2023 KIA STINGER mirror

STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED33
To operate:
•Move lever up/down to change wiper modes
–MIST: Single wipe
–OFF: Wiper off
–AUTO: Auto Rain Sensing
–LO: Slow wipe
–HI: Fast wipe
•
Pull to spray and wipe
Auto Rain Sensing
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO .
To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .
MIST
OFF
AUTO LOHIAUTO
Windshield Wipers & Washers
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Lifting Wipers / Wiper Service Mode Video
QR CODES
•
When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•
Set the wiper to the OFF position when the wiper is not in use
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the Smar t Power Liftgate* lid control, turn off the auto rain sensing wipers and fold in the mirrors
•
Moving lever to HI increases Intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•
Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton down decreases frequency of wipes
QUICK TIPS
A
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace wiper blades or raise wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the service position B .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch to the MIST position C and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to normal position, turn the ignition ON, then activate MIST .See section 4 in the Owner’s Manual for more information .
B
C

CENTER PANEL
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED47
CENTER PANEL
P
R
N
D
AUTO
HOLD
DRIVE MODEOFFOFF
P
To shift into any gear from Park, depress the brake pedal, then press the
Unlock button A , located on the side of the gear shift lever, and shift .
P: Park – To shift into Park from any gear, press the P button B on the gear shift while vehicle is stationary and the brake pedal is depressed (Shift by Wire only) .
R: Reverse – To shift into Reverse from Drive, depress the brake pedal, press the Unlock button A , and move the shift lever forward twice to skip over Neutral and into Reverse .
N: Neutral
D: Drive
P
R
N D
+
-
4IJGU
CZ
8JSF
U ZQF
TIPXO
4IJGU
CZ
$BCMF
U ZQF
TIPXO

Automatic Transmission (Shift by Cable* / Shift by Wire*)
and Manual Shift Mode (Shift by Cable only)
(Paddles on rear side of steering wheel)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Automatic Transmission Control (Shift by Wire) Video
Automatic Transmission with Paddle Shifters
QR CODE
Paddle Shifters
•Press the Unlock but ton A when shifting from P (Park) to any gear
•The instrument cluster and the light on top of the shift lever identifies the gear the vehicle is currently in
QUICK TIPS
REMINDERS:
•
Press and hold the [+} right paddle shifter to return to Automatic mode (Shift by Wire* only)
•
When in Manual Shift mode, pulling the left and right paddle shifters at the same time will NOT shift gears
•
When in P (Park), if the Unlock but ton is not pressed while shifting, the transmission does not shift
•
If the vehicle is turned off while in Neutral without shifting into Park, it will remain in Neutral until the driver ’s door is opened . At that point it will automatically shift into Park
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the power liftgate lid control, turn off the auto rain sensing wipers and fold in the mirrors
A
AB
Paddle Shifters: With the gear shift in Drive, pull the paddle shifter to manually change gears .
[+]: Manual Mode Upshift*
[–]: Manual Mode Downshift*

S E AT I N G
SEATING
Driver Position Memory System*
The integrated system stores into memory the position of the driver ’s seat, outside rearview mirrors, steering wheel positions and seat cushion extension* . To store positions into memory, first place the gear shift into P (Park) while the Engine Star t/Stop button is in the ON position . Then:
1 .
Adjust the driver ’s seat, outside rearview mirrors, settings and steering wheel positions
2 .
Press the SET button B on the control panel . System will BEEP once
3 .
Press one of the memory buttons 1 or 2 C within 4 seconds . The system will BEEP twice when memory has been stored
(Located on driver ’s door control panel)
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED52STINGER FEATURES & FUNCTIONS GUIDE
REMINDERS:
•But ton may be hard to see if headrest is in its lowest position
•
Do not operate the vehicle with the headrests removed . Headrests can provide critical neck and head suppor t in an accident . Do not at tempt to adjust the seat while the vehicle is moving . This could result in loss of control of the vehicle .
See section 3 in the Owner’s Manual for more information .
REMINDER: Do not operate the vehicle with the headrests removed . Headrests can provide critical neck and head suppor t in an accident .
See section 3 in the Owner’s Manual for more information .
To raise headrest: Pull headrest up .
To lower headrest: Press the lock button A , then press the
headrest down .
Front Seat Headrest Adjustment†7
A
B
C
•
For easy adjustments, hold a headrest post with one hand while using the other hand to pull the headrest from underneath
QUICK TIP

ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED53
How to Sync Transmitter with HomeLink®
If programming for the first time, begin with Step 1 (repeating this step will delete all information) .
To program non-rolling and rolling code garage door openers and other devices:
1 . Press and hold the left A and center C buttons simultaneously until the indicator light G begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button A B C and hold the button on the transmitter while it is approximately 1 to 3 inches away from the mirror . The HomeLink® Indicator light F will flash rapidly once the frequency signal has been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
3 . Locate the “learn” or “smart ” button on the garage door ’s motor head unit . Press and release the button and complete Step 4 within 30 seconds
4 . Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the A and C buttons simultaneously for approximately 20 seconds, and then release both buttons within 30 seconds .
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to reduce glare from a vehicle’s headlights located in the rear and also connect up to three electronic transmitters into one location .
HomeLink®†2 with Auto-Dimming Rearview Mirror*
A HomeLink® Channel 1
B HomeLink® Channel 2
C HomeLink® Channel 3
D Garage Door Opener Status Indicator: Closing or Closed
E HomeLink® Operation Indicator
F Garage Door Opener Status Indicator: Opening or Open
G HomeLink® User Interface Indicator
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
HomeLink® Support
QR CODE
•
You can reprogram a single HomeLink but ton by repeating Step 2
•Erasing the programmed but tons will delete all trained transmit ters
QUICK TIPS
ABC
D
EF
G
OTHER KEY

FEATURES
OTHER KEY FEATURES

Smart Power Liftgate*† 11 (Continued)
HOLD
See section 4 in the Owner’s Manual for more information .
Opening with no-touch activation:
When the Smart Key fob is on your person and you are within close proximity
of the back of the vehicle, the hazard lights will blink and a chime will sound for about 3 seconds as an alert that the Smart Power Liftgate is about to open .
Then the alert system will blink and chime two additional times before opening the Smart Power Liftgate .
The Smart Power Liftgate feature is OFF by default . To enable the Smart Power Liftgate, go to User Settings in the LCD Instrument Cluster modes .
Smart Key:
Using the Smart Key fob to automatically open the Smart Power Liftgate*, press and hold the Smart Key Liftgate button A . Press again and hold to close .
OTHER KEY FEATURES
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Kia Smart & Folding Key Fob Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED57
OTHER KEY

FEATURES
A
•
The Liftgate must be unlocked before it can be opened by the Liftgate Release but ton
•
The Liftgate unlocks automatically and then can be opened manually when the Smar t Key is within close proximit y to the back of the vehicle
QUICK TIPS
REMINDERS:
•
Smar t Power Liftgate may be damaged if at tempting to open or close manually
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the Smar t Power Liftgate lid control using the but ton inside the glove compar tment, turn off the auto rain-sensing wipers and fold in the mirrors
•
When not in use, keep the Liftgate Lid Control but ton in the OFF position
•
Ensure all obstacles are out of the way of the Liftgate lid when operating the Smar t Power Liftgate