2024 MAZDA CX90 tow

2. Attach the 2 hooks of the storage bag to each of the 2 luggage hooks on the right
side of the luggage compartment, and tightly secure the storage bag. At this
time, make sure that the logo on the storage bag is facing toward the center of
the luggage compartment.
CAUTION
Be careful when handling the storage bag because the hooks on the storage bag
have sharp areas. If your hands or fingers touch the sharp areas, your hands or
fingers could be injured.
NOTE
When the storage bag hooks and the luggage hooks hit against each other, they
make noise. If the noise distracts your attention while driving , wrap the included
sheet around the areas the hooks make contact.
Charge port
1. Charging indicator
2. Charge port
3. Charging port cap
4. Charging port lid
Driving
Charging
5-114
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Do not apply accessories, stickers, or
film to the windshield near the
Forward Sensing Camera (FSC). If the
area in front of the Forward Sensing
Camera (FSC) lens is obstructed, it
will cause the system to not operate
correctly even if it is transparent.
 Always keep the windshield glass
around the Forward Sensing Camera
(FSC) clean by removing dirt or
fogging. If the windshield is fogged,
press the windshield defroster
switch.
 The Forward Sensing Camera (FSC)
includes a function for detecting a
soiled windshield and informing the
driver, however, depending on the
conditions, it may not detect plastic
shopping bags, water or snow on the
windshield. In such cases, the system
cannot accurately determine a
vehicle or obstruction in front and
may not be able to operate normally.
Always drive carefully and pay
attention to the road ahead.
 When cleaning the windshield, do
not allow glass cleaners or similar
cleaning fluids to get on the Forward
Sensing Camera (FSC) lens. In
addition, do not touch the Forward
Sensing Camera (FSC) lens.
 Consult an Authorized Mazda Dealer
regarding cleaning the interior side of
the windshield around the Forward
Sensing Camera (FSC).
 If there are cracks or damage caused
by flying gravel or debris on the
windshield, always have the
windshield replaced. Consult an
Authorized Mazda Dealer before
replacing the windshield.
 Consult an Authorized Mazda Dealer
before doing repairs around the
Forward Sensing Camera (FSC).When doing repairs around the
rearview mirror, consult an
Authorized Mazda Dealer.
 Always use tires of the specified size
and the same manufacturer, brand,
and tread pattern on all 4 wheels. In
addition, do not use tires with
significantly different wear patterns
or tire pressures on the same vehicle
(including temporary spare tire).
NOTE
If the Forward Sensing Camera (FSC)
does not function normally due to
fog or the vehicle being driven
towards the sun, the functions
related to the Forward Sensing
Camera (FSC) are temporarily
stopped. In this case, the following
warning indications turn on.
However, this does not indicate a
problem.
HBC warning indicationi-ACTIVSENSE warning indicationSBS OFF indicationIf the Forward Sensing Camera (FSC)
does not function normally due to
high temperatures, the functions
related to the Forward Sensing
Camera (FSC) are temporarily
stopped. In this case, the following
warning indications turn on.
However, this does not indicate a
problem. Cool down the area
around the Forward Sensing Camera
(FSC) such as by turning on the air
conditioner.
HBC warning indicationi-ACTIVSENSE warning indicationSBS OFF indication
Driving
Forward Sensing Camera (FSC)
5-128
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

