2023 JEEP GLADIATOR ECU

70GETTING TO KNOW YOUR VEHICLE
The Locking Storage Bin can be removed by
unfastening the four bolts that attach the bin to the
vehicle floor using the provided #40 Torx head
driver and ratchet. The bottom of the storage bin
has rubber mats that need to be removed to
access the four bolts. These bolts can then be
stored in the fastener bin below the rear seat.

Under Seat Storage (Open View)

Your Locking Storage Bin also has a front handle
that makes it easier to carry and pull out from the
floor of the vehicle when the four bolts that attach
the bin to the floor are removed.
Rear Behind Seat Storage — If Equipped
The rear wall storage bin is located behind the right
rear seat.
Rear Wall Storage Bin

Rear Wall Storage Bin

To access the storage bin, pull upward on the pull
strap located on the upper outboard side of the
right rear seat, and fold the seatback forward.
NOTE:The rear seatback can be locked using the vehicle
key to secure items in the rear wall storage bin. The
seat lock is located on the upper outboard side of
each seatback. Both seatbacks should be locked
to limit access to items behind seat. Rear Wall Netting
The rear wall netting can be accessed the same
way as the rear wall storage bin.

Rear Wall Netting

Fastener Bin
Your vehicle is equipped with a Fastener Bin used
to store the fasteners for the doors, windshield,
and hard top (if equipped) while not in use. The
Fastener Bin is located behind the rear seat
storage bin. The Fastener Bin contains foam
inserts for each of the fasteners; they are
removable.
1 — Key Locks
2 — Removable Bolts
3 — Handle1 — Rear Wall Storage Bin
2 — Pull Strap

23_JT_OM_EN_USC_t.book Page 70

GETTING TO KNOW YOUR VEHICLE83
(Continued)
LOWERING THE SOFT TOP
Use this QR code to access your
digital experience. If the temperature is below 72°F (24°C) and/or
the top has been folded down for a period of time,
the top will appear to have shrunk when you raise
it, making it difficult to put up. This is caused by a
natural contraction of the vinyl or acrylic materials
of the fabric top.
Place the vehicle in a warm area. Pull steadily on
the top fabric. The vinyl will stretch back to its
original size and the top can then be installed. If
the temperature is 41°F (5°C) or below, do not
attempt to put the top down or roll the rear or side
curtains.
WARNING!
Do not drive the vehicle with the rear window
up/removed unless the quarter windows are
also removed. Dangerous exhaust gases
could enter the vehicle causing harm to the
driver and passengers.
The fabric quarter windows and fabric top are
designed only for protection against the
elements. Do not rely on them to contain occu -
pants within the vehicle or to protect against
injury during an accident. Remember, always
wear seat belts.
Make sure hands and fingers are clear of all
pinch points when installing and removing the
soft top. The lift assist mechanism and side
bows may cause serious injury if fingers or
hands get caught in between.
CAUTION!
The soft top is not designed to carry any
additional loads such as roof racks, spare tires,
building, hunting or camping supplies, and/or
luggage, etc. Also, it was not designed as a
structural member of the vehicle and, thus,
cannot properly carry any additional loads other
than environmental (rain, snow, etc.).
CAUTION!

Do not run a fabric top through an automatic
car wash. Window scratches and wax buildup
may result.

Do not lower the top when the temperature is
below 41°F (5°C). Damage to the top may
result.

Do not move your vehicle until the top has been
either fully attached to the windshield frame, or
fully lowered.
Follow the proper steps for cleaning and caring
for your vehicle’s fabric top
Ú
page 413.
Do not use any tools (screwdrivers, etc.) to pry
or force any of the clamps, clips, or retainers
securing the soft top. Do not force or pry the soft
top framework when opening or closing.
Damage to the top may result.

Failure to follow these cautions may cause interior
water damage, stains, or mildew on the top
material:

It is recommended that the top be free of water
prior to opening it. Operating the top, opening a
door or lowering a window while the top is wet
may allow water to drip into the vehicle's interior.

Careless handling and storage of the soft top
may damage the seals, causing water to leak
into the vehicle's interior.
The soft top must be positioned properly to
ensure sealing. Improper installation can cause
water to leak into the vehicle's interior.

CAUTION!
2

23_JT_OM_EN_USC_t.book Page 83

86GETTING TO KNOW YOUR VEHICLE
Lowering The Soft Top Into The Sunrider® Position:
Use this QR code to access your
digital experience.

1. Fold both sun visors forward against the windshield.

2. Release the header latches from the crossbar by pulling
the handle downward. Make
sure the hook is fully disengaged from its
receiver.

Step Two

3. From both the left and right sides, lift up on the #1 Bow of the soft top to begin the operation.
It is recommended to utilize two people for this
procedure.
Step Three

4. Move to the side of the vehicle and use the side link to fold the soft top rearward.

Step Four
5. Secure the top in this position by using the two
hook-and-loop fasteners provided in the
center console.

Step Five

NOTE:The vehicle can be driven in the Sunrider® Position
with the rear window and quarter panel cover
assemblies fully installed or completely removed.
CAUTION!
Quarter panel cover assemblies and rear
window must be either all in or all out.

