2023 KIA STINGER ECO mode
[x] Cancel search: ECO modePage 16 of 72
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEM (ADAS)
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED14STINGER FEATURES & FUNCTIONS GUIDE
Lane Keeping Assist (LKA)†3
Lane Keeping Assist is designed to detect the lane markers (or road edges) on the road with a front view camera on the windshield, as far as it can based on environmental conditions, and may assist the driver ’s steering to help keep
the vehicle in the lane . When turned on, the instrument cluster indicator will initially illuminate white . It will remain white when the vehicle is traveling slower than 40 mph or when the function does not detect the lane markers . When the system detects the lane markers and can assist the steering, the Lane Safety icon will illuminate green .
If LK A detects that you are moving outside of your lane, the system may give an audible warning and display Lane Departure Warning on the instrument cluster . If the vehicle continues to move outside of the lane, LK A may provide steering, trying to prevent the vehicle from moving outside its lane .
When enabled and turned on (see below), press the Lane Safety button A to activate or deactivate LK A .
LKA Settings:
•Press and hold the Lane Driving Assist button B to turn LK A on or off, when it is first enabled in the User Settings* in the Instrument Cluster or Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is on or the Engine Start/Stop button* in the on position
•To access User settings* in the Instrument Cluster - Press the Mode button C on the Steering Wheel to toggle to User Settings . Press the OK D up/down to toggle to Driver Assistance and then Lane Safety
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button . Press VEHICLE to enter Vehicle Settings . Select Driver Assistance and then Lane Safety
•LK A Modes – Select one of the following:
–Assist: LK A will automatically assist the driver ’s steering, when lane departure is detected, to help prevent the vehicle from moving out of its lane
–Warning Only: LK A will warn the driver with an audible warning when lane departure is detected . In this mode the function will not provide steering inputs
–Off: LK A will turn off . The indicator light E will turn off on the cluster
•All functions will operate under the following conditions:
–The vehicle speed exceeds approximately 40 mph
–
LK A recognizes one side of the lane markers the vehicle is traveling in
–
The vehicle is between the lane markers
(But ton layout on right of steering wheel)
(But ton layout to the left of steering wheel)
Lane Keeping AssistLane Keeping Assist
When engaged, Lane Keeping Assist is not a substitute for safe driving and may not always warn the driver . Always drive safely and use caution .
For illustrative purposes only . Your actual display, buttons and/or features may vary . Actual User Settings steps may vary by model . Refer to section 5 in the Owner’s Manual for more information .
When the front-view camera detects the vehicle moving outside of the lane it is traveling in, a vehicle crossing line indicator will blink, either on the left or right lane (as shown in both images above)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Keeping Assist (LKA) Video
QR CODE
REMINDERS:
•
LK A may not detect lane markers in cer tain environment conditions
•
LK A will not issue a warning if the turn signal or hazard signal is activated
•
LK A will return to its previous state when the ignition is cycled
A
Lane Keeping Assist
When the front-view camera does not detect the lane traveling in, the lines are illuminated grey
When the front-view camera detects the lane traveling in, both lines are illuminated green
Lane Keeping Assist
E
OKD
B
C
Page 20 of 72
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEM (ADAS)
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED18STINGER FEATURES & FUNCTIONS GUIDE
OK
(But ton layout on right of steering wheel)
Driver Attention Warning (DAW)†4
Driver Attention Warning is designed to alert the driver if it detects inattentive driving practices and, in certain situations, can give a warning signal to take a break from driving .
•Inattentive Driving Warning: DAW will inform the driver of the driver ’s attention level and will recommend taking a break when it falls below a certain level
•Leading Vehicle Departure Alert: DAW will inform the driver when the front vehicle departs from a stop
If DAW is activated, the DAW information will appear on the Instrument Cluster LCD Display when you select the Driving Assist menu . A message, “Consider taking a break,” A appears on the LCD and a warning sounds to suggest the driver take a break when the driver ’s attention level becomes low B .
