2023 JEEP RENEGADE clock

274 IN CASE OF EMERGENCY
3. Before raising the vehicle, use the wheel bolt
wrench to loosen, but not remove, the wheel
bolts on the wheel with the flat tire. Turn the
wheel bolts counterclockwise one turn while
the wheel is still on the ground.

Jacking Locations

4. Place the jack underneath the jacking location that

is closest to the flat tire. Jacking location
is indicated by a stamped arrow on the body.
Turn the jack screw clockwise to firmly engage
the jack saddle with the lift area of the sill
flange, centering the jack saddle inside the
cutout in the sill cladding.
NOTE:
Placement for the front and rear jacking locations
are c r
itical. See below images for proper jacking
locations.

Front Lifting Point
Front Jacking Location Rear Lifting Point
Rear Jacking Location

5. Raise the vehicle just enough to remove the flat

tire.
CAUTION!
Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the
Jacking Instructions for this vehicle.

IN CASE OF EMERGENCY 275
6. Remove the wheel bolts and tire.
7. M
ount the spare tire.

Mo
un
t

ing Spare Tire

NOTE:
Your vehicle may be equipped with a
compact spare tire or a limited — use spare
tire Ú page 333.
For vehicles so equipped, do not attempt to
install a center cap or wheel cover on the
compact spare.
8. Install the wheel bolts with the threaded end of the w

heel bolt toward the wheel. Lightly tighten
the wheel bolts.
9. Lower the vehicle to the ground by turning the jack

handle counterclockwise.
10. Finish tightening the wheel bolts. Push down on the
wrench while at the end of the handle
for increased leverage. Tighten the wheel bolts
in a star pattern until each wheel bolt has been
tightened twice Ú page 341. If in doubt about
the correct tightness, have them checked with
a torq u

e wrench by an authorized dealer or at
a service station. 11. After 25
mile
s (40 km) check the wheel bolt
torque
with a torque wrench to ensure that all
wheel bolts are properly seated against the
wheel.
12. Securely stow the jack, tools, chocks, and flat tire.

P

roperly Stowed Tire

WARNING!
Raising the vehicle higher than necessary can
make the vehicle less stable. It could slip off the
jack and hurt someone near it. Raise the vehicle
only enough to remove the tire.
CAUTION!
Be sure to mount the spare tire with the valve
stem facing outward. The vehicle could be
damaged if the spare tire is mounted incorrectly.WARNING!
To avoid the risk of forcing the vehicle off the
jack, do not fully tighten the wheel bolts until the
vehicle has been lowered. Failure to follow this
warning may result in serious injury.
WARNING!
A loose tire or jack thrown forward in a collision
or hard stop could endanger the occupants of
the vehicle. Always stow the jack parts and the
spare tire in the places provided. Have the
deflated (flat) tire repaired or replaced
immediately.
7

306 SERVICING AND MAINTENANCE
Removing Fuse Cover and Locking Screw

Fuse Panel & Cover Location
Proceed as follows:
Slowly turn the screw counterclockwise.
Slowly release the screw.
Remove the fuse cover by sliding it upward.
Mounting Fuse Cover and Locking Screw
Proceed as follows:
Properly secure the fuse cover to the box, slide
completely from top to bottom.
Fully depress the screw, using the special
screwdriver supplied.
Slowly turn the screw clockwise.
Release the screw.
1 — Mounting Screw
2 — Fuse Cover
CavityMaxi Fuse Cartridge Fuse Micro Fuse Description
* If Equipped
F01 70 Amp Tan ––Module Body Computer
F02 70 Amp Tan ––Module Body Computer, Rear Distribution Unit
F03 –20 Amp Blue –Controller Power Supply Body Computer
F04 –30 Amp Pink –Brake Control Electronics Module
F05 70 Amp Tan ––Electric Power-Assisted Steering
F06 70 Amp Tan ––Engine Cooling Fan
F08 –30 Amp Pink –Automatic Transmission, GSM
F09 ––5 Amp TanControl Module Engine

SERVICING AND MAINTENANCE 313
Replacing Exterior Bulbs
Headlamps
Hi/Lo Beam Light Halogen
See the following steps to replace:

1. O
pen the engine compartment and remove
the he a

dlamp bulb cap.

