywheel Housing Dl-79
Cooling Fan.. . .Dl-95
Crankshaft
End Play Check. . Dl-74

Crankshaft
Front Oil Seal Dl-85
Crankshaft
Pulley Dl-89
Crankshaft
Vibration Damper Dl-88
Cylinder
Block and Crankshaft
Rear
Oil Seals Dl-72

Cylinder
Head Assembly .Dl-82

Distributor
Dl-99

Exhaust
Manifold Dl-98
Flywheel
.Dl-78
Fuel
Pump.. .. . Dl-97
Intake
Manifold and Carburetor Assembly Dl-101

Main
Bearing and
Crankshaft
Installation
.
Dl-73

Oil
Filter
Dl-93
Oil
Level
Dipstick Dl-90

Oil
Pan Dl-77
Oil
Pressure Sending Unit Dl-91

Oil
Pump.. .Dl-87
Oil
Pump Intake and Screen Assembly. .Dl-76
Piston and Rod Installation Dl-75

Rocker
Arm Cover. Dl-83

Spark
Plugs.. Dl-100
Starter
Motor Dl-92
Timing
Chain
and Sprocket.
..........
.Dl-84

Timing
Chain
Cover Dl-86
Valve
Lifter
and Push Rod Dl-81

Water
Pump. Dl-94

ENGINE INSTALLATION
Dl-102

FINAL
IN-VEHICLE
ADJUSTMENTS.
D1-103

SERVICE
DIAGNOSIS
Dl-104
ENGINE SPECIFICATIONS
. .Dl-105 75

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

Dl

©©©©©©©©©

12697

FIG.
Dl-1—DAUNTLESS
V-6
ENGINE, SIDE SECTIONAL VIEW

1—
Fan
Blade
2—
Fan
Spacer

3—Fan
Pulley
4—
Water
Pump 5—
Timing
Chain
Cover
6—
Camshaft
Sprocket
7—
Thermostat
Bypass Hose
8—
Thermostat
Housing
9—
Thermostat

10—
Carburetor

11—
Intake
Manifold
12—
Rocker
Arm Cover 13—
Cylinder
Block 14—
Push
Rod
15—
Camshaft

16—
Flywheel
17—
Clutch
Pressure Plate
18—
Clutch
Driven Plate
19—
Clutch
Pilot Bearing
20—
Oil
Seal Packing
21—
Rear
Main
Bearing Shell
22— Connecting Rods
23—
Rear
Center
Main
Bearing Shell
24—
Oil
Screen
25—
Oil
Screen Pipe and Housing
26—
Oil
Pan 27—
Front
Center
Main
Bearing Shell
28—
Crankshaft

29—
Front
Main
Bearing Shell
30—
Timing
Chain

31—
Crankshaft
Sprocket
32—
Oil
Slinger
33—
Oil
Shedder 34 Oil Shedder Packing
35—
-Woodruff
Key
36—
"Vibration
Damper
37—
Crankshaft
Pulley
38—
Fan
Belt matic adjuster, to prevent lash in the valve operat­
ing linkage. Hydraulic valve lifters also provide

a
cushion of oil to absorb operating shocks. As shown in Fig. Dl-3, all parts of a hydraulic lifter

are
housed in the body, which is the cam follower.

At
the beginning of valve operation, the valve lifter body rests on the camshaft base circle.

Plunger
spring tension prevents lash clearances in the valve linkage.

As
the camshaft forces the valve lifter body up­

ward,
both oil in the lower chamber and check

ball
spring
tension firmly seat the check ball against the plunger to prevent appreciable
loss
of oil from
the lower chamber. Oil pressure forces the plunger
upward,
with the body, to operate the valve linkage.

