2023 HYUNDAI PALISADE ECO mode
[x] Cancel search: ECO modePage 159 of 661
Convenience Features5-10
Note that if you press the outside door
handle to lock the doors using the touch
sensor, the doors will not lock under the
following circumstances:
[ The Smart Key is in the vehicle
[ The Engine Start/Stop button is in the
ACC or ON position
[ Any of the doors are open (except for
the liftgate)
If this occurs, then a chime will sound
for about 3 seconds. Check the vehicle
before attempting to lock the car again.
CAUTION
Before you leave your vehicle with the
Smart Key, verify that your vehicle is
locked. When using the touch sensor
on the front door handle, listen to hear
that the lock has actuated, and then
pull the handle within 3 seconds to
confirm the doors are locked.
(If it has been longer than 3 seconds,
verify the doors are locked by pressing
the lock button on the Smart Key. You
will hear a single beep.)
WARNING
Do not leave the Smart Key in
your vehicle with children that are
unattended or unsupervised.
Children could inadvertently press
the Engine Start/Stop button or could
operate the power windows or other
vehicle controls or even cause the
vehicle to move. This could result in
serious injury or death.
Unlocking your vehicle (Button type)
B0097KO01
1. Have the smart key with you.
2. Press the door handle button or press the Door Lock button N on the smart
key to unlock the doors. The chime
sounds and hazard warning lights
blink two times.
If you unlock the doors using the
passenger side door handle, all the
doors are unlocked. If you unlock
the doors using the driver side door
handle, either the driver's side door is
unlocked or all the doors are unlocked
depending on the setting for the Two
Press Unlock feature.
Information
[ Change the Driver Door unlock mode
by referring to "Setting the Two Press
Unlock feature".
[ The door handle button or touch sensor
only operates when the smart key is
within 28-40 inches (0.7-1 m) from the
outside door handle.
[ If you do not open the door after
unlocking within 30 seconds, it returns
to the lock mode.
Page 160 of 661
05
5-11
Unlocking your vehicle (Touch
sensor type)
B0097EU03
1. Have the smart key with you.
2. Press the Door Unlock button N on the Smart Key or simply Grab the door
handle inside portion to activate the
unlock door touch sensor to unlock
the doors. The chime sounds and
hazard warning lights blink two times.
If you unlock the doors using the
passenger side door handle, all the
doors are unlocked. If you unlock
the doors using the driver side door
handle, either the driver's side door is
unlocked or all the doors are unlocked
depending on the setting for the Two
Press Unlock feature.
Information
[ Change the Driver Door unlock mode
by referring to User Settings.
[ The door handle button or touch sensor
only operates when the smart key is
within 28-40 inches (0.7-1 m) from the
outside door handle.
[ If you do not open the door after
unlocking within 30 seconds, it returns
to the lock mode.
[ If you unlock the door with the door
handle, the doors cannot be locked with
the touch sensor within 2 seconds. To prevent unintentional door lock or
unlock:
Press the lock button on the smart key
and immedia
tely press the unlock button
along with the lock button for more than
4 seconds. The hazard warning lights will
blink four times. At this time, the doors
will not lock or unlock even though the
touch sensor is touched on the outside
door handle.
To deactivate the function, press the
door lock or unlock button on the smart
key.
Setting the Two Press Unlock feature
You can activate or deactivate the Two
Pr
ess Unlock feature from the Settings
menu in the infotainment system.
Select:
- 6 H W X S
Page 162 of 661
05
5-13
Information
[ Laws in your country may restrict the
use of remote start. You should check
country regulations before using this
remote starting system.
[ The vehicle must be in P (Park) for the
remote start function to start.
[ The engine turns off if you get on the
vehicle without a registered smart key.
[ The engine turns off if you do not get
on the vehicle within 10 minutes after
remotely starting the vehicle.
[ The Remote Start button may not
operate if the smart key is not within 32
feet (10 m).
[ The vehicle will not remotely start if the
engine hood or liftgate is opened.
[ Do not idle the engine for a long period.
[ The Remote start function works the
same as Blue Link remote start. For
further caution information, refer to
the separately supplied “Blue Link
(Infotainment system) manual”.