The target object is extremely
small.
The target object is extremely low/
high.
A vehicle approaches while
turning.
A vehicle that has stopped
suddenly starts to move.
Multiple objects move at the same
time.
The bumper around a front side
radar sensor is deformed.
Foreign matter is adhering to the
bumper around a front side radar
sensor.
The temperature near a front side
radar sensor is extremely hot.
The front side radar sensors may not
detect the following target objects.
Animals.Pedestrians.Bicycles and small motorcycles
moving at a low speed.
Shopping carts.Stationary objects on the road or
roadside.
Vehicles with shapes that may not
reflect radar waves.
Rear side radar sensors
The following systems utilize rear side
radar sensors.
Blind Spot Monitoring (BSM)Blind Spot Monitoring (BSM) Vehicle
Exit Warning
Rear Cross Traffic Alert (RCTA)Smart Brake Support (SBS) Rear
Crossing
Emergency Lane Keeping (ELK) Blind
Spot Assist
NOTE
When any of the following
conditions is met, the rear side radar
sensors may not be able to detect
target objects.
During inclement weather.The vehicle is driven on a sharp
curve or on bumpy roads.
Radar sensor from an adjacent
vehicle causes radio wave
interference.
The detection range of a front side
radar sensor is obstructed by an
adjacent wall or vehicle, or the
radar is reflected.
A vehicle suddenly enters the
detection range from the front or
side of your vehicle.
The target object is extremely
small.
The target object is extremely low/
high.
A vehicle approaches while
turning.
A vehicle that has stopped
suddenly starts to move.
Multiple objects move at the same
time.
The bumper around a rear side
radar sensor is deformed.
Foreign matter is adhering to the
bumper around a rear side radar
sensor.
The temperature near a rear side
radar sensor is extremely hot.
When towing a trailer.The rear side radar sensors may not
detect the following target objects.
Animals.Pe de st r ia ns .Bicycles and small motorcycles
moving at a low speed.
Shopping carts.Stationary objects on the road or
roadside.
Driving
Radar Sensors
5-133
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

Target object is thin such as wire,
rope, or poles.
Target object absorbs waves easily
such as cotton or snow.
Target object has an angular shape.Target object is tall and wide at the
upper part.
Target object height is low.There are multiple target objects.Target objects are too close to the
sensors.
Ice, snow, or mud is adhering to
the sensor area.
Heavy rainfall or pressurized water
is applied to the sensor area.
The sensor areas are frozen.You cover the sensor with your
hand.
The area around the sensor has
received a strong impact.
The vehicle is excessively tilted.Under extremely hot or cold
weather.
Approached by an object that
generates ultrasonic waves, such as
the horn of another vehicle, the
engine noise of a motorcycle, the
air brake noise of a large vehicle,
or the sensor of another vehicle.
A commercially-available fender
pole or an antenna for a radio
transmitter is installed to the
vehicle.
The vehicle is moving towards a tall
or square curbstone, or a steep
grade.
The vehicle is moving towards an
uneven wall or stairs.
The vehicle is driven in a place with
low ceilings.
The vehicle is driven on bumpy
roads, inclines, gravel roads, dense
grass, or grating.
The ultrasonic sensor does not detect
target objects directly beneath the
bumper. Even if target objects which
are located at a position lower than
an ultrasonic sensor have been
detected, the ultrasonic sensor may
suddenly stop detecting as the
vehicle approaches the target object.
Front ultrasonic sensors
The following systems utilize front
ultrasonic sensors.
Pa r k i n g S e n s o r
Rear ultrasonic sensors
The following systems utilize rear
ultrasonic sensors.
Smart Brake Support (SBS) reverse
drive detection
Pa r k i n g S e n s o r
Driving
Ultrasonic Sensors
5-136
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

How to Use the High
Beam Control System (HBC)
NOTE
The distance in which the HBC can
detect objects varies depending on
the surrounding conditions.
The Forward Sensing Camera (FSC)
may not be able to detect target
objects correctly, and the HBC may
not operate normally.
Refer to Forward Sensing Camera
(FSC) on page 5-127.
Using the HBC
Make sure that the light switch is in the
AUTO position.
The HBC determines the surrounding
conditions and operates automatically.
When the HBC operates, the HBC
indicator light (green)
in the
instrument cluster turns on.
Switching the headlights to high
beams
The HBC switches the headlights to
high beams when all of the following
conditions are met.
The vehicle speed is about 30 km/h
(19 mph) or faster.
The system does not detect a vehicle
ahead.
Switching the headlights to low
beams
The HBC switches the headlights to
low beams when any of the following
conditions is met.
The vehicle speed is less than about
20 km/h (12 mph).
When driving in areas with a
continuous line of street lamps or on
roads in well-lit cities and towns.
The system detects the headlights of
a vehicle ahead.
Canceling the HBC during operation
When the HBC is canceled, the HBC
indicator light (green)
in the
instrument cluster turns off.
Press the HBC switch again to make
the HBC operable.
NOTE
If the vehicle power is switched OFF
with the HBC turned off, the HBC
automatically turns on the next time
the vehicle power is switched ON.
Driving
High Beam Control System (HBC)
5-142
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

the instrument cluster screen display (white)
is not displayed.

