1953 JEEP CJ bolt pattern

'Jeep*
UNIVERSAL
SERIES SERVICE
MANUAL

D
straight
in the hole, then tap the dowel lightly

with
a hammer until it
bottoms.

d.
When installing bearing eaps, be sure to tighten
the
bolts
evenly in each cap to
pull
it into place
without bending the
dowels
or distorting the
bearing
cap.
e. Other parts of the block which require inspec­ tion
and
possible
repair,
but which are directly
related
to other
engine
components (such as tappets, pistons, camshaft, valves, crankshaft, and

oil
pump) are covered later in this section.

D-35.
Cylinder
Bores

The
cylinder bores may be reconditioned by honing
or
reboring. Use oil-soaked rags to protect
crank­

shaft
journals
and other
engine
parts from abrasive
dust during all reconditioning operations.

Both
honing and reboring of the cylinders must be
done
carefully to fit the pistons and to obtain
specified clearances. If reboring of the cylinder bores is not required but the walls are glazed, use

a
finishing
hone
to remove the glaze. Reboring the cylinders must not be attempted unless ade­
quate facilities and experienced service technicians
are
available. The amount of material to be re­moved is determined from the original diameter
of the cylinder bores (3.125" to 3.127") [79,375 a
79,426
mm.] plus the amount of oversize in diameter
of the oversize pistons to be fitted. Pistons are
available
in the following oversizes.
.010"
[0,254
mm.] .030" [0,762 mm.] .020" [0,508 mm.] .040" [1,016 mm.}

The
largest cylinder bore
will
determine the over­
size to which all cylinders must be rebored, since the size and weight of all pistons must be uniform
to maintain proper
engine
balance. The maximum rebore should not exceed .040" [1,016 mm.] from

standard.
Measure
the cylinder diameters by making mea­
surements both parallel to and at right angles to
crankshaft
over entire piston travel and at
bottom

of cylinder. Proceed as follows:

a.
If bores are scored; if out-of-round
exceeds
.005
"
[0,127 mm.]; if diameters differ more than .005";

or
if taper
exceeds
.005
"
on diameter, it is generally
recommended that cylinders be reconditioned by
reboring
and honing to the next oversize using new
pistons of the proper size.

Note:
If reboring is performed, allow .0015"
[0,0381
mm.] for final honing.

All
cylinder bore diameters must be within .002
"
[0,0508
mm.] after reconditioning.

b.
If bore measurements are within the above

limits,
but indicate hollows or waviness, cylinders should be honed with 250 grit
stone
hone. Pump
hone
up and down in cylinder while it is rotating
to produce a satin-finish, diamond cross-hatched

pattern
approximately 30° with horizontal. Hone
only enough to correct waviness.
c. If cylinder bore correction is unnecessary, break the glaze on cylinder walls with a 250 grit
stone

hone
or with a suitable deglazing tool. Operate the
hone
or deglazer to obtain diamond cross-hatched

pattern
previously mentioned.

d.
Regardless of type of correction on cylinder
walls,
wash out bores thoroughly afterwards and
apply
a light coat of
engine
oil. If cylinders have
been rebored or honed heavily, measure cylinder
diameters again to assure proper selection of piston
size.

D-36.
Pistons, Rings, and Connecting Rods
Pistons are each fitted with three rings, two com­ pression rings and one oil control
ring.
The pistons have an extra
groove
above the top ring which acts as a heat dam or insulating
groove
to protect
against sealing of the top ring in the ring
groove

with
hard
carbon. The piston pin is secured by the lock screw.

The
pistons and connecting rods were removed from
the
engine
as assemblies. If cylinders were rebored,
new oversized pistons and rings
will
have to be in­

stalled.

Disassemble the pistons and rods. Remove the
two compression rings, the oil control
ring,
and the oil control ring expander from each piston. Do not remove the
bolts
from the lower end of the
connecting rods unless the
bolts
are damaged.
Clamp
each connecting rod and piston assembly

in
a padded bench vise and remove the piston pin

lock
screw and lockwasher. Press the piston pin
out of the piston and connecting rod.
Clean
all
carbon,
gum, and lacquer
deposits
from both the

inner
and outer surfaces of each piston, connecting

rod,
and piston pin. Use a ring
groove
cleaner or a
broken
ring filed to a sharp square
edge
to clean
the carbon from the piston ring
grooves
and the

insulator
groove. Use care not to scrape metal from
the sides of the
grooves
or make
burrs
on ring
groove
surfaces. Run a length of wire through the

oil
spray
hole
near the lower end of the connecting

rod
to clear the
hole
of hardened oil
deposits
or
foreign matter.
Carefully
inspect the pistons and
replace
any that are broken or cracked. Replace
pistons if any of the ring lands are chipped, broken,
or
rounded on the
edges;
or if the piston is scored,

scratched,
or burned so seriously that the imperfec­
tions cannot be removed with a hand honing
stone

or
crocus cloth.

Replace
the pistons as follows:

a.
After cylinder bores have been carefully checked for out-of-round and taper (Par. D-35), check fit
of each piston to cylinder bore with block and
pistons clean and dry and at approximately 70
°F.
[21°C]
by using Piston Fitting Gauge And Scale

Tool
No. C-690 as shown in Fig. D-7. Use a .003"
[0,0762
mm.] thickness
gauge
%" [19 mm.] wide.

The
piston is fitted upside down in the block to
facilitate the operation. The
gauge
must extend the
full
length of the piston on the thrust side
(opposite

side from slot in piston
skirt).
Scale should register
5
to 10 pounds [2,3 a 4,5 kg.]
pull
to remove the
thickness
gauge
from
between
cylinder
wall
and piston. Excessive
pull
indicates need for a slightly

smaller
piston or additional honing of cylinder. In­ sufficient
pull
indicates need for fitting a larger piston. 47