2023 RAM CHASSIS CAB seats

314SAFETY
child restraint installation, instead of buckling it
behind the child restraint, route the seat belt
through the child restraint belt path and then
buckle it. Do not lock the seat belt. Remind all
children in the vehicle that the seat belts are not
toys and that they should not play with them.
Installing Child Restraints Using The
Vehicle Seat Belt
Child restraint systems are designed to be secured
in vehicle seats by lap belts or the lap belt portion
of a lap/shoulder belt. Regular Cab
The seat belts in the passenger seating positions
are equipped with a Switchable Automatic Locking
Retractor (ALR) that is designed to keep the lap
portion of the seat belt tight around the child
restraint so that it is not necessary to use a locking
clip. The ALR retractor can be “switched” into a
locked mode by pulling all of the webbing out of the
retractor and then letting the webbing retract back
into the retractor. If it is locked, the ALR will make
a clicking noise while the webbing is pulled back
into the retractor.
See the “Automatic Locking Mode” description
Ú
page 295 for additional information on ALR.
WARNING!
Improper installation of a child restraint to the
LATCH anchorages can lead to failure of the
restraint. The child could be badly injured or
killed. Follow the child restraint manufac -
turer’s directions exactly when installing an
infant or child restraint.
Child restraint anchorages are designed to
withstand only those loads imposed by
correctly-fitted child restraints. Under no
circumstances are they to be used for adult
seat belts, harnesses, or for attaching other
items or equipment to the vehicle.
WARNING!
Improper installation or failure to properly
secure a child restraint can lead to failure of
the restraint. The child could be badly injured
or killed.
Follow the child restraint manufacturer’s
directions exactly when installing an infant or
child restraint.

23_DPF_OM_EN_USC_t.book Page 314

SAFETY317
Installing A Child Restraint With A
Switchable Automatic Locking Retractor
(ALR):
Child restraint systems are designed to be secured
in vehicle seats by lap belts or the lap belt portion
of a lap/shoulder belt.

1.
For Crew Cab Models
Place the child seat in the center of the seating
position. If the second row seat can be re -
clined, you may recline the seat and/or raise
the head restraint (if adjustable) to get a better
fit. If the rear seat can be moved forward and
rearward in the vehicle, you may wish to move
it to its rear-most position to make room for the
child seat. You may also move the front seat
forward to allow more room for the child seat. For Regular Cab Models
Place the child seat in the center of the seating
position. Move the vehicle seat as far rearward
as possible to keep the child as far from the
passenger air bag as possible.
2. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the
child restraint. Do not twist the belt webbing in
the belt path.
3. Slide the latch plate into the buckle until you hear a “click.”
4. Pull on the webbing to make the lap portion tight against the child seat.
5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the
seat belt webbing out of the retractor. Then,
allow the webbing to retract back into the
retractor. As the webbing retracts, you will hear
a clicking sound. This means the seat belt is
now in the Automatic Locking mode.
6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any
webbing. If the retractor is not
locked, repeat
step 5.
7. Finally, pull up on any excess webbing to tighten the lap portion around the child
restraint while you push the child restraint
rearward and downward into the vehicle seat. 8. If the child restraint has a top tether strap and
the seating position has a top tether
anchorage, connect the tether strap to the
anchorage and tighten the tether strap. See
Úpage 318 for directions to attach a tether
anchor.
9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at
the belt path. It should not move more than
1 inch (25.4 mm) in any direction.
Any seat belt system will loosen with time, so check
the belt occasionally, and pull it tight if necessary.
Installing A Child Restraint With A Cinching
Latch Plate (CINCH) — If Equipped:
Child restraint systems are designed to be secured
in vehicle seats by lap belts or the lap belt portion
of a lap/shoulder belt.
WARNING!
Improper installation or failure to properly
secure a child restraint can lead to failure of
the restraint. The child could be badly injured
or killed.
Follow the child restraint manufacturer’s
directions exactly when installing an infant or
child restraint.
WARNING!
Improper installation or failure to properly
secure a child restraint can lead to failure of
the restraint. The child could be badly injured
or killed.
Follow the child restraint manufacturer’s
directions exactly when installing an infant or
child restraint.
6

23_DPF_OM_EN_USC_t.book Page 317

318SAFETY

1. Place the child seat in the center of the seating position. If the second row seat can
be reclined, you may recline the seat and/or
raise the head restraint (if adjustable) to get a
better fit. If the rear seat can be moved
forward and rearward in the vehicle, you may
wish to move it to its rear-most position to
make room for the child seat. You may also
move the front seat forward to allow more
room for the child seat.