Remote Smart Parking Assist
Feature (if equipped)
Some models are equipped with Remote
Smart Parking Assist Feature. With the
Smart Key, the vehicle can be moved
forward or backward remotely to enter or
exit a tight parking space.
For more details, refer to “Remote Smart
Parking Assist (RSPA)” section in chapter
7.
Panic alarm
The horn sounds and the hazard warning
lights blink for about 30 seconds if this
button is pressed for more than 1 second
To stop the horn and lights, press any
button on the transmitter.
Page 163 of 661
Convenience Features5-14
Start-up (if equipped)
Some models are equipped with a push
button start instead of a key cylinder.
You can leave your Smart Key in your
pocket or purse when you start your
vehicle.
For more details, refer to the “Engine
Start/Stop Button” section in chapter 6.
Information
Preventing the doors/liftgate from locking/
unlocking
[ Activating the feature
With the engine off, press the
lock button on the smart key and
immediately press the unlock button
along with the lock button for more
than 4 seconds. When the feature is
activated, the hazard warning lights
will blink four times.
[ How the feature works
When the feature is activated, the
doors or liftgate will not lock or unlock
even though the outside door handle
button or liftgate handle release switch
is pressed with the smart key in your
possession. Also, Welcome System
(if equipped) and Smart Liftgate (if
equipped) will not operate even though
you approach the vehicle with the
smart key.
[ Deactivating the feature
Press the door lock or unlock button
on the smart key, the feature will
deactivate.
Information
If the smart key is not moved for some
time, the detection function for smart key
operation will pause. Lift the smart key to
activate the detection again.
NOTICE
To prevent damaging the smart key:
[ Keep the smart key in a cool,
dry place to avoid damage or
malfunction. Exposure to moisture
or high temperature may cause
the internal circuit of the smart key
to malfunction which may not be
covered under warranty.
[ Avoid dropping or throwing the
smart key.
[ Protect the smart key from extreme
temperatures.
Page 198 of 661
05
5-49
Automatic-Dimming Night Vision Safety™
(NVS®) Mirror (if equipped)
The NVS® Mirror automatically helps
r
educe glare by monitoring light levels in
the front and the rear of the vehicle. Any
object that obstructs either light sensor
will degrade the automatic dimming
control feature.
) R U P R U H L Q I R U P D W L R Q U H J D U G L Q J 1 9 6 p
mirrors and other applications, please
refer to the Gentex website:
www.gentex.com
Your mirror will automatically dim
upon detecting glare from the vehicles
traveling behind you.
The mirror defaults to the ON position
each time the vehicle is started.
Integrated HomeLink
® Wireless Control
System
The HomeLink® Wireless Control System
pr
ovides a convenient way to replace
up to three hand held radio-frequency
transmitters used to activate compatible
devices such as gate operators, garage
door openers, entry door locks, security
systems, and home lighting.
NOTICE
+ R P H / L Q N p R S H U D W H V Z K L O H W K H L J Q L W L R Q
switch or Engine Start/Stop button is
in the ACC or ON position for safety
reasons. It is to prevent unintentional
security problems from happening
when the vehicle is parked outside the
garage.
WARNING
% H I R U H S U R J U D P P L Q J + R P H / L Q N p W R D
garage door opener or gate operator,
make sure people and objects are out
of the way of the device to prevent
potential harm or damage. Do not
X V H W K H + R P H / L Q N p Z L W K D Q \ J D U D J H
door opener that lacks the safety
stop and reverse features required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an
object - signaling the door to stop and
reverse - does not meet current U.S.
federal safety standards. Using a garage
door opener without these features
increases the risk of serious injury or
death.
) R U P R U H L Q I R U P D W L R Q F R Q W D F W
+ R P H / L Q N p D W Z Z Z K R P H O L Q N F R P R U
call Home-Link customer support at
1-800-355-3515.
It is also recommended that a new
battery be replaced in the handheld
transmitter of the device being trained
W R + R P H / L Q N p I R U T X L F N H U W U D L Q L Q J D Q G
accurate transmission of the radio
frequency.
