2023 HYUNDAI I20 Hill start

5-51
05
2. When the front view camera is
adversely affected by an external
condition. Such examples may
include:

[When the vehicle’s headlights have
been damaged or not repaired
properly

[When the vehicle headlights are not
aimed properly

[When the vehicle is driven on a
narrow curved road or rough road

[When the vehicle is driven on an
uphill road or downhill road

[When only part of the vehicle in front
is visible on a crossroad or curved
road

[When there is a traffic light,
reflecting sign, flashing sign or mirror

[When the road conditions are bad
such as being wet or covered with
snow

[When a vehicle suddenly appears
from a curve

[When the vehicle is tilted from a flat
tyre or being towed

[ :KHQ/DQH.HHSLQJ$VVLVWV\VWHP
warning light illuminates

[When the light from the oncoming or
front vehicle is not detected because
of exhaust fume, smoke, fog, snow,
etc.

[When the front window is covered
with foreign matters such as ice,
dust, fog, or is damaged
3. When the forward visibility is poor.
Such examples may include:

[When the headlights of an oncoming
vehicle or a vehicle in front is not
detected due to poor outside
visibility (smog, smoke, dust, fog,
heavy rain, snow, etc.)

[When the windscreen visibility is
poor WARNING

[ 7KHIXQFWLRQPD\QRWZRUNDURXQG
seconds after starting the vehicle or
the initialization or rebooting of the
front view camera.

[ 'RQRWDWWHPSWWRGLVDVVHPEOH
the front view camera without the
assistance of a HYUNDAI authorised
repairer technician.
If the front view camera is removed
for any reason, the system may need
to be re-calibrated. We recommend
that the system be inspected by a
HYUNDAI authorised repairer.

[ ,IWKHZLQGVFUHHQRI\RXUYHKLFOH
is replaced, most likely the front
view camera will need to be
re-calibrated. If this occurs, have
your vehicle inspected and have the
system re-calibrated by a HYUNDAI
authorised repairer.

[ %HFDUHIXOWKDWZDWHUGRHVQ
TWJHWLQWR
front view camera unit and do not
remove or damage related parts of
High Beam Assist system.

[ 'RQRWSODFHREMHFWVRQWKHFUDVK
pad that reflect light such as mirrors,
white paper, etc. The system may
malfunction if sunlight is reflected.

[ $WWLPHV+LJK%HDP$VVLVWPD\
not work properly. The system is
for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.

[ :KHQWKHV\VWHPGRHVQRWRSHUDWH
normally, change the light position
manually between the high beam and
low beam.

Before driving .................................................................................................. 6-4Before entering the vehicle ...................................................................................... 6-4
Before starting ........................................................................................................... 6-4
Ignition switch ................................................................................................. 6-5Key ignition switch .................................................................................................... 6-5
Engine Start/Stop button .......................................................................................... 6-8
Manual transmission .....................................................................................6-13Manual transmission operation ............................................................................... 6-13
Good driving practices ............................................................................................. 6-15
Intelligent Manual Transmission (iMT) .........................................................6-16Intelligent Manual Transmission (iMT) operation .................................................. 6-16
Automatic transmission ............................................................................... 6-20Automatic transmission operation ......................................................................... 6-20
Good driving practices ............................................................................................ 6-24
Dual clutch transmission .............................................................................. 6-26Dual clutch transmission operation ....................................................................... 6-26
Parking ..................................................................................................................... 6-33
Good driving practices ............................................................................................ 6-34
Braking system .............................................................................................. 6-35Power brakes ........................................................................................................... 6-35
Disc brakes wear indicator ..................................................................................... 6-35
Rear drum brakes .................................................................................................... 6-36
Parking brake ........................................................................................................... 6-36
Anti-lock Brake System (ABS) ..................................................................................6-37
Electronic Stability Control (ESC) .......................................................................... 6-39
Vehicle Stability Management (VSM) .....................................................................6-41
Hill-Start Assist Control (HAC) ................................................................................ 6-43
Emergency Stop Signal (ESS) ................................................................................. 6-43
Multi-Collision Brake (MCB) ................................................................................... 6-44
Good braking practices ........................................................................................... 6-45
Idle Stop and Go (ISG) system .....................................................................6-46Activating the ISG .................................................................................................... 6-46
Deactivating the ISG ............................................................................................... 6-46
Condition of ISG system operation ........................................................................ 6-50
ISG Indication ........................................................................................................... 6-51
ISG malfunction ....................................................................................................... 6-52
6. Driving your vehicle
6