DAW User Settings:
•DAW can be turned on/off by going to the User Settings* in the Instrument Cluster or the Vehicle Settings* in the Infotainment System
•Only adjust settings when the vehicle is at a standstill, gear shift is in Park and the ignition is turned on or the Engine Start/Stop button* in the ON position
•To access User settings* in the Instrument Cluster - Press the Mode button C on the Steering Wheel to toggle to User Settings . Press the OK button D up/down to toggle to Driver Assistance, then Driver Attention Warning and select Inattentive Driving
•To access Vehicle settings* in the Infotainment System – Press the SETUP key or the onscreen SETUP button . Press VEHICLE to enter Vehicle Settings . Select Driver Assistance, then Driver Attention Warning and select Inattentive Driving
•DAW Warning Timing – When in the Driver Assistance menu, select
Warning Timing and one of the following:
–Normal: Driver Attention Warning warns the driver of his/her inattentive driving practices
–Late: Driver Attention Warning warns the driver of his/her inattentive driving practices later than Normal mode
REMINDERS:
•
The set-up of DAW will be maintained, as selected, when the ignition is cycled
•
When activated, DAW does not display the “Consider taking a break ” message when the total trip driving time is less than 10 minutes
•
DAW will enter a standby mode if the camera does not detect the lanes
Consider taking a break
Attention Level
High
When engaged, Driver Attention Warning is not a substitute for safe driving and may not detect all instances of inattentive driving practices . Failure to pay attention to travel conditions and vehicle operation could result in loss of vehicle control . Always drive safely and use caution .
Refer to section 5 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Driver Attention Warning (DAW) Video
QR CODE
ABC
D
Page 22 of 72
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEM (ADAS)
Navigation-based Smart Cruise Control will help automatically adjust vehicle speed when driving on highways with posted speed limits by using road information from the navigation system, while Smart Cruise Control
is operating .
Smart Cruise Control is designed to maintain a predetermined distance from vehicles detected ahead by automatically adjusting the driving speed as needed . When traffic is detected, the vehicle will slow down to maintain a set distance behind traffic without depressing the accelerator or brake pedal .
Highway Curve Zone Auto Slowdown: NSCC can automatically adjust the vehicle speed when it detects a curved road ahead and when it receives road information from the navigation system . When NSCC detects a curve ahead, NSCC activates and reduces the vehicle speed, and the AUTO icon A (nex t
page) in the NSCC indicator turns green . When the vehicle passes the curved road, the vehicle may return to its previously set speed .
Highway Auto Speed Change: If the set speed is set to the current posted speed limit on the highway during NSCC operation, the set speed is changed automatically whenever the posted speed limit changes and when it receives information from the navigation system .
SCC Operation: With SCC turned on and activated, the vehicle distance set, and the system detects a vehicle slowing or stopping, the system can bring the vehicle to a complete stop . When the vehicle ahead starts to move forward, SCC re-engages . If the vehicle ahead stops for more than 3 seconds, the accelerator pedal or the + – button B must be pressed to start moving the vehicle .
SCC will adjust acceleration based on the drive mode selected in the Drive Mode Integrated Control system .
NSCC Settings:
To turn on/set/adjust the NSCC speed: Press the Driving Assist button C on the Steering Wheel to activate NSCC and the speed will be set to the current vehicle speed . NSCC may decrease the speed to maintain the distance with the vehicle in front . The CRUISE indicator will illuminate on the instrument cluster .
Press the + – button B up/down to accelerate/decelerate to the desired speed . Press the button B to set the speed .
To set the vehicle distance: Press the Vehicle Distance button D on the steering wheel . Each time you press the button, the vehicle distance will change G, indicated by the number of bars that appear on the display A .
To pause/resume NSCC operation: Depress the brake pedal or press the Pause/Resume button + – B . The cruise indicator on the instrument cluster will change .
To turn NSCC OFF: Press the Driving Assist button C . The CRUISE indicator on the instrument cluster will turn OFF .
To adjust the sensitivity of NSCC: Press the mode button E on the Steering Wheel . With the OK button F, select Drive Assistance, then NSCC Response . Then select Fast, Normal or Slow .
Images are for illustrative purposes only and may not reflect actual feature or operation .
Navigation-based Smart Cruise Control (NSCC)†3
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Smart Cruise Control with Overtaking Acceleration Assist Video
Navigation-based Smart Cruise Control - (NSCC) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED20STINGER FEATURES & FUNCTIONS GUIDE
OK
OK
CE
FB
D
Page 25 of 72
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEM (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED23
Rear View Monitor (RVM)†3
Rear View Monitor is a supplemental function that displays the view behind the vehicle through the audio head unit screen while the vehicle is in Reverse .
