2023 INFINITI QX80 mirror controls

WAC0381X
1. Press and release the HomeLink®button
that you would like to program. The
HomeLink
®indicator light will flash in
orange slowly and “TRAINING” is dis-
played on the lower right of the mirror (if
not, refer to “Clearing the programmed
information” (P.2-90).).
2. Position the hand-held transmitter (gar- age door opener remote) 1-3 inches (2-8
cm) away from the HomeLink
®button
that you would light to program.
NOTE:
Some hand-held transmitter (garage
door opener remotes) may actually train
better at a distance of 6-12 inches (15-
20 cm). Keep this in mind if you have difficulty with the programming pro-
cess.
3. While the HomeLink
®indicator light is
flashing in orange, press and hold the
hand-held transmitter button. Continue
pressing the hand-held transmitter but-
ton until the HomeLink
®indicator light
changes from orange to green and
“TRAINED” is displayed on the lower
right of the mirror. You may now release
the hand-held transmitter button.
NOTE:
Some devices to be programmed may
require you to replace the Step 3 with
the cycling procedure noted in “Pro-
gramming HomeLink
®for Canadian cus-
tomers and gate openers” (P.2-89).
4. Wait until your garage door has stopped
moving before completing the next
steps.
5. Press the HomeLink
®button and ob-
serve the indicator light.
.If the indicator light remains constant green, your device should operate
when the HomeLink
®button is
pressed. At this point, if your device
operates, programming is complete.
.If the indicator light rapidly flashes in green, firmly press, hold for two
seconds and release the HomeLink
®
button up to three times to complete the programming process.
Do not
press the HomeLink
®button rapidly.
At this point if your device operates,
programming is complete. If the de-
vice does not operate or operates but
no door status indicator with Two-
Way Communication
*1, continue with
the next step of the programming
instructions.
6. At the garage door opener motor (se- curity gate motor, etc.), locate the
“Learn” or “Set” button. This can usually
be found where the hanging antenna
wire is attached to the motor-head unit
(see the device’s manual to identify this
button.). The name and color of the
button may vary by manufacturer.
NOTE:
A ladder and/or second person may
simplify the following steps. Do not
stand on your vehicle to perform the
next steps.
Instruments and controls2-87

2-88Instruments and controls
WAC0258X
Example
7. Firmly press and release the “Learn” or “Set” button until the indicator illumi-
nates. Once the button is pressed, you
have approximately 30 seconds to initi-
ate the next step.
8. Return to the vehicle and firmly press, hold for two seconds and release the
HomeLink
®button up to three times. Do
not press the HomeLink®button rapidly.
At this point programming is complete
and your device should operate when the
HomeLink
®button is pressed and re-
leased.
9. If you have any questions or are having difficulty programming your HomeLink
®
buttons, refer to the HomeLink®web
site at: www.homelink.com/infiniti or
call 1-800-355-3515.
*1: Programming Two-Way Communication
To check if your garage door opener is
compatible with this feature, refer to the
homelink.com/compatible/two-way-com-
munication website. If your garage door
opener has this functionality, HomeLink
®
mirror garage door status indicators may
appear after completion of programming.
NOTE:
It is possible for the HomeLink
®to stop
working with the garage door system
shortly after initial programming if the
Two-Way Communication programming is
not completed. If this is the case, following
the steps below will restore door operation.
1. In your vehicle, press and hold the trained HomeLink
®button for 2 seconds, then
release. Confirm that the garage door is
moving. When the garage door stops,
you will have one minute to complete the
following steps:
NOTE:
A ladder and/or second person may
simplify the following steps. Do not
stand on your vehicle to perform the
next steps. 2. On your garage door opener in your
garage, locate the “Learn” or “Set”
button (usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty locat-
ing this button, refer to the device’s
owner’s manual.
3. Press and release the “Learn” or “Set” button.
4. A light on your garage door opener may flash, and your two-way HomeLink
®
indicators in your vehicle may flash,
confirming completion of the process.
5. Pressing the trained HomeLink
®button
will now activate your garage door. The
status indicators will show when the
door is moving.
6. Your two-way enrollment is now com- plete.
USING THE GARAGE DOOR
TWO-WAY COMMUNICATION
HomeLink®has the function of communi-
cating with garage door opener systems. If
your garage door openers are compatible
with HomeLink
®, the HomeLink®can:
. receive and display “closing” or “opening”
status from your garage door opener.
. recall and display the garage door being
“closed” or “opened”.

