2023 RAM 1500 tow

GETTING TO KNOW YOUR VEHICLE67
(Continued)
When the vehicle is turned off, be sure to unplug any
equipment as to not drain the battery of the vehicle. All
accessories connected to the outlet(s) should be removed
or turned off when the vehicle is not in use to protect the
battery against discharge.
POWER INVERTER — IF EQUIPPED
A 115 Volt (400 Watts maximum) inverter may be located
inside the center console towards the right hand side. This
inverter can power cellular phones, electronics and other
low power devices requiring power up to 400 Watts.
Certain video game consoles exceed this power limit, as
will most power tools.

Center Console Power Inverter Outlet

There is also a second 115 Volt (400 Watts maximum)
power inverter located on the rear of the center console.
This inverter can power cellular phones, electronics and
other low power devices requiring power up to 400 Watts. Certain video game consoles exceed this power limit, as
will most power tools.
All power inverters are designed with built-in overload
protection. If the power rating of 400 Watts is exceeded,
the power inverter shuts down. Once the electrical device
has been removed from the outlet the inverter should
reset.

Rear Center Console Power Inverter Outlet

NOTE:
400 Watts is the maximum for the inverter, not each
outlet. If three outlets are in use, 400 Watts is shared
amongst the devices plugged in.
If equipped with a front bench seat, there may be a
115 Volt (400 Watts maximum) inverter located to the
right of the center stack, just below the climate controls.
This inverter can power cellular phones, electronics and
other low power devices requiring power up to 400 Watts.
WARNING!
To avoid serious injury or death:
 Only devices designed for use in this type of outlet
should be inserted into any 12 Volt outlet.
 Do not touch with wet hands.
 Close the lid when not in use and while driving the
vehicle.
 If this outlet is mishandled, it may cause an electric
shock and failure.
CAUTION!
Many accessories that can be plugged in draw power
from the vehicle's battery, even when not in use
(i.e., cellular phones, etc.). Eventually, if plugged in
long enough, the vehicle's battery will discharge suffi -
ciently to degrade battery life and/or prevent the
engine from starting.
 Accessories that draw higher power (i.e., coolers,
vacuum cleaners, lights, etc.), will discharge the
battery even more quickly. Only use these intermit -
tently and with greater caution.
 After the use of high power draw accessories, or long
periods of the vehicle not being started (with acces -
sories still plugged in), the vehicle must be driven a
sufficient length of time to allow the generator to
recharge the vehicle's battery.
CAUTION!
2

23_DT_OM_EN_USC_t.book Page 67

GETTING TO KNOW YOUR VEHICLE79
NOTE:Once the spring load is overcome, the bed step will extend
out quickly, so be sure to stand in a position that will avoid
coming into contact with the step as it extends.
To stow the bed step back under the tailgate, push the bed
step forward with your foot until the bed step is retracted
by the spring load.
Bed Step For Multifunction Tailgate

Bed Step Location

To extend the bed step, place your foot on the top center
of the bed step, and push down while pulling rearward.
A small amount of force will release the spring load and
extend the bed step out and away from the tailgate.

Bed Step Extended

NOTE:
Once the spring load is overcome, the bed step will extend
out quickly. Be sure to stand in a position that will avoid
coming into contact with the step as it extends.
To stow the bed step back under the tailgate, push the bed
step forward with your foot until the bed step is retracted
by the spring load.
PICKUP BOX
The pickup box has many features designed for utility and
convenience.

Pickup Box Features

NOTE:
If you are installing a Toolbox, Ladder Rack or Headache
Rack at the front of the Pickup Box, you must use Mopar®
Box Reinforcement Brackets that are available from an
authorized dealer.
WARNING!
Do not attempt to stow the bed step with your hands.
The low clearance space between the bed step and the
rear bumper as the bed step returns to the stowed
position could result in injury to your hands or fingers.
WARNING!
Do not attempt to stow the bed step with your hands.
The low clearance space between the bed step and the
rear bumper as the bed step returns to the stowed
position could result in injury to your hands or fingers.
1 — Upper Load Floor Indents
2 — Bulk Head Dividers
3 — Cleats
2

23_DT_OM_EN_USC_t.book Page 79

GETTING TO KNOW YOUR VEHICLE85
Extender Position
The extender position allows you to load the bed of the
truck beyond the tailgate. The bed extender will add an
additional 15 inches (38 cm) in the back of the truck when
additional cargo room is needed. The extender position
utilizes a locating pin and rotating handle located on both
sides of the truck bed near the tailgate.

Extender Position

To install the bed extender into the extender position,
perform the following:

1. Lower the tailgate.

2. Make sure the center handle is unlocked and rotate
the center handle vertically in order to release the
extender side gates.
3. Fit the end of the side gate ends onto the pin and handle.