As
the camshaft rotates to closed-valve position, the valve spring forces the linkage and lifter down­

ward.
When the
engine
valve seats, the linkage

parts
and plunger stop, but the plunger spring forces
the body downward .002" to .003"
[0,050
a
0,076
mm.] until it again rests on the camshaft base

circle.
Oil pressure then forces the check ball away

from
its seat and allows passage of oil past the check ball into the lower chamber.
This
replaces
the slight amount of oil lost by leakage. During
the valve opening and closing operation, a very
slight amount of oil escapes
between
plunger and body, and returns to the crankcase.
This
slight
loss
of oil (leak-down) is beneficial. It provides a
gradual
change of oil in the valve lifter; fresh oil
enters the lower chamber at the end of each cycle
of operation. 77

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

Dl

12710

FIG.
D1
-3—HYDRAULIC VALVE
LIFTER
ASSEMBLY, CROSS-SECTIONAL VIEW
1—
Snap
Ring
6—Ball Retainer

2— Rod
Seat
7—Plunger Spring

3—
Oil
Inlets
8—Lifter
Body

4—
Plunger
9—Bronzed
Cap
5— Feed
Hole
sages
in the block and cylinder head.

The
water cooled system is pressurized to provide efficient
engine
cooling. It consists of a centrifugal-
type water pump, mounted on the timing chain cover, and is driven by the
engine
fan pulley. The
pump provides coolant flow equally to both
cylin­
der banks under control of a thermostat. Coolant
flow is around the cylinders and through the
cylinder
head to dispel the heat of combustion in
the engine.

Dl-3.
Engine Mounts

The
engine-transmission unit is mounted to the chassis at three points by rubber pads. The two
front mounts are bolted to the
engine
cylinder
block and the frame members. These mounts sup­ port most of the
engine
weight, and absorb
vibra­

tion which would otherwise be caused by changes
in
engine
output torque. The single
rear
mount is
placed
between
the transmission and the trans­ mission support. It supports part of the engine'

and
transmission weight, and locates the
rear
of
the
engine
with respect to the centerline of the
vehicle.

Dl-4. ENGINE REMOVAL
To
remove the
engine
from the vehicle follow the
procedurers listed below:

a.
Remove hood. b. Disconnect battery cables from battery and
engine. c. Remove air cleaner.

d.
Drain
coolant from radiator and engine.
e.
Drain
engine
oil.
f. Disconnect alternator wiring harness from con­ nector at regulator.

cj.
Disconnect the fuel evaporative purge line con­ nected to the
P.C.V.
valve.

h.
Disconnect upper and lower radiator
hoses
from
the engine.

i.
Remove right and left radiator support
bars,

j.
Remove radiator from the vehicle.

k.
Disconnect
engine
wiring harnesses from con­
nectors located on
engine
firewall.
I.
On
engines
equipped with exhaust emission con­

trol,
remove the air pump, air distribution manifold,

and
anti-backfire (gulp) valve. See Section F2 for
procedure.

m.
Disconnect battery cable and wiring from en­

gine
starter assembly.

n.
Remove
engine
starter assembly from engine,

o.
Disconnect
engine
fuel
hoses
from fuel lines at

right
frame
rail,
p. Plug fuel lines.

q.
Disconnect choke cable from carburetor and cable support bracket mounted on engine,
r.
Disconnect exhaust pipes from right and left

engine
manifolds.
s. Place
jack
under transmission and support trans­
mission weight.
f. Remove
bolts
securing
engine
to front motor mounts.

u.
Attach suitable sling to
engine
lifting
eyes
and,
using hoist, support
engine
weight.
v. Remove
bolts
securing
engine
to flywheel housing.
w. Raise
engine
slightly and slide
engine
forward
to remove transmission main shaft from clutch plate spline.

Note:
Engine and transmission must be raised
slightly to release the main shaft from the clutch
plate while sliding the
engine
forward.
x. When
engine
is free of transmission shaft raise

engine
and remove from vehicle,
y. Place
engine
on suitable blocking or
engine
stand and remove sling from engine.