6-5
06
IGNITION SWITCH
WARNING
To reduce the risk of SERIOUS
INJURY or DEATH, take the following
precautions:

[NEVER allow children or any person
who is unfamiliar with the vehicle to
touch the ignition switch or related
parts. Unexpected and sudden
vehicle movement can occur.

[NEVER reach through the steering
wheel for the ignition switch, or any
other control, whilst the vehicle is in
motion. The presence of your hand
or arm in this area may cause a loss
of vehicle control resulting in an
accident.
Key ignition switch (if equipped)
OIB054010
WARNING

[NEVER turn the ignition switch to
the LOCK or ACC position whilst
the vehicle is in motion except in
an emergency. This will result in
the engine turning off and loss of
power assist for the steering and
brake systems. This may lead to loss
of directional control and braking
function, which could cause an
accident.

[Before leaving the driver’s seat,
always make sure the shift lever
is in the 1st gear when the vehicle
is parked on an uphill and in
R(Reverse) on a downhill (for manual
transmission vehicle), or P (Park, for
automatic transmission/dual clutch
transmission vehicle) position, apply
the parking brake, and turn the
ignition switch to the LOCK position.
Unexpected vehicle movement may
occur if these precautions are not
followed.
NOTICE
Never use aftermarket keyhole covers.
This may generate start-up failure due
to communication failure.

6-14
Driving your vehicle
Using the clutch (if equipped)
The clutch pedal should be depressed all
the way to the floor before:
- Starting the engine
The engine will not start without
depressing the clutch pedal.
- Shifting
To start your vehicle, slowly release
the clutch pedal and depress the
accelerator.
When releasing the clutch pedal, release
it slowly. The clutch pedal should always
be released whilst driving.
NOTICE
To prevent unnecessary wear or
damage to the clutch:

[Do not rest your foot on the clutch
pedal whilst driving.

[Do not hold the vehicle with the
clutch on an incline, whilst waiting
for the traffic light, etc.

[Always depress the clutch pedal
down fully to prevent noise or
damage.

[Do not start with the 2nd (second)
gear engaged except when you start
on a slippery road.

[Depress the clutch pedal all the way
and be careful not to depress the
pedal again before returning to the
upright position after you release
the pedal. If you depress the pedal
before returning to the original
position repeatedly, it may cause the
clutch system failure.
Downshifting
Downshift when you must slow down in
heavy traffic or drive up a steep hill to
prevent engine load.
Also, downshifting reduces the chance
of stalling and can accelerate when you
need to increase your speed again.
When the vehicle is going downhill,
downshifting helps maintain safe speed
by providing brake power from the
engine and enables less wear on the
brakes.
NOTICE
To prevent damage to the engine,
clutch and transmission:

[When downshifting the 5th gear
to the 4th gear, be careful not to
inadvertently push the shift lever
sideways engaging the 2nd gear.
A drastic downshift may cause the
engine speed to increase to the point
the tachometer will enter the red-
zone.

[Do not downshift more than two
gear at a time or downshift the gear
when the engine is running at high
speed (5,000 RPM or higher). Such
a downshifting may damage the
engine, clutch and the transmission.

6-18
Driving your vehicle

[To avoid premature clutch wear
and damage, do not drive with your
foot resting on the clutch pedal.
Also, don’t use the clutch to hold the
vehicle stopped on an uphill grade,
whilst waiting for a traffic light, etc.