In addition, when the door in the
direction in which an approaching
vehicle is detected is opened, the
driver is notified of the danger by
flashing of the warning lights, the
warning sound, and the instrument
cluster warning indication (amber).
BSM warning light
Instrument cluster
NOTE
The Vehicle Exit Warning may not
operate normally if any of the
following conditions is met.
The rear side radar sensors cannot
detect an object.
Refer to Radar Sensors on page
5-131.
There is a parked vehicle near your
vehicle.
Moving objects are slow.The Vehicle Exit Warning is not
automatically turned off even if a
Mazda genuine trailer hitch is used.
If a trailer is towed or a bicycle
carrier is attached to the rear of the
vehicle, the radar signal may be
blocked and the Vehicle Exit Warning
may not operate correctly.
The Vehicle Exit Warning may
operate with stationary objects on
the road or the roadside (such as
guardrails, sidewalls, and parked
vehicles).
The brightness of the BSM warning
lights is linked to the panel light
control.
Refer to Dashboard Illumination on
page 5-35.
Tu r n i n g off the BSM and the Vehicle
Exit Warning
There are 2 ways to turn off the BSM
and the Vehicle Exit Warning.
Tu r n
off the BSM and the Vehicle Exit
Warning using Mazda Connect.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
Tu r n off the BSM and the Vehicle Exit
Warning using the i-ACTIVSENSE
OFF switch.
Refer to How to Use the
i-ACTIVSENSE OFF switch on page
5-126.
Driving
Blind Spot Monitoring (BSM)
5-149
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

The vehicle is driven on slippery
roads such as icy roads,
snow-covered roads, and unpaved
roads.
 The vehicle is driven on a long
downslope.
 The vehicle is driven on a steep
slope.
 A two-wheeled vehicle such as a
motorcycle or bicycle is traveling
ahead.
Switch the MRCC off when it is not
being used.
Leaving the MRCC on when it is not in
use is dangerous as it could operate
unexpectedly, resulting in an accident.
Do not leave the vehicle while the
vehicle is stopped by the MRCC
control.
Getting out of the vehicle while the
stop hold control is operating is
dangerous as the vehicle may move
unexpectedly and result in an accident.
Before leaving the vehicle, switch the
MRCC off, shift the selector lever to
the P position, and apply the parking
brake.
CAUTION
 If the vehicle is towed or you are
towing something, switch the MRCC
off.
 Turn off the MRCC when the vehicle
is running on a chassis roller.
Driving
Mazda Radar Cruise Control (MRCC)
5-166
CX-90_8KG7-EA-22L_Edition1_new 2022-11-17 16:05:04

The vehicle is driven on slippery
roads such as icy roads,
snow-covered roads, and unpaved
roads.
 The vehicle is driven on a long
downslope.
 The vehicle is driven on a steep
slope.
 A two-wheeled vehicle such as a
motorcycle or bicycle is traveling
ahead.
 The vehicle is being towed or towing
another vehicle.
 Proximity warnings activate
frequently.
 Under bad weather conditions (rain,
fog , and snow).
 Tires other than the
specified size are
used, such as when tire chains or
temporary spare tires are used.
 The tire pressures are not adjusted to
the appropriate pressure.
 Tires with insufficient tread are used.
Switch the CTS off when it is not
being used.
Leaving the CTS on when it is not in
use is dangerous as it could operate
unexpectedly, resulting in an accident.
Do not leave the vehicle while the
vehicle is stopped by the CTS control.
Getting out of the vehicle while the
stop hold control is operating is
dangerous as the vehicle may move
unexpectedly and result in an accident.
Before leaving the vehicle, switch the
CTS off, shift the selector lever to the P
position, and apply the parking brake.CAUTION
 Heed the following cautions so that
the CTS can operate normally.
 Do not modify the suspensions.
 Always use wheels of the
specified
size for the front and rear wheels.
Consult an Authorized Mazda
Dealer for tire replacement.
 Turn off the CTS when the vehicle is
running on a chassis roller.
Driving
Cruising &
Tra ffi c Support (CTS)
5-176
CX-90_8KG7-EA-22L_Edition1_new
2022-11-17 16:05:04