Dl-5.
ENGINE DISASSEMBLY

Engine
disassembly is presented in the sequence to be followed when the
engine
is to be completely
overhauled after removal from the vehicle. Some of the operations of the procedure are also appli­cable separately with the
engine
in the vehicle,
provided that wherever necessary the part of the
engine
to be worked on is first made accessible by removal of
engine
accessories or other parts.

When
the disassembly operations are performed
with
the
engine
out of the vehicle, it is assumed,
in
this procedure, that all of the accessories have
been removed
prior
to starting the disassembly and
the oil has been drained.

Dl

DAUNTLESS
V-6
ENGINE
In
addition to the instructions covering operations
for disassembling the
engine
out of the vehicle, special instructions are given to cover different
operations required when disassembly is
done
with
the
engine
installed.

During
disassembly operations, the
engine
should be mounted in a suitable
engine
repair stand.

Where
practicable, modify or adapt an existing re­

pair
stand as necessary to accommodate the
engine.
If
an
engine
repair stand is not used, take care to

perform
disassembly operations in a manner that
will
protect personnel against an accident and the
engine
and its parts against damage.

Dl-6.
Mounting Engine
On
Engine Stand

Refer
to Fig. Dl-4.
a.
With
the
engine
supported by a hoist, remove
the clutch housing and clutch. Match
mark
the flywheel and the clutch cover before disassembly to assure proper reassembly.
b. Position the
engine
on the
engine
stand.
c. Release
some
tension of the hoist cables and secure
engine
to stand.

d.
Make sure the position lock on the
engine
stand
is tight to prevent the
engine
from accidentally
inverting.

e.
Release the hoist cables.
FIG.
D1
-4—ENGINE
MOUNTED
ON
STAND

1—
Spacer
J-8690-6
A—Bolt,
i/2-NC
x 3i/2"

2—
Bolt,
3/a-NC
x 4*/2" 5—Adapter 21316-J 3—
Engine
Mounting Stand
Dl-7.
Remove Intake Manifold
and

Carburetor Assembly

Disconnect crankcase vent
hose,
distributor vacuum

hose,
and fuel line from carburetor. Disconnect two distributor leads from ignition coil. Disconnect

wiring
harness from coolant temperature sending

unit.
Remove ten cap
bolts
which attach intake
manifold to cylinder heads. Remove intake mani­
fold assembly and gaskets from
engine.

Dl-8. Remove Exhaust Manifold
The
engine
has two exhaust manifolds. Remove five attaching screws, one nut, and exhaust mani­
fold from each cylinder head.

Dl-9.
Remove Distributor

Disconnect vacuum
hose
and wiring harness from

distributor.
Disconnect spark plug cables from
spark
plugs. Remove sparks plugs from
engine.
Pull

spark
plug cable retainers from brackets on rocker

arm
covers. Remove mounting screw, retainer

bracket,
and distributor from timing chain cover.
If
timing chain and sprockets are not to be re­
moved from
engine,
note
position of distributor
rotor so that it can be installed in identical position.

Dl-10. Remove
Fuel Pump
Disconnect output fuel line from fuel pump. Re­
move
two mounting bolts, fuel pump, and gasket

from
timing chain cover.

Dl-11.
Remove Alternator
and Fan
Belt

Disconnect wiring harness from alternator. Remove nut and flat washer which fasten alternator to
adjustment bracket. Pivot alternator
inward,
to­

ward
engine
cylinder block, to relieve fan belt
tension. Remove fan belt from pulleys. Remove
two attaching screws, mounting bracket, and alter­ nator from right cylinder head of
engine.

Dl-12.
Remove Cooling
Fan and
Water Pump

Refer
to Fig. Dl-5.
Remove four cap screws, lock washers, cooling fan,

fan
hub, and fan drive pulley from flange of water
pump shaft. Remove nine attaching screws, water
pump, alternator adjustment bracket, and water pump from timing chain cover.

Dl-13.
Remove
Oil
Filter

Unscrew
oil filter from
engine
oil pump.