2-90Instruments and controls
Step 3: While the HomeLink®indicator light
is flashing in orange, press and release
(“cycling”) the hand-held transmitter button
every 2 seconds. Continue to press and
release the hand-held transmitter button
until the HomeLink
®indicator light changes
from orange to green. When the indicator
light illuminates in green, hand-held trans-
mitter button may be released.
Proceed with “Programming HomeLink
®”
step 4 to complete.
Remember to plug the device back in when
programming is completed.
OPERATING THE HomeLink®
UNIVERSAL TRANSCEIVER
The HomeLink®Universal Transceiver, after
it is programmed, can be used to activate the
programmed device. To operate, firmly press
the appropriate programmed HomeLink
®
button. The indicator light will illuminate in
green with three parenthesison the
mirror while the signal is being transmitted.
PROGRAMMING TROUBLE-
SHOOTING
If the HomeLink®does not quickly learn the
hand-held transmitter information:
. replace the hand-held transmitter bat-
teries with new batteries. .
position the hand-held transmitter with
its battery area facing away from the
HomeLink
®button.
. press and hold the HomeLink®button
and hand-held transmitter button in
each step without interruption.
. position the hand-held transmitter 1 to 3
in (2 to 8 cm) away from the HomeLink
®
button. Hold the transmitter in that
position for up to 15 seconds. If
HomeLink
®is not programmed within
that time, try holding the transmitter in
another position - for example, 6 to 12 in
(15 to 30 cm) away, keeping the
HomeLink
®button in view at all times.
If you have any questions or are having
difficulty programming your HomeLink
®
buttons, refer to the HomeLink®web site
at: www.homelink.com/infiniti or 1-800-
355-3515.
CLEARING THE PROGRAMMED
INFORMATION
The following procedure clears the pro-
grammed information from three buttons.
Individual buttons cannot be cleared. How-
ever, individual buttons can be repro-
grammed, see “Reprogramming a single
HomeLink
®button” (P.2-90).
To clear all programming
1. Press and hold the two outer HomeLink®
buttons until the indicator light begins to
flash in green and “CLEARED” is dis-
played on the mirror, in approximately 10
seconds. Do not hold for longer than 20
seconds.
2. Release both buttons.
HomeLink
®is now in the programming mode
and can be programmed at any time begin-
ning with “Programming HomeLink
®” - Step
1.
REPROGRAMMING A SINGLE
HomeLink®BUTTON
To reprogram a HomeLink®button, com-
plete the following.
1. Press and hold the desired HomeLink
®
button. DO NOT release the button.
2. The indicator light will illuminate in green, and after 20 seconds it will begin
to flash in orange and “TRAINING” is
displayed on the mirror.
3. Release the HomeLink
®button and
proceed with “Programming
HomeLink
®” — Step 3.
For questions or comments, contact
HomeLink
®at: www.homelink.com/infiniti
or 1-800-355-3515.

JVS1142X
The LDW system will operate when the
vehicle is driven at speeds of approximately
37 MPH (60 km/h) and above, and the lane
markings are clearly visible on the road.
The LDW system monitors the lane markers
on the traveling lane using the camera unit
located above the inside mirror.
The LDW system warns the driver that the
vehicle is beginning to leave the driving lane
with an indicator and a steering wheel
vibration. (See “LDW system operation”
(P.5-24).)WAF0730X
LDW indicator (on the vehicle informa-
tion display)
Vehicle information display
Steering-wheel-mounted controls (left
side)
Warning systems switch
Starting and driving5-23