2. Next, pull enough of the seat belt webbing from the retractor to pass it through the belt
path of the child restraint. Do not twist the belt
webbing in the belt path.
3. Slide the latch plate into the buckle until you hear a “click.”
4. Finally, pull up on any excess webbing to tighten the lap portion around the child
restraint while you push the child restraint
rearward and downward into the vehicle seat.
5. If the child restraint has a top tether strap and the seating position has a top tether
anchorage, connect the tether strap to the
anchorage and tighten the tether strap. See
Úpage 318 for directions to attach a tether
anchor. 6. Test that the child restraint is installed tightly
by pulling back and forth on the child seat at
the belt path. It should not move more than
1 inch (25.4 mm) in any direction.
Any seat belt system will loosen with time, so check
the belt occasionally, and pull it tight if necessary.
If the buckle or the cinching latch plate is too close
to the belt path opening of the child restraint, you
may have trouble tightening the seat belt. If this
happens, disconnect the latch plate from the
buckle and twist the short buckle-end belt up to
three full turns to shorten it. Insert the latch plate
into the buckle with the release button facing out,
away from the child restraint. Repeat steps 4 to 6,
above, to complete the installation of the child
restraint.
If the belt still cannot be tightened after you
shorten the buckle, disconnect the latch plate from
the buckle, turn the buckle around one half turn,
and insert the latch plate into the buckle again. If
you still cannot make the child restraint installation
tight, try a different seating position.
Installing Child Restraints Using The Top
Tether Anchorage
Regular Cab Trucks: In the regular cab truck, the top tether
anchorages are located behind the
center and right passenger seats. There
is a plastic cover over each anchorage.
To attach the tether strap of the child restraint:
WARNING!
Do not attach a tether strap for a rear-facing car
seat to any location in front of the car seat,
including the seat frame or a tether anchorage.
Only attach the tether strap of a rear-facing car
seat to the tether anchorage that is approved for
that seating position, located behind the top of
the vehicle seat. For the location of approved
tether anchorages in your vehicle, see
Ú page 310.

23_DPF_OM_EN_USC_t.book Page 318

SAFETY319

1. Place the child restraint on the seat and adjust the tether strap so that it will reach
over the seat back, under the head restraint
and to the tether anchor directly behind the
seat.

Regular Cab Tether Anchorages

2. Route the tether strap to provide the most direct path between the anchorage and the
child seat. The tether strap should go between
the head restraint posts underneath the head
restraint. You may need to adjust the head
restraint to the upward position to pass the
tether strap underneath the head restraint
and between its posts. 3. Lift the cover (if so equipped), and attach the
hook to the square opening in the sheet metal.
Tighten the tether strap according to the child
seat manufacturer’s instructions.
Crew Cab Trucks The top tether anchorages in this vehicle
are tether strap loops located between
the rear glass and the back of the rear
seat. There is a tether strap loop located
behind each seating position. Follow the steps
below to attach the tether strap of the child
restraint.
Right Or Left Outboard Seats:

1. Raise the head restraint and reach between the rear seat and rear glass to access the
tether strap loop.
Head Restraint In Raised Position
Tether Strap Loop With Center Head Restraint In Raised Position

1 — Tether Anchor
2 — Tether Strap Hook
3 — Tether Strap To Child Restraint
WARNING!
Never place a rear-facing child restraint in front
of an air bag. A deploying Passenger Front Air
Bag can cause death or serious injury to a child
12 years or younger, including a child in a
rear-facing child restraint.
6

23_DPF_OM_EN_USC_t.book Page 319

320SAFETY
2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the
seat back, under the head restraint, through
the tether strap loop behind the seat and over
to the tether strap loop behind the center seat.
3. Pass the tether strap hook under the head restraint behind the child seat, through the
tether strap loop behind the seat and over to
the center tether strap loop.

Tether Strap Through Outboard Tether Strap Loop

4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap
according to the child seat manufacturer’s
instructions.
Tether Strap Through Outboard Tether Strap Loop And
Attached To Center Tether Strap Loop

NOTE:If there are child seats in both of the outboard (left
and right) seating positions, the tether strap hooks
of both child seats should be connected to the
center tether strap loop. This is the correct way to
tether two outboard child seats.
Center Seat:

1. Raise the head restraint and reach between the rear seat and rear glass to access the
tether strap loop.
Tether Strap Loop With Head Restraint In Raised Position

2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the
seat back, under the head restraint, through
the tether strap loop behind the seat and over
to the tether strap loop behind either the right
or left outboard seat.
3. Pass the tether strap hook under the head restraint behind the child seat, through the
tether strap loop behind the seat and over to
the right or left outboard tether strap loop.