Dl-14.
Remove Starter Motor

Disconnect wiring harness from starter motor and
solenoid. Remove two attaching screws, starter motor, solenoid, and motor attaching bracket from

engine
flywheel housing and cylinder block.

Dl-15.
Remove
Oil
Pressure Sending Unit

Disconnect wiring harness from oil pressure send­
ing unit. Remove oil pressure sending unit from

engine
cylinder block.

Dl-16.
Remove
Oil
Dipstick

Withdraw
and remove oil level dipstick and dip­

stick
tube
from
engine
cylinder block.

Dl-17.
Remove Crankshaft Pulley

Remove six attaching screws and crankshaft pulley

from
crankshaft vibration damper. 80

Dl

DAUNTLESS
V-6
ENGINE
d.
Use two large screwdrivers to alternately pry
forward the camshaft sprocket and
then
the crank­
shaft sprocket, until the camshaft sprocket is pried
from the camshaft. Remove the camshaft sprocket, sprocket key, and timing chain from the
engine;

then
pry the crankshaft sprocket from the crank­shaft.
Dl-23.
Remove Rocker Arm Cover
Refer to Fig. Dl-8.
Remove
positive
crankcase ventilator valve from right rocker arm cover. Remove four screws which attach each rocker arm cover to cylinder head.
Remove each rocker arm cover and
gasket
from cylinder head. 14198

FIG.
Dl-6—ENGINE
CRANKCASE
PARTS

1— Connecting Rod Assy.
2— —Piston Pin

3—
Piston and Pin Assy.
4—
Ring
Set 5— Connecting Rod
Bolt
and Nut
6— Connecting Rod Bearing
7— Damper Spring
8— Damper
Bolt

9—
Timing
Chain Damper (Right)

10—
Cylinder
Block

11— Camshaft
12—
Woodruff
Key
13— Camshaft Bearing (No. 1 Front) 14— Camshaft Bearing (No. 2)
15— Camshaft Bearing (No. 3) 16—
Camshaft
Bearing (No. 4
Rear)
31-
17—
Camshaft
Plug
(Rear)
32-18—
Flywheel
33-
19—
Ring
Gear
34-
20— Crankshaft Bearing Set 35-
21—
Main
Bearing Oil Seal
(Rear)
36-
2 2—Crankshaft 3 7-
23—
Main
Bearing Packing Oil Seal
(Rear)
28-
24— Bearing Cap
Bolt
39-
25— Woodruff Key 40-
26—
Timing
Chain Damper
(Left)
41-
27— Damper Bolt 42- 28—
Timing
Chain
43-
29—
Camshaft
Sprocket 44-
30— Crankshaft Sprocket
—Crankshaft
Slinger

—Crankshaft
Shedder

—Crankshaft
Packing (Front)

—Timing
Gear
Cover Gasket

—Timing
Gear
Cover

—Vibration
Damper

-Bolt

-Washer

-Bolt

—Dowel Pin

-Camshaft
Thrust
Retainer and Bolt

—Washer

-Distributor
Drive
Gear

—Fuel
Pump Eccentric
82

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

Dl

14028
j

FIG.
D1-7—TIMING
CHAIN
AND
SPROCKET ALIGNMENT 1—
Camshaft Sprocket

2—
Crankshaft
3—Timing
Chain

Timing
Marks
Dl-24.
Remove
Cylinder
Head Assembly

a.
Unscrew, but do not remove, three
bolts
(Fig.

Dl-8)
which attach rocker
arm
assembly to cylinder
head.
Remove rocker arm assembly, with bolts,

from
cylinder head. See Section F2 for
engines

equipped with exhaust emission control.
b. Remove
eight
cylinder head bolts, cylinder head,

and
gasket from cylinder block.

Dl-25.
Remove Push Rod and Valve
Lifter

Refer
to Fig. Dl-8. Remove push rods and valve lifters from the
cylin­

der
block.
Mark,
or otherwise identify, each valve

lifter
according to its cylinder and valve position.