[Do not use the shift lever as a
handrest during driving, as this can
result in premature wear of the
transmission shift forks.

[To prevent possible damage to the
clutch system, do not start with the
2nd (second) gear engaged except
when you start on a slippery road.
WARNING

[Before leaving the driver’s seat,
always set the parking brake fully
and shut the engine off. Then make
sure the transmission is shifted into
the 1st gear when the vehicle is
parked on a level or uphill grade, and
shifted into R (Reverse) on a downhill
grade. Unexpected and sudden
vehicle movement can occur if these
precautions are not followed in the
order identified.

[Do not use the engine brake (shifting
from a high gear to lower gear)
rapidly on slippery roads. The vehicle
may slip causing an accident.
Using the clutch
The clutch should be pressed all the way
to the floor before shifting, then released
slowly. The clutch pedal should always
be fully released whilst driving. Do not
rest your foot on the clutch pedal whilst
driving. This can cause unnecessary
wear. Do not partially engage the clutch
to hold the vehicle on an incline. This
causes unnecessary wear. Use the
foot brake or parking brake to hold the
vehicle on an incline. Do not operate the
clutch pedal rapidly and repeatedly.
CAUTION
When operating the clutch pedal, press
the clutch pedal down fully. If you don’t
press the clutch pedal fully, the clutch
may be damaged or noise may occur.
Downshifting
When you must slow down in heavy
traffic or whilst driving up steep hills,
downshift before the engine starts to
labour. Downshifting reduces the chance
of stalling and gives better acceleration
when you again need to increase your
speed. When the vehicle is traveling
down steep hills, downshifting helps
maintain safe speed and prolongs brake
life.

6-21
06
Transmission ranges
The indicator in the instrument cluster
displays the shift lever position when the
ignition switch is in the ON position.
33DUN
Always come to a complete stop before
shifting into P (Park).
To shift from P (Park), you must depress
firmly on the brake pedal and make sure
your foot is off the accelerator pedal.
If you have done all of the above and
still cannot shift the lever out of P
(Park), see “Shift-Lock Release” in this
chapter.
The shift lever must be in P (Park) before
turning the engine off.
WARNING

[Shifting into P (Park) whilst the
vehicle is in motion may cause you to
lose control of the vehicle.

[After the vehicle has stopped, always
make sure the shift lever is in P (Park),
apply the parking brake, and turn the
engine off.

[When parking on an incline, place the
shift lever in P (Park) and apply the
parking brake to prevent the vehicle
from rolling downhill.

[For safety, always engage the parking
brake with the shift lever in the P
(Park) position except for the case of
emergency parking.
55HYHUVH
Use this position to drive the vehicle
backward.
NOTICE
Always come to a complete stop before
shifting into or out of R (Reverse); you
may damage the transmission if you
shift into R (Reverse) whilst the vehicle
is in motion.
11HXWUDO
The wheels and transmission are not
engaged.
Use N (Neutral) if you need to restart
a stalled engine, or if it is necessary to
stop with the engine ON. Shift into P
(Park) if you need to leave your vehicle
for any reason.
Always depress the brake pedal when
you are shifting from N (Neutral) to
another gear.
WARNING
Do not shift into gear unless your foot is
firmly on the brake pedal. Shifting into
gear when the engine is running at high
speed can cause the vehicle to move
very rapidly. You could lose control of
the vehicle and hit people or objects.
''ULYH
This is the normal driving position. The
transmission will automatically shift
through a 6-gear sequence, providing
the best fuel economy and power.
For extra power when passing another
vehicle or driving uphill, depress the
accelerator fully. The transmission will
automatically downshift to the next
lower gear (or gears, as appropriate).

