2023 HYUNDAI PALISADE drive modes

03
3-41
Rear Seat Belt – Passenger’s 3point
system with convertible locking
retractor
This type of seat belt combines the
features of both an emergency locking
retractor seat belt and an automatic
locking retractor seat belt. Convertible
retractor type seat belts are installed
in the rear seat positions to help
accommodate the installation of child
restraint systems. Although a convertible
retractor is also installed in the front
passenger seat position, NEVER place
any infant/child restraint system in the
front seat of the vehicle.
To fasten your seat belt:
Pull the seat belt out of the retractor
and insert the me
tal tab into the buckle.
There will be an audible “click” when
the tab locks into the buckle. When
not securing a child restraint, the seat
belt operates in the same way as the
driver’s seat belt (Emergency Locking
Retractor Type). It automatically adjusts
to the proper length only after the lap
belt portion of the seat belt is adjusted
manually so that it fits snugly across your
hips.
When the seat belt is fully extended from
the retractor to allow the installation of
a child restraint system, the seat belt
operation changes to allow the belt to
retract, but not to extend (Automatic
Locking Retractor Type). Refer to the
“Using a Child Restraint System” section
in this chapter.
B0059KO11
To release your seat belt:
Press the release button M in the locking
buckle.
When it is r

eleased, the belt should
automatically draw back into the
retractor. If this does not happen, check
the belt to be sure it is not twisted, then
try again.
NOTICE
Although the seat belt retractor
provides the same level of protection
for seated passengers in either
emergency or automatic locking
modes, the emergency locking mode
allows seated passengers to move
freely in their seat while keeping
some tension on the belt. During a
collision or sudden stop, the retractor
automatically locks the belt to help
restrain your body.
To deactivate the automatic locking
mode, unbuckle the seat belt and allow
the belt to fully retract.

Instrument Cluster4-32
Trip Computer (Type A)
The trip computer is a microcomputer-
controlled driver information system that
displays information related to driving.
Information
Some driving information stored in the
trip computer (for example, Average
Vehicle Speed) resets if the battery is
disconnected.
Trip modes
Drive Info

[ Trip distance

[ Total driving time

[ Average fuel economy
Since refueling

[ Trip distance

[ Total driving time

[ Average fuel economy
Accumulated Info

[ Trip distance

[ Total driving time

[ Average fuel economy
Auto Stop (if equipped)
B0090KO01
To change the trip mode, toggle the
", " switch on the steering wheel

[ Manual reset
To clear the average fuel economy
manually, press the OK switch on the
steering wheel for more than 1 second
when the Average Fuel Economy is
displayed.

[ Automatic reset
To automatically reset the average
fuel economy, select between ‘After
Ignition’ or ‘After Refueling’ from
the Settings menu in the instrument
cluster.

- After Ignition: When the engine has
been OFF for 3 minutes or longer
the average fuel economy will reset
automatically.
- After Refueling: The average fuel economy will reset automatically
after adding 6 liters (1.6 gallons) of
fuel or more and after driving speed
exceeds 1 mph (1 km/h).

à For 10.25-inch instrument cluster, you
can check the fuel economy in the
center bottom of the cluster.

Instrument Cluster4-34
Trip Computer (Type B)
The trip computer is a microcomputer-
controlled driver information system that
displays information related to driving.
Information
Some driving information stored in the
trip computer (for example, Average
Vehicle Speed) resets if the battery is
disconnected.
Trip modes
Drive Info

[ Trip distance

[ Total driving time

[ Average fuel economy

Since refueling

[ Trip distance

[ Total driving time

[ Average fuel economy

Accumulated Info

[ Trip distance

[ Total driving time

[ Average fuel economy

Auto Stop (if equipped)

Digital speedometer
B0090KO01
To change the trip mode, toggle the
", " switch on the steering wheel

[ Manual reset
To clear the average fuel economy
manually, press the OK switch on the
steering wheel for more than 1 second
when the Average Fuel Economy is
displayed.

[ Automatic reset
To automatically reset the average
fuel economy, select between ‘After
Ignition’ or ‘After Refueling’ from
the Settings menu in the instrument
cluster.

- After Ignition: When the engine has
been OFF for 3 minutes or longer
the average fuel economy will reset
automatically.
- After Refueling: The average fuel economy will reset automatically
after adding 1.6 gallons (6 liters) of
fuel or more and after driving speed
exceeds 1 mph (1 km/h).

à For 10.25-inch instrument cluster, you
can check the fuel economy in the
center bottom of the cluster.

05
5-129
Automatic Temperature Control
Mode
The Automatic Climate Control System
is controlled by setting the desired
temperature.
For your convenience and to improve the
efficiency of the climate control, use the
AUTO button and set the temperature to
72°F (22°C).
B0203EC01
1. Press the AUTO button O.
The modes, fan speeds, air intake and
air-conditioning will be controlled
automatically by the temperature setting
you select.
B0203EC02
A: Driver side, B: Passenger side
2. To select a different set point, turn
the temperature control knob to
the desired temperature. If the
temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
After the interior has cooled
sufficiently, adjust the knob to
a higher temperature set point
whenever possible.
To turn the automatic operation off,
select any button of the following:

- Mode selection button

- Front windshield defroster button
(Press the button one more time
to deselect the front windshield
defroster function. The ‘AUTO’ sign
will illuminate on the information
display once again.)

- Fan speed control button

- A/C button
The selected function will be controlled
manually while other functions operate
automatically.
B0203KO03
NOTICE
Never place anything near the ambient
light/solar sensor to ensure better
control of the heating and cooling
system.

