2024 MAZDA CX90 torque

Do not start the engine or shake
the vehicle while it is jacked up.
Starting the engine or shaking the
vehicle while it is jacked up is
dangerous as it could cause the
vehicle to fall off the jack resulting
in an accident.
Never go under the vehicle while it
is jacked up.
Going under the vehicle while it is
jacked up is dangerous as it could
result in death or serious injury if
the vehicle were to fall off the jack.
8. Remove the lug nuts by turning them counterclockwise; then
remove the wheel and center cap.
Locking Lug Nuts
If your Mazda is equipped with the
optional antitheft wheel lug nuts, a
special key must be used to unlock the
locking lug nut for each wheel. The key
is stored in the glove compartment,
center console storage, storage box, or
trunk. Register the key and lug nuts
with the lock manufacturer by filling
out the registration card and mailing it
in using the accompanying envelope. If
the key is lost, consult an Authorized
Mazda Dealer or use the lock
manufacturer’s order form to order a
new key.
Antitheft wheel lug nuts cannot be
installed on a steel wheel spare tire.
When installing a temporary spare tire,
use one of the original lug nuts in place
of the locking lug nut. The original lug
nuts are stored inside your Mazda.
1. Antitheft lug nut
2. Special key
To remove an antitheft lug nut
1. Obtain the special key for the antitheft lug nut.
2. Place the special key on top of the antitheft lug nut, and be sure to
hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Do not
use a power impact wrench.
3. Place the lug wrench on top of the key and apply pressure. Turn the
wrench counterclockwise.
To install the antitheft lug nut
1. Place the special key on top of the nut, and be sure to hold the key
square to it. If you hold the key at
an angle, you may damage both key
and nut. Do not use a power
impact wrench.
2. Place the lug wrench on top of the special key, apply pressure, and
turn it clockwise.
Nut tightening torque
N·m (kgf·m, ft·lbf) 108―
147 (12 ―14,
80― 108)
What to Do in Case of Emergency
Tire is Punctured or Bursts
8-25
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Mounting the Spare Tire
1. Remove dirt and grime from themounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.

WARNING
Make sure the mounting surfaces
of the wheel, hub and lug nuts are
clean before changing or replacing
tires.
When changing or replacing a tire,
not removing dirt and grime from
the mounting surfaces of the wheel,
hub and hub bolts is dangerous.
The lug nuts could loosen while
driving and cause the tire to come
off, resulting in an accident.
2. Mount the spare tire.
3. Install the lug nuts with the beveled edge inward; tighten them by hand.

WARNING
Do not apply oil or grease to lug
nuts and bolts and do not tighten
the lug nuts beyond the
recommended tightening torque.
Applying oil or grease to lug nuts
and bolts is dangerous. The lug nuts
could loosen while driving and
cause the tire to come off, resulting
in an accident. In addition, lug nuts
and bolts could be damaged if
tightened more than necessary.
4. Turn the lug wrench
counterclockwise and lower the
vehicle.
5. Use the lug wrench to tighten the nuts in the order shown.

If you are unsure of how tight the
nuts should be, have them
inspected at an Authorized Mazda
Dealer.
Nut tightening torque
N·m (kgf·m, ft·lbf) 108
―147 (12 ―14,
80 ―108)
What to Do in Case of Emergency
Tire is Punctured or Bursts
8-26
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Standard tire
(U.S.A. and Canada)
Tire sizeInflation pressure
Front Rear
265/55R19 109V 250 kPa (2.5 bar, 36 psi)250 kPa (2.5 bar, 36 psi)
275/45R21 110W
*1250 kPa (2.5 bar, 36 psi) 270 kPa (2.7 bar, 39 psi)
Single occupant’s weight: About 75 kg*1 Before driving at high speeds, increase the pressure of the tires. For speeds above 175 km/h (109
mph), increase the pressure of the tires by 40 kPa (0.4 bar, 5.8 psi).
After high-speed driving, returning to standard tire pressure is recommended.
Temporary spare tire*
Tire size Inflation pressure
T155/90D18 113M 420 kPa (4.2 bar, 60 psi)

Lug nut tightening torque
When installing a tire, tighten the lug nut to the following torque.
108―147 N·m (12―14 kgf·m, 80―108 ft·lbf)
Specifications/Customer Information and Reporting Safety Defects
Ve h i c l e
Specification
10-72*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04