Headlamp Bulb Cap

2. Rotate the headlamp bulb socket counter -
clock w

ise then pull outwards.
Headlamp Bulb Socket

3. P ush on the locking tab on the headlamp bulb
conne c

tor and remove the bulb and socket.

Headlamp Bulb Headlamp Bulb

4. Install the new headlamp bulb making sure it is pr operly locked.
5. Install the headlamp bulb and socket; turn it clockw
ise making sure it is properly locked.
LED Headlamps – If Equipped
For replacement see an authorized dealer.
CAUTION!
During bulb replacement do not touch the new
glass bulb with your fingers. Oil contamination
will severely shorten bulb life. If the bulb comes
in contact with any oily surface, clean the bulb
with rubbing alcohol.
WARNING!
Carry out the operation of replacing lamps only
with the engine off. Also make sure that the
engine is cold, to avoid the danger of burns.
8

SERVICING AND MAINTENANCE 315
4. Rotate the bulb counterclockwise, and then
replace the bulb.
5. Insert the new bulb in the socket, making sure the b
ulb is locked into place.
6. Reconnect the electrical connector.
7. R ein

stall the access door.
LE D
F
r

ont Fog Lamps – If Equipped
For replacement see an authorized dealer.
Front Side Indicators
See the following steps to replace:

1. O perating from inside the engine
comp a

rtment using a suitable tool release
the retaining clip.

2. Remove lamp assembly by sliding it toward the outsi d

e.

Lamp Assembly
3. Remove the electrical connector by pushing
the t

ab then disconnect the electrical
connector.
4. Rotate counterclockwise to release the bulb socke t

from the lamp assembly, and remove it.

Bulb Socket
5. Remove the bulb from the socket.

Bulb

6 .

Insert the new bulb in the socket.
7. Rei
nstall the bulb and socket into the lamp
asse m

bly by turning it clockwise, making sure
it is locked into place.
8. Reconnect the electrical connector.
9. R ein

stall the lamp assembly on the car,
m a
ki
n

g sure it is locked into place.8

316 SERVICING AND MAINTENANCE
Side Indicators on External Rear View Mirrors – (If
Equipped)
See the following steps to replace:

1. Remove the mirror cap on the outside rear
view m

irror.

Mirror Cap Removing the mirror cap

2. Remove the transparent lens assembly as shown .

T

ransparent Lens
3. Remove the bulb socket and bulb from the
trans
parent lens assembly by rotating the
socket counterclockwise.

Transparent Lens Assembly

4. Remove the bulb from the bulb socket by pulli
ng the bulb straight out.
5. Insert the new bulb, making sure that it is locked
into place.
6. Reinstall the socket in to the transparent lens assem
bly.
7. Reinstall the cover on the outside rear view mirror
, making sure it is locked into place.
CAUTION!
The procedure is described as a guideline. For
the replacement of the lamp it is recommended
that you contact an authorized dealer.

318 SERVICING AND MAINTENANCE
7. Replace the bulb as necessary.

Rear Tail Lamp Holder

8. Insert the new bulb, making sure it is properly locke
d.
9. Reassemble the lamp assembly on the rear tail
lamp housing, tightening the screws.
10. Reposition the rear tail lamp on the car.
11. Se
cure the fastener of the rear tail lamp and
recon n

ect the electrical connector.
12. Reinstall the door making sure it locked into place
.
13. Finally close the liftgate. LED Re
ar Tail Lamps – If Equipped
For replacement see an authorized dealer.
Reverse Lights – If Equipped With LED Tail Lamps
See the following steps to replace:

1. U se a suitable tool to remove the screws and
remove

the access door.

Reverse Light Access
2. B
y pushing the electrical connector tab
remove
the electrical connector.

Reverse Light Assembly

3. R otate the bulb counterclockwise, and then
r e p
la

ce the bulb.
4. Insert the new bulb in the socket, making sure the b
ulb is locked into place.
5. Reconnect the electrical connector.
6. Rei
nstall the access door.
Cent e

r High Mounted Stop Lamp (CHMSL)
The CHMSL is LED. For replacement see an
a uthori

zed dealer.
1 — Tail Light
2 — Reverse Bulb
3 — Position Light/Stop Light/Turn Signal
1 — Screw
2 — Screw
3 — Access Door
1 — Bulb