Note:
If valve lifters are not to be serviced, cover
valve lifters and camshaft with a clean cloth to
protect them from dirt

Dl-26.
Remove Camshaft

Refer
to Fig. Dl-6.

Carefully
withdraw camshaft forward from bear­
ing bores; avoid marring the bearing surfaces. Re­

move
camshaft from cylinder block.

Dl-27.
Remove Flywheel Housing and
Clutch

a.
If flywheel housing and clutch was not pre­
viously removed, remove six mounting
bolts
and
flywheel housing from cylinder block.
b.
Mark
clutch cover and flywheel to assure that
clutch
will
be installed in identical position when

engine
is assembled.
c. Remove six attaching screws and clutch assem­
bly from flywheel.
D1-28. Remove Flywheel

Refer
to Fig. Dl-6.
Remove six attaching
bolts
and flywheel from

engine
crankshaft.

Dl-29.
Remove Oil Pan

Refer
to Fig. Dl-5.

To
gain access to oil pan mounting bolts, invert
the
engine.
Remove mounting bolts, oil pan, and gasket from
engine
cylinder block.

Dl-30.
Remove Oil Pump Intake Pipe and Screen

Refer
to Fig. Dl-5.
Remove two attaching screws, and oil pump intake
pipe and screen assembly from
engine
cylinder block.

Dl-31.
Remove Piston and
Connecting
Rod Assembly

a.
Examine the cylinder bores. If bores are worn
so that shoulder or ridges exist at the top of piston

ring
travel, remove the ridges with a ridge reamer.
FIG.
Dl-8-

-CYLINDER HEAD,
AND COVER
ROCKER
ARM
1—
—Right
Rocker
Arm
Cover

2—
Rocker
Arm
Cover
Bolt

3—
Gasket

4—
Bolt
5—
Baffle
6—
Left
Rocker
Arm
Cover
7—
Rocker
Arm Shaft
8—Plug
9—
Rocker
Arm Spring
10—
Cylinder
Head
11—
Head
Gasket

12—
Push
Rod

13—
Valve
Lifter
14—
Intake
Valve

15—
Exhaust
Valve

16—
Dowel
Pin
17—
Valve
Spring 18—
Valve
Spring Cap
19—
Valve
Spring Cap Key

20—
Cotter
Pin
21—
Rocker
Arm Shaft End Washer

22—
Rocker
Arm Shaft Spring

23—
Rocker
Arm
24—
Rocker
Arm Shaft
Bracket

25—
Bolt
83

Dl

DAUNTLESS
V-6
ENGINE
This
will
prevent damage to piston rings or
crack­

ing piston lands during removal.
b. Use a silver pencil or quick-drying paint to mark
the cylinder number on all pistons, connecting rods,
and
caps. Starting at the front end of the crankcase,
the cylinders in the right bank are numbered 2-4-6
and
in the
left
bank are numbered
1-3-5.

c. Remove cap and lower connecting rod bearing

half
from No. 1 connecting rod.

d.
Push the piston and rod assembly away from
the crankshaft and remove it from top of cylinder bore. Then install cap and lower bearing half on
connecting rod.
e. Remove each connecting rod and piston as­ sembly as described in c and d, above.
FIG.
D1-9—CRANKSHAFT
MAIN
BEARING
CAPS

1—Thrust
Bearing
D1-32.
Remove
Main
Bearing and Crankshaft
a.
This
engine
has four crankshaft main bearings.

Front
to
rear,
they are numbered 1 to 4. Refer to

Fig.
Dl-9. With a silver pencil or quick-drying
paint, mark the bearing number on each main bearing cap.
b. Remove two
bolts
which secure first (front)

main
bearing cap to
engine
cylinder block. With

a
lifting bar, carefully pry the cap from the crank­ shaft and block. Be careful not to damage the cap,
block or crankshaft. Remove the bearing cap, with
lower main bearing half, from the cylinder block.