Rear View Monitor activates when the:
•Engine Start/Stop button is in the ON position
•Gear Shift Lever is in the R (Reverse) position
REMINDERS:
•
Through normal use and after inclement weather or washing, the rear camera may become dir t y . Use a clean, microfiber cloth to remove any dir t, debris or spots that may have accumulated on the lens
•
RVM is not a substitute for proper and safe backing-up procedures
•
RVM may not display ever y object behind the vehicle
•
Always drive carefully and use caution when backing up
P
R
N
D
AUTO
HOLD
DRIVE MODEOFF
Rear View Monitor is not a substitute for proper and safe backing-up procedures . Rear View Monitor may not display every object behind the vehicle . Always drive safely and use caution when backing up .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 4 in the Owner’s Manual for more information .
Surround View Monitoring is only a supplemental system . Drivers should not rely solely on the SVM information when parking and backing up . Drivers should always pay attention and directly check the left/right and rear .
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
P
P
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 4 in the Owner’s Manual for more information .
(But ton located below gear shift)
Surround View Monitor (SVM)*†3
Surround View Monitor is a parking support system that shows the areas around the front, rear, left and right sides of the vehicle via four cameras displayed onto the infotainment system screen .
•
Press the Parking/ View button A to turn on Surround View Monitor . Press the button again to turn off the function
•
Other view modes can be selected by touching the view icons B on the Surround View Monitor screen
•Surround View Monitor Auto On: To this feature on, go to Driver
Assistance in the Vehicle Settings > Parking Safety > Surround View Monitor Auto On . When turned on, vehicle is in D (Drive) and the Parking Distance Warning sounds, the front parking assist view is displayed
To change the SVM settings, press the onscreen settings icon C, while SVM is operating .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Surround View Monitor (SVM) Video
QR CODE
A
B
C
REMINDERS:
•
The SVM camera is equipped with an optical lens to provide a wider range of vision and may appear different from the actual distance
•
Through normal use and after washing or inclement weather, the rear camera may need cleaning . Use a clean, microfiber cloth to remove any dir t, debris or spots that may have accumulated on the lens
•The Front View of SVM will turn off when the gear shift is moved into Park or Reverse or the Parking/ View but ton is pressed .
QUICK TIP
Page 27 of 72
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEM (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED25
Forward*/Reverse Parking Distance Warning (PDW)†3
Forward*/Reverse Parking Distance Warning (PDW) A is a supplemental system that is designed to assist the driver by chiming if an object is detected within the sensing areas in the front or rear of the vehicle when
moving forward or backing up .
When the Engine Start/Stop button is ON and the shift lever is in R (Reverse), the system is activated and the Forward*/Reverse Parking Distance Warning (PDW) button indicator is illuminated .
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFFOFF
P
3 F B S T F O T P S T T I P X O
' P S X B S E 3 F W F S T F 1 B S L J O H % J T U B O \
D F 8 B S O J O H J T O P U B T V C T U J U V U \
F G P S Q S P Q F S B O E T B G F C B D L J O H V Q \
Q S P D F E V S F T " M X B Z T E S J W F \
T B G F M Z B O E V T F D B V U J P O X \
I F O C B D L J O H V Q\
' P S X B S E 3 F W F S T F 1 B S L J O H % J T U B O \
D F 8 B S O J O H 1 % 8
\
N B Z O P U E F U F D U F W F S Z P C K F D U J O G S P O U P \
G P S C F I J O E U I F W F I J D M F
4 F F T F D U J P O J O U I\
F 0 X O F S s T . B O V B M G P S N P S F J O G P S N B U J P O
3 F G F S U P U I F J O T J E F G S P O U D P W F S G P S N P S F J O G P S N B U J P O P O 2 3 D P E F T X X X Z P V U V C F D P N , J B ' F B U V S F 7 J E F P T
Forward*/Reverse Parking Distance Warning (PDW) Video
QR CODE
A
REMINDERS:
•
If the vehicle is moving at speeds over 6 mph, the system may not activate
•
When more than t wo objects are sensed at the same time, the closest one will be recognized first
•
For ward*/Reverse Parking Distance Warning (PDW) is not a substitute for proper and safe backing-up procedures . Always drive safely and use caution when backing up . For ward*/Reverse Parking Distance Warning (PDW) may not detect ever y object behind or in front of the vehicle
Page 29 of 72
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED27
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
VIEW
P
For more information on Electronic Stability Control (ESC) and its specific features and operations, please refer to section 5 in the Owner’s Manual .
