2024 MAZDA CX90 instrument cluster

Always close the door and windows
when refueling. If a fire occurs with
the doors or windows open, the
flames may spread into cabin.
 Do not spill fuel on the vehicle while
refueling. It may cause discoloration,
stains, or paint damage.
 Do not use any non-genuine
fuel-filler cap. Use of a non-genuine
fuel-filler cap may lead to a
malfunction in the fuel system or
emission system.
(U.S.A. and Canada)
It may also cause the check engine
light in the instrument cluster to
illuminate.
 When using an automatic car wash
or a high water pressure car wash,
make sure that the fuel lid is closed
and lock the doors. Otherwise, the
fuel lid may open unexpectedly and
become damaged.
 (U.S.A. and Canada)
If the check fuel cap warning light
illuminates, the fuel-filler cap may
not be properly installed. If the
warning light illuminates, park your
vehicle safely off the right-of-way,
remove the fuel-filler cap and
reinstall it correctly. After the cap has
been correctly installed, the fuel cap
warning light may continue to
illuminate until a number of driving
cycles have been completed. A drive
cycle consists of starting the engine
(after four or more hours with the
engine off) and driving the vehicle on
city and highway roads. Continuing
to drive with the check fuel cap
warning light illuminated could cause
the check engine light to illuminate
as well.Refueling
1. Close all the doors, windows, and
the liftgate.
2. Switch the vehicle power OFF.
3. Press the fuel-filler lid opener switch.
“Preparing for Refuelling” is
displayed in the instrument cluster.
4. Make sure that the indication in the instrument cluster changes to
“Ready to Refuel”.
5. Unlock the driver's door.
6. Press the fuel-filler lid.
The fuel-filler lid opens.
Driving
Refueling
5-105
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Charge indicator
The illumination/flash pattern of the
charge indicator can be checked using
the labels on the charge lid.
Charge indicator
illumination/flash pattern Content
— OFF Charging is possible.
(White) ON
Turns on when waiting for
starting to charge.
(White) Flashes
slowly The brightness changes
when the charging timer is
set.
(Green)
Flashes
slowly The brightness changes
during charging.
(Green)
ONTu r n s o n w h e n c h a rg i n g i s
completed.
Turns off after a certain pe-
riod of time has passed
since charging was com-
pleted.
(Amber)
FlashesFlashes when the charging
connector is connected and
the selector lever is in a po-
sition other than P.
Shift the selector lever to
the P position.
Charge indicator
illumination/
flash pattern Content
(Amber)
ONTurns on if there is a prob-
lem with the charging sys-
tem when the charging
connector is connected.
Wait a few minutes then re-
connect the charging con-
nector.
(Red)
ONTurns on if there is a prob-
lem with the charging sys-
tem and the charging port
lid is opened or the charg-
ing connector is connected.
Have your vehicle inspect-
ed by an Authorized Mazda
Dealer.
Charge status screen
When the driver's door is opened
while the charge connector is
connected, the charging status is
displayed in the instrument cluster.
1. Charge status icon
2. Message
3. Remaining power of the high
voltage battery (Displayed only
when vehicle power is switched
OFF)
4. Time to complete charging
5. EV maximum driving distance (Displayed only when vehicle
power is switched OFF)
Driving
Charging
5-117
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the High
Beam Control System (HBC)
NOTE
The distance in which the HBC can
detect objects varies depending on
the surrounding conditions.
The Forward Sensing Camera (FSC)
may not be able to detect target
objects correctly, and the HBC may
not operate normally.
Refer to Forward Sensing Camera
(FSC) on page 5-127.
Using the HBC
Make sure that the light switch is in the
AUTO position.
The HBC determines the surrounding
conditions and operates automatically.
When the HBC operates, the HBC
indicator light (green)
in the
instrument cluster turns on.
Switching the headlights to high
beams
The HBC switches the headlights to
high beams when all of the following
conditions are met.
The vehicle speed is about 30 km/h
(19 mph) or faster.
The system does not detect a vehicle
ahead.
Switching the headlights to low
beams
The HBC switches the headlights to
low beams when any of the following
conditions is met.
The vehicle speed is less than about
20 km/h (12 mph).
When driving in areas with a
continuous line of street lamps or on
roads in well-lit cities and towns.
The system detects the headlights of
a vehicle ahead.
Canceling the HBC during operation
When the HBC is canceled, the HBC
indicator light (green)
in the
instrument cluster turns off.
Press the HBC switch again to make
the HBC operable.
NOTE
If the vehicle power is switched OFF
with the HBC turned off, the HBC
automatically turns on the next time
the vehicle power is switched ON.
Driving
High Beam Control System (HBC)
5-142
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the LaneDeparture Warning System (LDWS)
LDWS operates
The LDWS operates when all of the
following conditions are met.
The vehicle speed is about 64 km/h
(40 mph)or faster.
The system detects white (yellow)
lane lines.
The CTS steering assist function is
not operating.
The system determines that the
vehicle may depart from the lane.
When the LDWS is operating, a screen
display and a warning sound (steering
wheel vibration and warning sound)
notify the driver of the danger.
Instrument cluster
Active driving display
NOTE
The LDWS operates only on the side
that detects white lines (yellow
lines).
The forward sensing camera (FSC)
may not be able to detect target
objects correctly, and the LDWS may
not operate normally.
Refer to Forward Sensing Camera
(FSC) on page 5-127.
The LDWS warning type can be
changed using Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
LDWS is temporarily canceled
If any of the following conditions is
met, the LDWS is canceled. In
addition, the LDWS is automatically
enabled when the condition changes
and the system is operable.
The turn signal lever is operated.The accelerator pedal is operated.The steering wheel is operated.The brake pedal is depressed.
Turning off the LDWS
There are 2 ways to turn off the LDWS.
Turn off the LDWS using Mazda
Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Turn off the LDWS using the
i-ACTIVSENSE OFF switch.
Refer to How to Use the
i-ACTIVSENSE OFF switch on page
5-126.
Driving
Lane Departure Warning System (LDWS)
5-145
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the Blind
Spot Monitoring (BSM)
When the BSM operates
The BSM operates when all of the
following conditions are met.
The vehicle speed is about 10 km/h
(6.2 mph) or faster.
The system detects an approaching
vehicle.
When the BSM operates, the driver is
notified of the presence of an
approaching vehicle using the BSM
warning lights and a screen display
(white)
*1.
BSM warning light
Instrument cluster
Active driving display
*1 The instrument cluster screen display (white)
is displayed only when the instrument
cluster is set to the i-ACTIVSENSE display.