Keep
bearing half and cap
together.
Similarly, remove the next two main bearing caps with lower

main
bearing halves. To remove
rear
main bearing
cap,
use
rear
main bearing remover bolt W-323.
c. Remove the fabric seal from inside diameter of
fourth (rear) main bearing cap, and remove neo-
prene composition seal from outer surface of this
bearing cap. Discard both seals.

d.
Lift
and remove the crankshaft from
engine
cylinder
block. Do not remove upper main bearing
halves from block or lower main bearing halves

from
caps at this time. Mount main bearing caps

in
their original positions.
Dl-33.
ENGINE
CLEANING,
INSPECTION,

AND
REPAIR

The
cleaning, inspection, and repair procedures
detailed herein are recommended to be followed
when a
complete
engine
overhaul is to be made
with the
engine
out of the vehicle. These instruc­
tions
can generally be applied individually with the

engine
in the vehicle. Wherever the procedure dif­
fers due to the
engine
being in the vehicle, the necessary special instructions are provided. Inspec­
tion and repair instructions are included to cover
the cylinder block, cylinder head, crankshaft and bearings, connecting rods and bearings, oil pump,
valves and tappets, pistons and rings, flywheel,
timing gears, and the camshaft and bearings. In
addition, fitting operations for
these
engine
com­

ponents
are included.

D1-34.
Cylinder Block

The
cylinder block must be cleaned thoroughly, inspected, and repaired as necessary, as described
below.

Dl-35.
Cylinder Block Cleaning
Steam-clean the cylinder block, or clean it with

a
suitable cleaning solvent A scraper can be used
to remove
hard
deposits, but do not score machined
surfaces. Be certain that oil passages, valve cham­

bers,
crankcase, and cylinder walls are free from sludge, dirt, and carbon deposits. After cleaning,

dry
the cylinder block carefully with compressed
air.

Dl-36.
Cylinder Block Inspection

a.
Inspect cylinder walls visually for scoring,
roughness, or ridges which indicate excessive wear.
Check
cylinder bores for taper and out-of-round
with an accurate cylinder
gauge.
Measure eact bore at top, middle and bottom, both parallel tc
and
at right
angles
to the centerline of the
engine

The
diameter of the cylinder bores at any poin
FIG.
Dl-10—MEASURING
CYLINDER
BORE

1—Telescope Gauge [90*
From
Piston Pin]
84

DAUNTLESS
V-6
ENGINE

Note:
The rib on
edge
of cap and the conical
boss

on web of connecting rod must be toward
rear
of
engine
in all connecting rod assemblies of left
cyl­

inder
bank and toward front of
engine
in all con­necting rod assemblies of right cylinder bank.

Dl-50.
Oil
Pump Intake
and
Screen Cleaning

a.
Pry screen from housing and examine for clog­
ging due to deposit of sludge or other foreign

material.

b.
Clean
the screen and housing thoroughly in sol­
vent; dry with compressed air.

c.
Install
screen in housing.

Dl-51.
Oil Pan Cleaning and Inspection

Inspect
the oil pan for corrosion, dents, leaks, and
other damage. Inspect its mounting flange carefully
for damage or distortion to be certain that it
will
give
a
good
seal.

Dl-52.
Flywheel Cleaning
and
Inspection

Clean
the flywheel with suitable cleaning solvent;

dry
with compressed air. Inspect clutch face for

burned
or scuffed condition and for rivet grooves.
Inspection
for run out or improper mounting is de­

scribed
in installation procedure.
Inspect
teeth
of the flywheel
ring
gear for
burrs,

nicks,
and minor distortion. If necessary and pos­
sible, use a small emery wheel to remove
burrs
and
reshape teeth. If gear
teeth
are broken,
cracked,

seriously
burred
or deformed, the
ring
gear must be replaced.

Dl-53.
Ring Gear Replacement

a.
Drill
a
hole
between
two
ring
gear teeth; then

split
the gear with a cold chisel. Be careful not to
damage
ring
gear shoulder or seat surfaces of fly­
wheel.

b.
Polish several
spots
on the new
ring
gear to be

installed.
With
a hot plate or slowly moving torch,
heat the new
ring
gear until polished
spots
become

blue, about
600°F.
[312°C.].