Electronic Stability Control (ESC)†5 / Traction Control System (TCS)†5
Electronic Stability Control (ESC) is designed to help stabilize the vehicle during certain cornering maneuvers
. Traction Control System (TCS) can help improve traction . It is a good idea to keep both ESC and TCS turned
on for daily driving whenever possible .
Press the ESC button A to turn Traction Control System OFF/ON .
To turn both Electronic Stability Control and Traction Control System OFF, press and hold the ESC button for more than 3 seconds . Press again to turn ON .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Stability Control Video
QR CODE
REMINDERS:
•
ESC is active by default at vehicle star t-up . When ignition is cycled, ESC will turn ON again
•
The ESC indicator light in the instrument cluster will be lit momentarily whenever ESC is activeA
Refer to section 4 in the Owner’s Manual for more information .
Instrument Cluster Control (Instrument Panel Dimmer)
With parking lights/headlights ON, press B (+) or (-) to adjust the brightness of the Instrument panel illumination .B
Refer to section 5 in the Owner’s Manual for more information .
Hill-start Assist Control (HAC)†5
Hill-start Assist Control (HAC) is designed to prevent the vehicle from rolling backwards when accelerating from a stop while on a steep incline .
HAC automatically activates whether ESC is OFF or ON but does NOT activate when ESC has malfunctioned .
REMINDERS:
•
HAC does not operate when the gear shift is in P (Park) or N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•
In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
•When HAC is active (e .g ., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator . HAC does not replace the need to apply brakes while stopped on an incline
•
HAC provides a t wo-second delay before the vehicle may star t rolling backwards
QUICK TIPS
DRIVER’S PANEL
DRIVER’S PANEL
Page 34 of 72
High Beam Assist (HBA)
*IF EQUIPPED32STINGER FEATURES & FUNCTIONS GUIDE
High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from other vehicles and road conditions .
To enable HBA , rotate the light switch to the AUTO Light position A and turn on the high beams by pushing the lever away from you . The High Beam Assist indicator will illuminate .
See section 4 in the Owner’s Manual for more information .
REMINDERS:
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions . Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams .
•
HBA will operate when vehicle speed exceeds 25 mph . When vehicle speed is below 15 mph, HBA will not turn on
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously . If the lever is pulled toward you while HBA is operational, HBA will turn off
•
If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•
DRL only operates during the day time
STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
High Beam Assist (HBA) Video
QR CODE
A
One-touch Lane Change Signal
To operate:
•Move lever up/down for right/left turn signal
•Slightly move lever up/down to activate one-touch lane change signal
Turn Signals
For more information on the User Settings Mode, please refer to your Owner’s Manual .
REMINDERS:
•
One-touch lane change signal is activated by briefly pressing the turn signal lever slightly for less than 1 second and then releasing . The lane change signal will blink 3 times
•
To change how many times the lane change signal blinks (3/5/7), go to User Set tings in the LCD instrument cluster modes
Page 35 of 72
STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED33
To operate:
•Move lever up/down to change wiper modes
–MIST: Single wipe
–OFF: Wiper off
–AUTO: Auto Rain Sensing
–LO: Slow wipe
–HI: Fast wipe
•
Pull to spray and wipe
Auto Rain Sensing
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO .
To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .
MIST
OFF
AUTO LOHIAUTO
Windshield Wipers & Washers
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Lifting Wipers / Wiper Service Mode Video
QR CODES
•
When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•
Set the wiper to the OFF position when the wiper is not in use
•
If going through a car wash, remind the at tendant to keep the vehicle in Neutral (N) and keep the engine running . Also, disable the Smar t Power Liftgate* lid control, turn off the auto rain sensing wipers and fold in the mirrors
•
Moving lever to HI increases Intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•
Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton down decreases frequency of wipes
QUICK TIPS
A
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace wiper blades or raise wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the service position B .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch to the MIST position C and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to normal position, turn the ignition ON, then activate MIST .See section 4 in the Owner’s Manual for more information .
B
C