23_DPF_OM_EN_USC_t.book Page 320

322SAFETY
TRANSPORTING PETS
Air Bags deploying in the front seat could harm
your pet. An unrestrained pet will be thrown about
and possibly injured, or injure a passenger during
panic braking or in a collision.
Pets should be restrained in the rear seat (if
equipped) in pet harnesses or pet carriers that are
secured by seat belts.
CONNECTED VEHICLES
Privacy of any wireless and wired communications
cannot be assured. Third parties may unlawfully
intercept information and private communications
without your consent. For further information, refer
to “Data Collection & Privacy” in your Uconnect
Owner’s Manual Supplement or “Onboard
Diagnostic System (OBD II) Cybersecurity”
Úpage 111.
SAFETY CHECKS YOU SHOULD MAKE
I
NSIDE THE VEHICLE
Seat Belts
Inspect the seat belt system periodically, checking
for cuts, frays, and loose parts. Damaged parts
must be replaced immediately. Do not
disassemble or modify the system.
If your vehicle is involved in a collision, or if you
have questions regarding seat belt or retractor
conditions, take your vehicle to an authorized FCA
dealer or authorized FCA Certified Collision Care
Program facility for inspection.
Air Bag Warning Light
The Air Bag Warning Light will turn on for
four to eight seconds as a bulb check
when the ignition switch is first placed in
ON/RUN. If the light is either not on
during starting, stays on, or turns on while driving,
have the system inspected at an authorized dealer
as soon as possible. After the bulb check, this light
will illuminate with a single chime when a fault with
the Air Bag System has been detected. It will stay
on until the fault is removed. If the light comes on
intermittently or remains on while driving, have an
authorized dealer service the vehicle immediately
Ú page 288.
Defroster
Check operation by selecting the defrost mode and
place the blower control on high speed. You should
be able to feel the air directed against the
windshield. See an authorized dealer for service if
your defroster is inoperable.
Floor Mat Safety Information
Always use floor mats designed to fit your vehicle.
Only use a floor mat that does not interfere with the
operation of the accelerator, brake or clutch
pedals. Only use a floor mat that is securely
attached using the floor mat fasteners so it cannot
slip out of position and interfere with the
accelerator, brake or clutch pedals or impair safe
operation of your vehicle in other ways.
Do not allow people to ride in any area of your
vehicle that is not equipped with seats and
seat belts.
Be sure everyone in your vehicle is in a seat
and using a seat belt properly.
WARNING!WARNING!
It is not possible to know or to predict all of the
possible outcomes if your vehicle’s systems are
breached. It may be possible that vehicle
systems, including safety related systems, could
be impaired or a loss of vehicle control could
occur that may result in an accident involving
serious injury or death.

23_DPF_OM_EN_USC_t.book Page 322

380SERVICING AND MAINTENANCE
F22 20 Amp Blue
–Gas – ECM *
25 Amp White Diesel – PCM *
F23 30 Amp Pink –CBC #1 / Int Light
F24 30 Amp Pink –Driver Door Mod
F25 30 Amp Pink –FT Wiper
F26 ––Spare
F27 ––Spare
F28 20 Amp Blue –TRLR Tow B / U
F29 20 Amp Blue –TRLR TOW PARK
F30 30 Amp Pink –TRLR Tow
F31 ––Spare
F32 ––Spare
F33 20 Amp Blue –Trans Control Mod *
F34 30 Amp Pink –VSIM #2 *
F35 30 Amp Pink –Sunroof *
F36 30 Amp Pink –Rear Defroster (EBL) *
F37 30 Amp Pink –Diesel Frame / Fuel HTR *
F38 30 Amp Pink –ITBM *
F39 ––Spare
F40 –10 Amp RedVented Seats *
Cavity Cartridge Fuse Micro FuseDescription
* If Equipped

23_DPF_OM_EN_USC_t.book Page 380

SERVICING AND MAINTENANCE383
F80 –10 Amp RedOvrdh Con / Assist / 911
F81 –20 Amp YellowTrlr tow Rt turn / Stop
F82 –10 Amp RedSCCM / Cruise control
F83 –10 Amp RedTLR AST / TLR RVS CTL / TLR KNB
F84 –15 Amp Blue
ASBM / HVAC / ICS / R Heated Seats SW

F85 –10 Amp RedORC (Airbag)
F86 –10 Amp RedORC (Airbag)
F87 –10 Amp RedAir Susp / ITBM / SCCM / TLR TPM
F88 –15 Amp BlueIP Cluster
F89 ––Spare
F90 –20 Amp YellowPower Outlet / Batt
F91 ––Power Outlet / Acc
F92 –10 Amp RedInvertor MOD / USB-IP / WCPM *
F93 ––Spare
F94 –10 Amp RedSBW / TCASE SW / TRL TPM - GTWY
F95 –10 Amp RedRR CAM / PRKTRNX/ CHMSL Cam /
Bld SPT SNR / SVUE CAM *
F96 –10 Amp RedTRL Cam *
F97 –20 Amp YellowFront HTD ST PSGR *
F98 –20 Amp YellowFront HTD ST DRIVER *
Cavity Cartridge Fuse Micro FuseDescription
* If Equipped
8

23_DPF_OM_EN_USC_t.book Page 383