When the turn signal lever is operated
in the direction in which an
approaching vehicle is detected, the
driver is notified of the danger by
flashing of the BSM warning lights, the
warning sound, and the warning
indication (amber).
BSM warning light
Instrument cluster
Driving
Blind Spot Monitoring (BSM)
5-147
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Active driving display
NOTE
The BSM may not operate normally if
any of the following conditions is
met.
The rear side radar sensors cannot
detect an object.
Refer to Radar Sensors on page
5-131.
The road is on a steep slope.The road is extremely wide.You make a lane change 2 lanes or
more.
The BSM may operate when turning
at intersections in urban areas or
with stationary objects on the road
or the roadside (such as guardrails,
sidewalls, and parked vehicles).
If a Mazda genuine trailer hitch is
used, the BSM is automatically
turned off when the trailer's
electrical connector is connected.
When pulling a trailer other than
with a Mazda genuine trailer hitch,
or while an accessory such as a
bicycle carrier is installed to the rear
of the vehicle, turn off the BSM.
Otherwise, the radar’s radio waves
will be blocked causing the BSM to
not operate normally.
The brightness of the BSM warning
lights is linked to the panel light
control.
Refer to Dashboard Illumination on
page 5-35.
When the Vehicle Exit Warning
operates*
The Vehicle Exit Warning operates
when all of the following conditions
are met.
The vehicle is stopped.Within 3 minutes after the vehicle
power is switched OFF or the vehicle
power is switched ON.
The system detects an approaching
vehicle.
When the Vehicle Exit Warning
operates, the driver is notified of the
presence of an approaching vehicle
using the warning lights and the
instrument cluster screen display
(white)
*1.
BSM warning light
Instrument cluster
*1 The instrument cluster screen display (white)
is displayed only when the instrument
cluster is set to the i-ACTIVSENSE display.
However, when the vehicle power is OFF,
Driving
Blind Spot Monitoring (BSM)
5-148*Some models.
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

the instrument cluster screen display (white)
is not displayed.

In addition, when the door in the
direction in which an approaching
vehicle is detected is opened, the
driver is notified of the danger by
flashing of the warning lights, the
warning sound, and the instrument
cluster warning indication (amber).
BSM warning light
Instrument cluster
NOTE
The Vehicle Exit Warning may not
operate normally if any of the
following conditions is met.
The rear side radar sensors cannot
detect an object.
Refer to Radar Sensors on page
5-131.
There is a parked vehicle near your
vehicle.
Moving objects are slow.The Vehicle Exit Warning is not
automatically turned off even if a
Mazda genuine trailer hitch is used.
If a trailer is towed or a bicycle
carrier is attached to the rear of the
vehicle, the radar signal may be
blocked and the Vehicle Exit Warning
may not operate correctly.
The Vehicle Exit Warning may
operate with stationary objects on
the road or the roadside (such as
guardrails, sidewalls, and parked
vehicles).
The brightness of the BSM warning
lights is linked to the panel light
control.
Refer to Dashboard Illumination on
page 5-35.
Tu r n i n g off the BSM and the Vehicle
Exit Warning
There are 2 ways to turn off the BSM
and the Vehicle Exit Warning.
Tu r n
off the BSM and the Vehicle Exit
Warning using Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Tu r n off the BSM and the Vehicle Exit
Warning using the i-ACTIVSENSE
OFF switch.
Refer to How to Use the
i-ACTIVSENSE OFF switch on page
5-126.
Driving
Blind Spot Monitoring (BSM)
5-149
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the Distance& Speed Alert (DSA)
Operating the DSA
The DSA operates when all of the
following conditions are met.
The vehicle speed is about 30 km/h
(19 mph) or faster.
The system determines that the
distance to the vehicle ahead is
close.
When the DSA operates, the screen
display notifies the driver that the
distance between your vehicle and a
vehicle ahead is close.
Instrument cluster
Active driving display
NOTE
The objects which operate the DSA
are four-wheeled vehicles. However,
the DSA may also operate in the
presence of motorcycles and
bicycles.
The DSA does not operate on
stopped vehicles.
When the speed of the vehicle ahead
is extremely slow, the DSA may not
operate normally.
Turning off the DSA
There are 2 ways to turn off the DSA.
Tu r n off the DSA using Mazda
Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Turn off the DSA using the
i-ACTIVSENSE OFF switch.
Refer to How to Use the
i-ACTIVSENSE OFF switch on page
5-126.
Driving
Distance & Speed Alert (DSA)
5-154
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04