2023 JEEP RENEGADE light

312 SERVICING AND MAINTENANCE
Front Position/Daytime Running Lights (DRL)/Front Turn Indicator PSY24W
Front Direction Indicator Lamps (If Equipped With LED Headlamps) PSY24W
Front Fog Lamps H11
Front Fog Lamps (LED Versions) LED (Serviced at an authorized dealer)
Side Indicators (Front And Side View Mirror) WY5W
Tail/Brake Lights/Turn Indicators (LED Versions) LED (Serviced at an authorized dealer)
Tail/Brake Lights/Turn Indicators P21W
Center High Mounted Stop Lamp (CHMSL) LED (Serviced at an authorized dealer)
Reverse W16W
License Plate Lamp W5W
Exterior Bulbs
Lamps Bulb Number

SERVICING AND MAINTENANCE 313
Replacing Exterior Bulbs
Headlamps
Hi/Lo Beam Light Halogen
See the following steps to replace:

1. O
pen the engine compartment and remove
the he a

dlamp bulb cap.

Headlamp Bulb Cap

2. Rotate the headlamp bulb socket counter -
clock w

ise then pull outwards.
Headlamp Bulb Socket

3. P ush on the locking tab on the headlamp bulb
conne c

tor and remove the bulb and socket.

Headlamp Bulb Headlamp Bulb

4. Install the new headlamp bulb making sure it is pr operly locked.
5. Install the headlamp bulb and socket; turn it clockw
ise making sure it is properly locked.
LED Headlamps – If Equipped
For replacement see an authorized dealer.
CAUTION!
During bulb replacement do not touch the new
glass bulb with your fingers. Oil contamination
will severely shorten bulb life. If the bulb comes
in contact with any oily surface, clean the bulb
with rubbing alcohol.
WARNING!
Carry out the operation of replacing lamps only
with the engine off. Also make sure that the
engine is cold, to avoid the danger of burns.
8

314 SERVICING AND MAINTENANCE
Position Lights/Daytime Running Lights/Fog
Lights
See the following steps to replace:

1. Turn the front wheels completely.

2. Us e

a suitable tool to remove the access door.

Posi t

ion Light/Daytime Running Light/Fog Light Access

3. Remove the electrical connector.
4. Re l

easing the two tabs, and remove the bulb
and b

ulb socket from the housing.
Position Light/Daytime Running Light Assembly

5. Install the new bulb and socket into the housi n

g, and engage the two tabs, making
sure that it is properly locked.
6. Reconnect the electrical connector.
7. Re i

nstall the access door.
Front

Fog Lights
See the following steps to replace:

1. T urn the front wheels completely.

2. Us e

a suitable tool to remove the access door.
Posi
t
ion Light/Daytime Running Light/Fog Light Access

3. By pushing the electrical connector tab remov e

the electrical connector.

Fog Light Assembly

1 — Screws
2 — Access Door
1 — Bulb Socket1 — Screws
2 — Access Door

SERVICING AND MAINTENANCE 317
Rear Tail Lamps
Contain the following:
Position Lights
Stop Lights
Direction Indicator
REVERSE Lights
See the following steps to replace:

1. O pen the liftgate.

2. Usi
ng a suitable tool remove the door as
shown .

T

rim Panel Door

3. Using a suitable tool remove fastener.
4. Di s

connect the electrical connector by pushing
the r

elease.
Rear Lamp Fastener and Electrical Connector

5. Remove the rear tail lamp, sliding it toward the outsi d

e as shown.

Tail Lamp Removal
6. Unscrew the screws and remove the rear tail
lamp
holder.

Rear Lamp Assembly

1 — Electrical Connector
2 — Fastener
1 — Mounting Screws
8

318 SERVICING AND MAINTENANCE
7. Replace the bulb as necessary.

Rear Tail Lamp Holder

8. Insert the new bulb, making sure it is properly locke
d.
9. Reassemble the lamp assembly on the rear tail
lamp housing, tightening the screws.
10. Reposition the rear tail lamp on the car.
11. Se
cure the fastener of the rear tail lamp and
recon n

ect the electrical connector.
12. Reinstall the door making sure it locked into place
.
13. Finally close the liftgate. LED Re
ar Tail Lamps – If Equipped
For replacement see an authorized dealer.
Reverse Lights – If Equipped With LED Tail Lamps
See the following steps to replace:

1. U se a suitable tool to remove the screws and
remove

the access door.