Extender Installation

4. Rotate the handles to the horizontal position to secure into place.

Locking Tab

Storage Position
The storage position for the bed divider is at the front of
the truck bed which maximizes the bed cargo area when
not in use.
WARNING!
To reduce the risk of potential injury or property
damage:
Cargo must be secured.
 Do not exceed cargo load rating of your vehicle.
 Secure all loads to truck utilizing cargo tie downs.
 Extender should not be used as cargo tie down.
 When vehicle is in motion do not exceed 150 lb
(68 kg) load on the tailgate.
 The bed extender is not intended for off road use.
 When not in use, the extender/divider should be in
stowed or divider position with the tailgate closed.
 When in use all handles are to be in the locked
position.
2

23_DT_OM_EN_USC_t.book Page 85

86GETTING TO KNOW YOUR VEHICLE
To install the bed divider into the storage position, perform
the same steps as you would for the divider position,
except position the divider fully forward in the bed against
the front panel.

Storage Position

The outboard ends should be positioned in front of the
cargo tie-down loops.

Cargo Tie-Down Loop

TRI-FOLD TONNEAU COVER — IF EQUIPPED
The Tri-Fold Tonneau Cover can be installed on the truck
bed to protect your gear and cargo.
TONNEAU COVER COMPONENTS

Folded Tonneau Cover Components Tonneau Cover Latch Components
Position One
(Front Latches Latched And Stowage Straps Secured)

1 — Stowage Strap
2 — Tonneau Cover Bumper Folded
1 — Handle
2 — Slide Locking Lever
3 — Locating Bumper
4 — Truck Flange Bead
5 — Latch Bumper
6 — J Hook

23_DT_OM_EN_USC_t.book Page 86

GETTING TO KNOW YOUR VEHICLE87

Position Two (Front And Rear Latches Latched)

TRI-FOLD TONNEAU COVER FOLDING
F
OR DRIVING OR REMOVAL
To remove the Tonneau Cover use the following steps:

1. Open the tailgate to access the rear pair of Tonneau
Cover latches located on the underside of the Cover.

Location Of Rear Latches
Slide Locking Lever Inward

2. Slide the locking lever toward the inside of the truck bed to release the J Hook and pull the handle
downward into the released position.

Unlatching Latch
Released Position

1 — Panel 1
2 — Panel 2
3 — Panel 3
2

23_DT_OM_EN_USC_t.book Page 87

88GETTING TO KNOW YOUR VEHICLE

Hold The Bumper And Push The Handle Up

3. Holding the bumper, push the fully released latch to
the center and push up. Push the handle firmly,
locking it into the stowed position. Repeat Steps 2
and 3 for the opposite side latch.

Stowed Position Lift Panel 3 And Fold Onto Panel 2

4. Lift up on Panel 3 and fold it onto Panel 2.

Correct Folding — Hold Panels Together
NOTE:
When folding the second and third panels, the sections
MUST
be held together to avoid damage to the cover
material. Fold the panel gently. Do not allow the panels to
drop under their own weight.

Incorrect Folding — Will Cause Damage

5. Lift up on the second and third panel and fold them onto the first panel.

Stowage Strap Clipped

23_DT_OM_EN_USC_t.book Page 88

GETTING TO KNOW YOUR VEHICLE89
6. Unsnap the stowage strap and clip. Repeat for both
straps to prevent the Tonneau Cover panels from
unfolding.

Position One
(Front Latches Latched And Stowage Straps Secured)

NOTE:
Be sure the Tonneau Cover has been folded completely,
and the stowage straps are engaged, before removing.

Fully Folded Tonneau Cover

NOTE:
The vehicle can be driven with the Tonneau Cover in the
folded position or can be completely removed.

Slide Locking Lever Inward

7. Slide the locking lever toward the inside of the truck bed to release the J Hook and pull the handle
downward into the released position.

Unlatching Latch
Released Position

CAUTION!
The folded Tonneau Cover must be latched by both
front latches and both front stowage straps or damage
to the Tonneau Cover or vehicle may occur while driving.
2

23_DT_OM_EN_USC_t.book Page 89

90GETTING TO KNOW YOUR VEHICLE

Hold The Bumper And Push The Handle Up

8. Holding the bumper, push the fully released latch to
the center and push up. Push the handle firmly,
locking it into the stowed position. Repeat Steps 2 &
3 for the opposite side latch.
9. With two people, remove the cover.
TRI-FOLD TONNEAU COVER
I
NSTALLATION
To install the Tonneau Cover follow these steps:

1. Position the Tonneau Cover on the truck bed and
center using the locating bumpers.

2. Locate the front pair of Tonneau Cover latches on the underside of the Cover. Slide the locking lever toward
the inside of the truck bed and release the latch from
the stowed position, and pull the handle downward
into the released position. Do this for both the left and
right side.

Location of Front Latches
Slide Locking Lever Towards Inside Of Truck Unlatching Latch
Released Position

3. Swing the J Hook from the handle and push the handle to the center and up, ensuring that the J Hook
is under the truck flange. Push up on the handle
firmly, locking it into the latched position.

23_DT_OM_EN_USC_t.book Page 90