23_JT_OM_EN_USC_t.book Page 86

GETTING TO KNOW YOUR VEHICLE89
2. Fold the divider upward, covering the rear window.

Step Two

3. Lay the first quarter panel cover assembly all the way to the right side and the second
quarter panel cover assembly on the left side.
Secure both using the two hook-and-loop
fastener straps on each side.
NOTE:The quarter panel cover assemblies are marked
“1” and “2” on the inside of the panel assembly.
Step Three

4. Close the storage bag and store in a safe location.

Step Four

RAISING THE SOFT TOP
Use this QR code to access your
digital experience.

1. From the Sunrider® Position, remove straps if previously
secured.

Step One

1 — Left Quarter Panel Cover Assembly
2 — Right Quarter Panel Cover Assembly
CAUTION!
Failure to follow the next steps could result in
damage to the soft top or vehicle.
2

23_JT_OM_EN_USC_t.book Page 89

GETTING TO KNOW YOUR VEHICLE91
2. Engage the plastic retainers on the front of the cover assembly (toward the front of the
vehicle) starting at the top, and working
downward.

Step Two

NOTE:It is critical that the retainers are fully engaged
before the vehicle resumes motion.
3. Secure the hook-and-loop fastener at the upper front corner of each quarter panel cover
assembly by pressing firmly.
Step Three

4. From either side, guide the rear window into the retainer while keeping the window level.

Step Four

5. Engage the retainer along the bottom of the rear window beginning on the left side of the
vehicle and working toward the center. Then,
move to the right side of the vehicle and continue from the center, working to the right
until the rear window is secured in the lower
retainer.

Step Five

6. Engage the vertical retainers up the right and left side of the rear window.

Step Six

2

23_JT_OM_EN_USC_t.book Page 91

GETTING TO KNOW YOUR VEHICLE93
INSTALLING THE SOFT TOP
NOTE:If installing the soft top immediately after removing
the hard top, ensure the wire harness is stored
properly, and not tucked under the belt rail
Úpage 98.

1. Install the belt rail on the rear of the vehicle. Secure the belt rail using the six fasteners
with the provided #T50 Torx head driver and
ratchet. Refer to the following table for
recommended torque specifications.
Step One

2. Install the door frames. Start with both front doors, followed by both rear doors. Apply the
appropriate torque specifications for the door
frame Torx head fasteners Ú page 104.3. Unsnap and remove the storage bag. This bag
should be discarded. It was intended as a
protective cover for shipping only.
4. Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top
onto the rear of the cab. Line up the locater
pins (one on each side of the soft top) with the
rear door frames.

Step Four

Torque
Specification For Torx
Fastener Maximum Minimum
119.5 in-lb (13.5 N·m) 150.5 in-lb
(17.0 N·m) 106.2 in-lb
(12.0 N·m)
CAUTION!
Do not overtighten Torx fasteners. Damage to
the retainers will occur.
1 — Corner Fasteners
2 — Rear Fasteners
CAUTION!
Failure to follow the next steps could result in
damage to the soft top or vehicle.
2

23_JT_OM_EN_USC_t.book Page 93

94GETTING TO KNOW YOUR VEHICLE
5. Using the provided #T50 Torx head driver and ratchet, install and tighten the Torx fasteners
by turning them clockwise. Secure them until
they are snug, being careful not to cross-
thread the fasteners or overtighten. Refer to
the following table for recommended torque
specifications. Repeat on the opposite side.

Step Five Step Five
6. Before driving the vehicle with the top in the
Sunrider® position, ensure the top is secured
with the provided hook-and-loop fasteners
Úpage 89.

Step Six

Torque
Specification For Torx
Fasteners Maximum Minimum
119.5 in-lb (13.5 N·m) 150.5 in-lb
(17.0 N·m) 106.2 in-lb
(12.0 N·m)
CAUTION!
Do not overtighten Torx fasteners. You can strip
the fasteners if they are overtightened.

23_JT_OM_EN_USC_t.book Page 94

98GETTING TO KNOW YOUR VEHICLE
4. Unfold the outer flap and zip the hard top bag closed.

Step Four

5. Store the Freedom Top panels bag in a safe location.
HARD TOP FRONT PANEL(S)
I
NSTALLATION

1. Set the right side panel on the windshield
frame with the locating pin in the front
receiver mounting hole, followed by the left
side panel, making sure there is no overhang.
Make sure that the panels are sitting flush
with the body.
2. Secure the panel(s) using the same steps for
removal in reverse order.
NOTE:To prevent water leaks, the seals and hard top
panels should be clear of any dust and debris prior
to reinstallation.
REMOVING THE HARD TOP
Use this QR code to access your
digital experience.

1. Remove both front panels

Ú
page 95.

2. Open both front doors.
3. Using the provided #50 Torx head driver and ratchet, remove the two Torx
head screws that secure the hard top at the
B-pillar (near the top of the front doors).
Step Three

4. If equipped, remove the lower interior soft trim panel (attached by the hook-and-loop
fastener) by pulling the panel away from the
trim.

Step Four

23_JT_OM_EN_USC_t.book Page 98