2023 KIA CARNIVAL warning lights

*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 29
MIST: Single wipeOFF: Wiper offI N T: Intermittent wipeLO: Slow wipeHI: Fast wipe
MISTOFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
MIST OFF
AUTO
LO
HIHI
REARLO
OFF
HI: Fast wipeLO: Slow wipeOFF: Wiper off
OFFOFF
AUTO
OFFOFF
AUTO
*MMVTUSBUJPOT
BSF
GPS
EFNPOTUSBUJPO
QVSQPTFT
POMZ
"DUVBM
GFBUVSFT
PO
WFIJDMF
NBZ
WBS Z
3FGFS
UP
TFDUJPO

JO
UIF
0XOFS sT
.BOVBM
GPS
NPSF
JOGPSNBUJPO
Windshield Wipers & Washers
To operate:
•Move lever Up/Down to change wiper modes
•Press button B Up/Down to adjust Intermittent Wipe Speed
•Pull lever to spray and wipe
Rear Wiper & Washer
To operate:
•Rotate Rear Wiper switch to change Wiper modes
•Push to spray and wipe
Turn Signals & Fog Lights*
To operate:
•Turn Signals - Move lever Up/Down for Right/Left Turn Signal
•Fog Lights - Press switch A up/down to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for Fog Light operation.
The One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever slightly for less than 1 second and then releasing. The lane change signal will blink 3 times.
To change how many times (3/5/7) the Lane Change Signal blinks, go to the User
Settings Mode in the LCD Instrument Cluster modes.
STEERING WHEEL CONTROLS
•Pressing but ton B up increases Intermittent wipe frequency and wipe speed. Pressing the but ton down decreases the frequency of wipes
•Set the wiper to the OFF position when the wiper is not in use
QUICK TIPS
LO and HI sets the wiper speed. There is no intermit tent wipe function on the Rear Wipers
QUICK TIP
AB
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Lifting Wipers / Wiper Service Mode Video
QR CODE
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace wiper blades or raise wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the service position C to prevent damaging the hood.
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch (above) to the MIST position and hold the switch for more than two seconds until the wiper blade is in the fully up position.
To return wipers to normal position, turn the ignition ON, then activate MIST.
Refer to section 7 in the Owner ’s Manual for more information.
Refer to section 4 in the Owner ’s Manual for more information.
C
STEERING WHEEL CONTROLS

*IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 55
OTHER KEY FEATURES
HOLD
HOLDHOLD
HOLD
HOLDHOLD
HOLD
HOLDHOLD
HOLD
HOLD
HOLDHOLD
HOLD
HOLDHOLD
HOLD(But tons located on panel to the left of steering wheel)
HOLD
HOLDPOWER
DOOR OFFHOLD
HOLDHOLDPOWER
DOOR OFFHOLD
#VU UPOT
MPDBUFE
PO
DFOUFS
QJMMBST

Power Sliding Doors
Using the driver ’s panel controls, press the left/right Power Sliding Door buttons A, on the driver ’s panel controls, on the center pillars B or on the key fob C to automatically open/close the sliding doors.
REMINDER: If the POWER DOOR OFF but ton F is depressed, the Smar t Power Liftgate* will not operate.
Smart Key Auto Open/Close*: To automatically open and close the Power Liftgate / Sliding Doors, press and hold buttons D (close) and E (open) for more than 3 seconds.
Power Door OFF Button: When button F is ON (not depressed), the power sliding doors and power liftgate can be controlled with the buttons on the center pillar trim or liftgate B. Also, the doors will open/close automatically when pulling the handles from the inside or outside.
Smart Sliding Door with Auto Open
The sliding doors can be opened hands-free if the Smart Key is detected within the system range. The hazard warning lights will flash and a chime will sound two times and the door nearest the Smart Key will open. To activate the Smart Sliding Door with Auto Open, on some models, go the User Settings in
the Instrument Cluster and select Smart Liftgate. On other models, press the SETUP key on the audio head unit. Then press VEHICLE, DOOR and SMART SLIDING DOOR.
Passenger View* / Passenger Talk*
Passenger View, an in-cabin camera, helps the front passenger talk with rear passengers while viewing them on the audio head unit screen. On the head unit screen, press the Passenger View icon G.
Passenger Talk: Press the button H located on the overhead console to use the Passenger Talk, cabin intercom, function.
REMINDERS:
• The system will not operate when the Smar t Key is detected continuously near the vehicle after the doors are locked, or when a door is not locked or closed
•
Automatic stop and reversal will not activate in all situations
•
The auto-reverse feature is a supplemental feature and should never be relied upon as a primar y safet y device
•
To prevent injur y, make sure no body par ts are in the way of the sliding door when closing
•
Do not leave children or animals unat tended in the vehicle as they may operate the power sliding door in a manner that could result in injur y to themselves or others
•
If you are present but unable to quickly respond or at tend to children or animals in the vehicle, deactivate the power sliding door by pressing the POWER DOOR OFF but ton F on the driver ’s panel to the left of the steering wheel
Passenger
View
PassengerView
AAFBB
C
D
E
H
G
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Carnival Power/Smart Liftgate & Sliding Doors Video
QR CODE
Refer to section 4 in the Owner ’s Manual for more information.
OTHER KEY FEATURES

CA
D
E
F
G
•You can reprogram a single HomeLink® but ton by repeating Step 2
•Erasing the programmed but tons will delete all trained transmit ters
QUICK TIPS
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Homelink® Support Video
QR CODE
B
†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. 59
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will delete all information).
To program non-rolling and rolling code garage door openers and other devices:
1. Press and hold the left A and center C buttons simultaneously until the indicator light G begins to flash (to reprogram buttons, skip this step)
2. Press and hold the desired button A B C and hold the button on the transmitter while it is approximately 1 to 3 inches away from the mirror. The HomeLink®
Indicator light E will flash rapidly once the frequency signal has been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
3. Locate the “learn” or “smart ” button on the garage door ’s motor head unit. Press and release the button and complete Step 4 within 30 seconds
4. Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons.
Erasing programmed buttons:
Press and hold the A and C buttons simultaneously for approximately 20 seconds, and then release both buttons within 30 seconds.
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to reduce glare from a vehicle’s headlights located in the rear and also connect up to three electronic transmitters into one location.
HomeLink®†2 with Auto-Dimming Rearview Mirror*
A HomeLink® Channel 1
B HomeLink® Channel 2
C HomeLink® Channel 3
D Garage Door Opener Status Indicator: Closing or Closed
E HomeLink® Operation Indicator
F Garage Door Opener Status Indicator: Opening or Open
G HomeLink® User Interface Indicator
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink® Repeater Kit. For more information, go to w w w.HomeLink.com or call (800) 355-3515.
OTHER KEY FEATURES
OTHER KEY FEATURES