6-24
Driving your vehicle
Ignition key interlock system
(if equipped)
The ignition key cannot be removed
unless the shift lever is in the P (Park)
position.
3DUNLQJ
Always come to a complete stop and
continue to depress the brake pedal.
Move the shift lever into the P (Park)
position, apply the parking brake, and
place the ignition switch in the LOCK/
OFF position. Take the Key with you
when exiting the vehicle.
WARNING
When you stay in the vehicle with
the engine running, be careful not to
depress the accelerator pedal for a long
period of time. The engine or exhaust
system may overheat and start a fire.
The exhaust gas and the exhaust
system are very hot. Keep away from
the exhaust system components.
Do not stop or park over flammable
materials, such as dry grass, paper or
leaves. They may ignite and cause a
fire.
Good driving practices

[Never move the shift lever from P
(Park) or N (Neutral) to any other
position with the accelerator pedal
depressed.

[Never move the shift lever into P
(Park) when the vehicle is in motion.

[ Be sure the vehicle is completely
stopped before you attempt to shift
into R (Reverse) or D (Drive).

[Do not move the shift lever to N
(Neutral) when driving. Doing so may
result in an accident because of a loss
of engine braking and the transmission
could be damaged.

[Driving uphill or downhill, always shift
to D (Drive) when driving forward or to
R (Reverse) when driving backwards,
and check the gear position indicated
on the cluster before driving. If you
drive in the opposite direction of the
selected gear, the engine will turn
off and a serious accident might be
occurred due to the degraded brake
performance.

[Do not drive with your foot resting
on the brake pedal. Even light, but
consistent pedal pressure can result
in the brakes overheating, brake wear
and possibly even brake failure.

[When driving in manual shift mode,
slow down before shifting to a lower
gear. Otherwise, the lower gear may
not be engaged if the engine rpms are
outside of the allowable range.

[Always apply the parking brake when
leaving the vehicle. Do not depend on
placing the transmission in P (Park) to
keep the vehicle from moving.

[Exercise extreme caution when driving
on a slippery surface. Be especially
careful when braking, accelerating or
shifting gears. On a slippery surface,
an abrupt change in vehicle speed can
cause the drive wheels to lose traction
and may cause loss of vehicle control
resulting in an accident.

6-30
Driving your vehicle
Transmission ranges
The indicator in the instrument cluster
displays the shift lever position when the
ignition switch is in the ON position.
33DUN
Always come to a complete stop before
shifting into P (Park).
To shift from P (Park), you must depress
firmly on the brake pedal and make sure
your foot is off the accelerator pedal.
If you have done all of the above and
still cannot shift the lever out of P
(Park), see “Shift-Lock Release” in this
chapter.
The shift lever must be in P (Park) before
turning the engine off.
WARNING

[Shifting into P (Park) whilst the
vehicle is in motion may cause you to
lose control of the vehicle.

[After the vehicle has stopped, always
make sure the shift lever is in P (Park),
apply the parking brake, and turn the
engine off.

[When parking on an incline, place the
shift lever in P (Park) and apply the
parking brake to prevent the vehicle
from rolling downhill.

[For safety, always engage the parking
brake with the shift lever in the P
(Park) position except for the case of
emergency parking.
55HYHUVH
Use this position to drive the vehicle
backward.
NOTICE
Always come to a complete stop before
shifting into or out of R (Reverse); you
may damage the transmission if you
shift into R (Reverse) whilst the vehicle
is in motion.
11HXWUDO
The wheels and transmission are not
engaged.
Use N (Neutral) if you need to restart
a stalled engine, or if it is necessary to
stop with the engine ON. Shift into P
(Park) if you need to leave your vehicle
for any reason.
Always depress the brake pedal when
you are shifting from N (Neutral) to
another gear.
''ULYH
This is the normal driving position. The
transmission will automatically shift
through a 7-gear sequence, providing
the best fuel economy and power.
For extra power when passing another
vehicle or driving uphill, depress the
accelerator fully. The transmission will
automatically downshift to the next
lower gear (or gears, as appropriate).