06
6-59

[The driving mode automatically
changes to SMART SPORT, when
you abruptly accelerate the vehicle
or repetitively operate the steering
wheel (Your driving is categorized
to be sporty.). In this mode, your
vehicle drives in a lower gear for
abrupt accelerating or decelerating
and increases the engine brake
performance.
For general description of SMART ECO,
SMART COMFORT, and SMART SPORT
modes, refer to “ECO, COMFORT, SPORT
mode features”.
Limitation of SMART mode
SMART may be limited in following
situations. ECO, COMFORT, SPORT mode
features

[ The driver is using the paddle shifter
to manually shift gear. (The system
prioritizes the driver’s manual shifting)

[ Smart Cruise Control is activated.

[ The transmission oil temperature is
either extremely low or extremely
high.
Information

[When you mildly drive the vehicle
in SMART mode, the driving mode
changes to ECO mode to improve fuel
efficiency. However, the actual fuel
efficiency may differ depending on your
driving situations such as slope angle,
and vehicle speed.

[ When you dynamically drive the
vehicle in SMART mode by abruptly
decelerating or sharply curving, the
driving mode changes to SPORT mode.
However, it may adversely affect fuel
economy.
Multi Terrain Mode (AWD, if
equipped)
Multi terrain mode may be selected
according to the driver's preference or
road condition.
B1001KO08
Press the DRIVE/TERRAIN button to
change from Drive mode to Multi terrain
mode. After the button is pressed, rotate
the knob within 4 seconds to select
SNOW, MUD or SAND. When the DRIVE/
TERRAIN button is pressed again, the
previous Drive mode will be reselected.
B1003EU01For more details on Terrain mode, referto
“All Wheel Drive” section in thischapter.

Driver Assistance System7-74
Turning off Smart Cruise Control
B0328KO01
Press the Driving Assist () button to
turn Smart Cruise Control off.
Information
If your vehicle is equipped with Manual Speed
Limit Assist, press and hold the Driving Assist
(
) button to turn off Smart Cruise Control.
However Manual Speed Limit Assist will turn on.
CAUTION
Do not use the switches and buttons
at the same time. Smart Cruise Control
may not operate properly.
Display and Control
Basic function
You can see the status of the Smart
Cruise Con
trol operation in the Driving
Assist view on the cluster. Refer to “View
Modes” section in chapter 4.
Smart Cruise Control will be displayed
as below depending on the status of the
function.
B0348EU01
A: Operating, B: Temporarily canceled

[When operating
(1) Whether there is a vehicle ahead and the selected distance level
(2) Set speed
(3) Whether there is a vehicle ahead and the target vehicle distance

[ When temporarily canceled
(1) Your vehicle (shaded)
(2) Previous set speed (shaded)
(3) Whether there is a vehicle ahead (shaded) (if equipped)

Driver Assistance System7-100
Highway Driving Assist
Operation
Basic function
Displaying operating status
You can see the status of the Highway
Driving Assis
t operation in the Driving
Assist view on the cluster. Refer to “View
Modes” section in chapter 4.
Highway Driving Assist will be displayed
as below depending on the status of the
function.
B360EU01
A: Operating state, B: Standby state
(1) Highway Driving Assist indicator,
whether there is a vehicle ahead and
the selected distance level

à Highway Driving Assist indicator
- Green
: Operating state

-Grey
: Ready state
- White blink: Accelerator
depressed state
(2) Set speed
(3) Lane Following Assist indicator
(4) Whether there is a vehicle ahead and the selected headway
(5) Whether the lane is detected or not
Information

[ For more details on the display refer
to “Smart Cruise Control (SCC)” and
“Lane Following Assist (LFA)” sections
in this chapter.

[ The images and colors in the
instrument cluster may differ
depending on the cluster type or theme
selected from the settings menu.
Highway Driving Assist operation
Highway Driving Assist operates when:

[ Driving on the main r

oad of highways,
and turning on Highway Driving Assist
by pressing the Driving Assist button.

[ Entering the main road of highways
while Lane Following assist and Smart
Cruise Control are operating

07
7-103
Information

[Driving Speed Limit helps you drive
below 40 mph (60 km/h). At this time,
the vehicle decelerates due to the
vehicle ahead. After the vehicle has
decelerated, it cannot automatically
accelerate.

[ Driving Speed Limit will cancel in the
following circumstances:
- When the driver grabs the steering
wheel again
- When the driver turns on Lane
Following Assist by pressing the Lane
Driving Assist button
- When +, -,
switch or button is
operated,, or the accelerator pedal or
the brake pedal is depressed
Highway Lane Change Assist (if
equipped)
Displaying operating status
You can see the status of the Highway
Lane Change Assis
t function operation in
the Driving Assist view on the cluster. Refer
to “View Modes” section in chapter 4.
Highway Lane Change Assist function
will be displayed as below depending on
the status of the function.
B360EU04
A: Ready/Operating, B: Standby/Canceled
(1) Highway Lane Change Assist
indicator

[Green
on : Ready state

[ Green
blink : Operating state

[ Grey
on : Standby state

[ White
blink : Canceled state
(2) Green lane line
The lane line is displayed same as the
Highway Lane Change Assist indicator
(1). However, if the function is on
standby, it displays whether the lane
line is detected.
(3) Green arrow and shade The green arrow is displayed when a
certain amount of time has passed
after the function has started
operating, and until the lane change
has completed.