2023 HYUNDAI IONIQ 6 brake light
[x] Cancel search: brake lightPage 559 of 582
9
9-43
Light Bulbs
Consult an authorized HYUNDAI dealer to
replace most vehicle light bulbs. It is
difficult to replace vehicle light bulbs
because other parts of the vehicle must
be removed before you can get to the
bulb. This is especially true for removing
the headlight assembly to get to the
bulb(s).
Removing/installing the headlight
assembly can result in damage to the
vehicle.
WARNING • Prior to replacing a light bulb, depress the brake pedal, shift to P (Park), apply
the parking brake, press the Start/Stop
button to the OFF position, and take the
key with you when leaving the vehicle
to avoid sudden movement of the
vehicle and to prevent possible electric
shock.
• Be aware the bulbs may be hot and may burn your fingers.
NOTICE % H V X U H W R U H S O D F H W K H E X U Q H G R X W E X O E
Z L W K R Q H R I W K H V D P H Z D W W D J H W R S U H Y H Q W
G D P D J H W R W K H I X V H R U H O H F W U L F D O Z L U L Q J
V \ V W H P
NOTICE 7 R S U H Y H Q W G D P D J H G R Q R W F O H D Q W K H
K H D G O L J K W O H Q V Z L W K F K H P L F D O V R O Y H Q W V R U
V W U R Q J G H W H U J H Q W V
Information Headlight desiccant
This vehicle is equipped with desiccant to
reduce fogging inside the headlight due to
moisture. The desiccant is consumable and its performance may change based on the used
period or environment. If fogging inside the
headlight due to moisture continues for a long
time, contact an authorized HYUNDAI
dealer.
Information The headlight and tail light lenses could
appear to have condensation inside if the
vehicle is washed after driving or if the
vehicle is driven in wet weather. This
condition is caused by a higher temperature
inside the light and a cooler outside
temperature. Moisture that condenses in the
light is removed after driving with the light
on. If the moisture is not removed, contact an
authorized HYUNDAI dealer.
Information • A normally functioning light may flicker
momentarily to stabilize the vehicle’s
electrical control system. However, if the
light goes out after flickering momentarily,
or continues to flicker, have the system
inspected by an authorized HYUNDAI
dealer.
• The parking light may not turn on when the parking light switch is turned on, but the
parking light and headlight switch may turn
on when the headlight switch is turned on.
This may be caused by network failure or
vehicle electrical control system
malfunction. If this occurs, contact an
authorized HYUNDAI dealer.
Information Adjust the headlight aim after an accident or
the headlight is replaced.
Hyundai_CE_en_US.book Page 43
Page 563 of 582
9
9-47
Appearance Care
Exterior Care
NOTICE If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such as a
bumper, spoiler, garnish, light or side
view mirror might be damaged due to
sunlight reflected from the sign or
building. To prevent damage of the
exterior plastic parts, you should avoid
parking in areas where light may be
reflected or use a car cover. (The exterior
plastic parts applied to your vehicle may
vary.)
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Washing
To help protect your vehicle’s finish from
rust and deterioration, wash it thoroughly
and frequently at least once a month with
lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges of
the doors and rocker panels are kept clear
and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
High-pressure washing
• When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or its surrounding area directly with a high
pressure washer. Shock applied from
high pressure water may cause the
device to not operate normally.
• Do not bring the nozzle tip close to boots (rubber or plastic covers) or
connectors as they may be damaged if
they come into contact with high
pressure water.
WARNING After washing the vehicle, test the brakes
while driving slowly to see if they have
been affected by water before getting on
the road. If braking performance is
impaired, dry the brakes by applying
them lightly while maintaining a slow
forward speed.
NOTICE [ ' R Q R W X V H V W U R Q J V R D S F K H P L F D O G H W H U J H Q W V R U K R W Z D W H U D Q G G R Q R W
Z D V K W K H Y H K L F O H L Q G L U H F W V X Q O L J K W R U
Z K H Q W K H E R G \ R I W K H Y H K L F O H L V Z D U P
[ % H F D U H I X O Z K H Q Z D V K L Q J W K H V L G H Z L Q G R Z V R I \ R X U Y H K L F O H
[ ( V S H F L D O O \ Z L W K K L J K S U H V V X U H Z D W H U Z D W H U P D \ O H D N W K U R X J K W K H Z L Q G R Z V
D Q G Z H W W K H L Q W H U L R U
Hyundai_CE_en_US.book Page 47
Page 565 of 582
9
9-49
Finish damage repair
Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly rust
and may develop into a major repair
expense.
NOTICE , I \ R X U Y H K L F O H L V G D P D J H G D Q G U H T X L U H V
D Q \ P H W D O U H S D L U R U U H S O D F H P H Q W E H V X U H
W K H E R G \ V K R S D S S O L H V D Q W L F R U U R V L R Q
P D W H U L D O V W R W K H S D U W V U H S D L U H G R U
U H S O D F H G
NOTICE 0 D W W H S D L Q W I L Q L V K Y H K L F O H L I H T X L S S H G \f
, Q F D V H R I P D W W H S D L Q W I L Q L V K Y H K L F O H V L W L V
L P S R V V L E O H W R P R G L I \ R Q O \ W K H G D P D J H G
D U H D D Q G U H S D L U R I W K H Z K R O H S D U W L V
Q H F H V V D U \ , I W K H Y H K L F O H L V G D P D J H G D Q G
S D L Q W L Q J L V U H T X L U H G K D Y H \ R X U Y H K L F O H
P D L Q W D L Q H G D Q G U H S D L U H G E \ D Q D X W K R U L ] H G
+ < 8 1 ' $ , G H D O H U 7 D N H H [ W U H P H F D U H D V L W
L V G L I I L F X O W W R U H V W R U H W K H T X D O L W \ D I W H U W K H
U H S D L U
Bright-metal maintenance
• To remove road tar and insects, use a tar remover, not a scraper or other
sharp object.
• To protect the surfaces of bright metal parts from corrosion, apply a coating of
wax or chrome preservative and rub to
a high luster.
• During winter weather or in coastal areas, cover the bright metal parts with
a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.
Underbody maintenance
Corrosive materials used for ice and snow
removal and dust control may collect on
the underbody. If these materials are not
removed, accelerated rusting can occur
on underbody parts such as the frame and
floor pan, even though they have been
treated with rust protection.
Thoroughly flush the vehicle underbody
and wheel openings with lukewarm or
cold water once a month, after off-road
driving and at the end of each winter. Pay
special attention to these areas because it
is difficult to see all the mud and dirt. It
will do more harm than good to wet down
the road grime without removing it. The
lower edges of doors, rocker panels, and
frame members have drain holes that
should not be allowed to clog with dirt;
trapped water in these areas can cause
rusting.
WARNING After washing the vehicle, test the brakes
while driving slowly to see if they have
been affected by water. If braking
performance is impaired, dry the brakes
by applying them lightly while
maintaining a slow forward speed.
Aluminum wheel maintenance
The aluminum wheels are coated with a
clear protective finish.
• Do not use abrasive cleaner, polishing compound, solvent, or wire brushes on
aluminum wheels.
• Clean the wheel when it has cooled.
• Use only a mild soap or neutral detergent, and rinse thoroughly with
water. Also, clean the wheels after
driving on salted roads.
• Do not wash the wheels with high-speed car wash brushes.
• Do not use any cleaners containing acid or alkaline detergents.
Hyundai_CE_en_US.book Page 49