1. Programming HomeLink
®
The following steps show how to
program HomeLink. If you have any
questions or are having difficulty
programming your HomeLink buttons,
refer to the HomeLink website or call the
HomeLink customer support toll-free
number. Do this, before going back to
the dealer who sold you the car.
Page 199 of 661
Convenience Features5-50
[ Visit the HomeLink website at: www.
homelink.com. Then at the top of the
page, choose your vehicle make. Then
watch the You Tube video, and/or
access additional website information.
[ If you choose to access the website
via your cell phone, scan the QR code.
[ Or, call HomeLink customer support
at 1-800-355-3515 (Please have the
vehicle make/model AND the opener
device make/model readily available.)
1) Programming Preparation
B0135EU04
1. When programming a garage door
opener, it is advised to park the
vehicle outside of the garage. 2. It is recommended that a new battery
be placed in the handheld transmitter
of the device being programmed to
HomeLink for quicker training and
accurate transmission of the radio-
frequency signal.
3. Place the ignition switch to the ACC (Accessory) position for programming
of HomeLink.
3 U R J U D P P L Q J D 1 H Z + R P H / L Q N p
B0135EU05
1. Press and release the HomeLink button (1), (2) or (3), you would like
to program. The HomeLink indicator
light (7) will flash orange slowly (if
not, perform the steps of “Erasing
HomeLink Buttons” section, and start
over).
B0135EU06
2. Position the garage door opener remote 1–3 inches (2–8 cm) away from
the HoleLink buttons.
Page 208 of 661
05
5-59
Reverse Parking Aid (if equipped)
B0136EU02
When the gear is shifted to the R
(Reverse) position, the side view mirror(s)
will rotate downwards to aid with driving
in reverse.
The state of the side view mirror button
M determines whether or not the mirrors
will move:
How it works
[ When the L or R switch M is selected
both side view mirrors will move.
[ If the L and R switch M are not
selected both outer side view mirrors
will not move.
The side view mirrors will automatically
revert to their original positions if any of
the following occur:
[ The ignition switch is placed to either
the LOCK/OFF position or the ACC
position.
[ The gear is shifted to any position
except R (Reverse).
[ The side view mirror adjustment
button is not selected.
Reverse parking aid user settings
mode
You may change the angle of the side
view mirror if it is difficult to see the rear
view with the basic downward mirror
angle provided when reversing.
When the vehicle is first delivered, the
set downward angle of the left and right
side view mirror are different to ensure
driver visibility.
1. Make sure the vehicle is stopped.
2. Depress the brake pedal and shift
the gear to R (Reverse). When L (Left)
or R (Right) switch is selected, both
side view mirror angle will move
downward to the basic set position.
3. Operate either L or R switch to select the side view mirror you would like
to adjust. Then press “z, x, {, y”
switch to adjust the side view mirror
to the desired angle.
4. After adjusting the angle to save the adjusted side view mirror angle, shift
the gear to another position other
than R (Reverse), or change the L and
R buttons to the neutral position (L
and R switchs are not pressed).
5. Set the opposite side view mirror following the above procedure 1 to 4.
Resetting reverse parking aid user settings
mode
To change the side view mirror angle
back t
o the basic angle, shift the gear to
R (Reverse), and adjust the mirror angle
higher than when the gear is in P (Park),
N (Neutral) and D (Drive).
NOTICE
When changing the angle of both side
view mirrors, it is recommended to
change the angle one side at a time
following the procedure 1 to 4.
Page 211 of 661
Convenience Features5-62
Adjusting the mirror height
B0913EU03
The height of the rearview mirror can be
adjusted to suit your driving posture.
Change to optical mirror mode, adjusting
the rearview mirror angle by moving it up
and down.
Display settings (Digital mirror
mode)
B0913EU01
1. Press the menu button M. The icons will be displayed.
Icons Settings
Select to adjust the brightness
of the display.
Select to adjust the display
up/down.
2. Press the menu button M repeatedly
and select the item you want to
adjust.
3. Press the button N or button O to change the setting.
The icons will disappear if the button
is not operated for approximately 5
seconds or more.
à If the brightness of the Digital Center
Mirror is set too high, it may cause eye
strain.
Adjust the Digital Center Mirror to
and appropriate brightness. If your
eyes become tired, change to optical
mirror mode.