Reverse Light Access
2. B
y pushing the electrical connector tab
remove
the electrical connector.

Reverse Light Assembly

3. R otate the bulb counterclockwise, and then
r e p
la

ce the bulb.
4. Insert the new bulb in the socket, making sure the b
ulb is locked into place.
5. Reconnect the electrical connector.
6. Rei
nstall the access door.
Cent e

r High Mounted Stop Lamp (CHMSL)
The CHMSL is LED. For replacement see an
a uthori

zed dealer.
1 — Tail Light
2 — Reverse Bulb
3 — Position Light/Stop Light/Turn Signal
1 — Screw
2 — Screw
3 — Access Door
1 — Bulb

SERVICING AND MAINTENANCE 319
License Plate Lights
See the following steps to replace:

1. U
sing a suitable tool remove the license plate
lens.

L

icense Plate Light LocationLicense Plate Light

2. R emove the bulbs from the individual side
conta c

ts. 3. Insert the new bulbs, and ensure that they are
proper
ly locked between the contacts.
4. Reinstall the license plate lens.
NOTE:
If removing the license plate lens using a screw -
driver, be sure to cover the tip of the screwdriver
w ith a

cloth so no damage is done to the lenses or
the vehicle paint.
Replacing Interior Bulbs
Front Courtesy Light
See below steps to replace:

1. U sing a suitable tool remove the front
courte
sy light as shown.

Front Courtesy Light Housing

2. Release the retainer clips and bulb housing as shown .
F

ront Courtesy Bulb Housing

3. Replace the bulbs by pulling straight out of bulb

housing.

Front Courtesy Bulb Housing

1 — Retaining Clips
2 — Bulb Housing
8

320 SERVICING AND MAINTENANCE
4. Insert the new bulbs, making sure that they are
properly locked.
5. Reassemble the bulb housing and courtesy light

housing making sure that they are
properly locked.
6. Install the front courtesy light making sure that it is
properly locked.
Dome Light Vanity Mirror
See below steps to replace:

1. L ift the cover of the mirror and pull out the
visor m

irror light cover.

2. Replace the bulb, releasing it from the side contac
ts, and then insert the new bulb, making
sure that it is properly locked between the
contacts.

Visor
3. Reinstall the visor mirror light cover making
sure

that it is properly locked.
4. Finally lower the visor mirror cover to the mirror
.
Dome Light Glove Compartment
See below steps to replace:

1. O pen the glove compartment.

2. Pla
ce your fingers inside the light assembly,
pull

the bulb to replace it.

Bulb Removal/Installation

3. Insert the new bulb, making sure it is properly locke d

. Rear Dome Light — Without Retractable Roof
See below steps to replace:

1. U
sing a suitable tool release the lamp
asse m

bly at both the ends.

2. Open the flap and replace the bulb.

Rear
Dome Light Housing

3. Insert the new bulb, locking it between the conta c

ts.
4. Reinstall the dome light.
1 — V

isor Mirror Cover
2 — Visor Mirror Light
1 — Bulb
2 — Flap

SERVICING AND MAINTENANCE 321
Dome Light — MY SKY
See below steps to replace:

1. L
ower the handle in the direction shown
remove
the dome light.

Retractable Roof Light

2. Replace the bulb by removing it from the side conta c

ts.

Bulb
3. I
nsert the new bulb, locking it between the
c on t
a c

ts.
4. Reinstall the dome light.
Inter

ior Cargo Lights
See below steps to replace:

1. Open the luggage compartment and remove the d o

me light assembly.

2. Open the light cover and replace the bulb.

Light
Cover

3. Close the light cover over the bulb.
4. R ein

stall the dome light in its correct position.
WARNING!
Before proceeding with the replacement of
the lamp wait for the exhaust pipes are cool:
DANGER OF BURNS!
Modifications or repair of the electrical system
performed incorrectly and without taking into
account the technical characteristics can
cause malfunctions with the risk of fire.
Halogen lamps contain gas under pressure, in
the event of breakage be careful of the projec -
tion of fragments of glass.
Halogen lamps must be handled by touching
only the metallic part. If the transparent bulb
is in contact with the fingers, reduces the
intensity of the emitted light and you can also
affect the life of the lamp. In case of acci -
dental contact, rub the bulb with a cloth damp -
ened with alcohol and allow to dry.
8