Caution:
Do not heat the
ring
gear to a temperature
greater than
800°F.
[424°C.].
Excessive heat
will

destroy heat treatment given to
ring
gear during
manufacture.

c.
Quickly
install
ring
gear on flywheel. Chamfered

edge
of
ring
gear must be toward
ring
gear shoulder
of flywheel. Be certain that
ring
gear is seated prop­

erly.
Allow
ring
gear to cool slowly, so that it
will

be held tightly in place.

Dl-54.
Flywheel Housing Cleaning and Inspection

Both
flywheel and clutch are enclosed by a fly­
wheel housing. Its front surface is bolted to the
engine
cylinder block, and its
rear
surface acts as

front
support to the transmission.
Clean
the fly­ wheel housing with a suitable cleaning solvent; dry
with
compressed air. Inspect front and
rear
surfaces
for distortion and improper alignment with each
other;
these
planes must be
parallel
to assure
proper
alignment
between
engine
and transmission.
Dl-55.
Camshaft Cleaning
and
Inspection

Clean
both camshaft and camshaft bearing surfaces

with
a suitable cleaning solvent; dry with com­
pressed air.

Note:
The steel-backed babbitt-lined camshaft
bearings are pressed into the crankcase.
From
front
to
rear,
each bearing is .030" [0,76 mm.] smaller
in
diameter than the preceding bearing.
From
front
to
rear,
each camshaft
journal
is correspondingly
smaller
in diameter.

The
camshaft bearings must be line reamed to

proper
diameter after being pressed into crankcase.
Since
this operation requires special reaming equip­
ment, the original bearings should be retained un­
less
they are severly damaged. Slightly scored cam­
shaft bearings are satisfactory if the surfaces of camshaft journals are polished, bearings are
polished to remove
burrs,
and
radial
clearance

between
camshaft and bearings is within .0015"
to .004" [0,038 a 0,102 mm.].

Dl-56.
Valve Lifter
and
Push
Rod
Cleaning and Inspection
a.
Examine the cam contact surface at lower end of each valve lifter body. If surface is excessively

worn,
galled, or otherwise damaged, discard the
valve lifter. Also examine the mating camshaft
lobe
for excessive wear or damage.

b.
Disassemble one or two valve lifters, as de­

scribed
below, and inspect them for
dirt
or
varnish.
If
they are dirty or have a varnish deposit, clean

and
inspect all twelve valve lifters. Otherwise,
service
only
those
valve lifters which do not operate

properly.

c.
To disassemble each valve lifter, depress the
push
rod seat with a push rod, and remove the
plunger retainer from the valve lifter body with

a
retainer remover. Remove push rod seat and
plunger from valve lifter body. If plunger sticks
in
valve lifter body, place body in large end of

a
plunger remover tool, with plunger downward.
While
holding lifter with thumb, rap the open end
of remover against a block of wood with just enough force to jar the plunger from body. Refer to
Figs.
Dl-20, Dl-22 and Dl-23.

d.
Drain
oil from valve lifter and remove the check
valve retainer,
ball,
valve spring, and plunger
spring.

e. Keep all parts of each valve lifter separated

during
part cleaning and inspection. The valve

lifter
body and plunger are selectively fitted to each other and must not be interchanged with parts
of other valve lifters.
f. Rinse all valve lifter parts in kerosene to remove as much oil as possible.
This
will
reduce contamina­
tion of the cleaning solvent. Immerse all parts in cleaning solvent for approximately one hour. The
time required
will
depend on varnish
deposits
and
effectiveness
of the solvent. After the varnish has
dissolved or has
softened
sufficiently to permit re­

moval
by wiping, allow parts to
drain.
Varnish
can
then be cleaned from the valve lifter body
with
a
brush.
Rinse the parts in kerosene to dissolve 90