2023 HYUNDAI I20 clutch
[x] Cancel search: clutchPage 301 of 649
6-28
Driving your vehicle
NOTICE
V Always come to a complete stop
before shifting into D (Drive) or R
(Reverse).
V Do not put the shift lever in N
(Neutral) whilst driving.
WARNING
Due to transmission failure, you may
not continue to drive and the position
indicator and the position indicator (D,
P) on the instrument cluster will blink.
We recommend that you contact a
HYUNDAI authorised repairer and have
the system checked.
DCT warning messages
This warning message is displayed when
vehicle is driven slowly on a grade and
the vehicle detects that the brake pedal
is not applied.
OBC3070112TU
6 W H H S J U D G H
Driving up hills or on steep grades:
[ To hold the vehicle on an incline use
the foot brake or the parking brake.
[ When in stop-and-go traffic on an
incline, allow a gap to form ahead
of you before moving the vehicle
forward. Then hold the vehicle on the
incline with the foot brake.
[ If the vehicle is held or creeping
forward on an incline by applying
the accelerator pedal, the clutch and
transmission may overheat which
can result in damage. At this time, a
warning message will appear on the
LCD display.
[ If the LCD warning is active, the foot
brake must be applied.
[ Ignoring the warnings can lead to
damage to the transmission.
Page 302 of 649
6-29
06
OBC3070109TU
7 U D Q V P L V V L R Q K L J K W H P S H U D W X U H
[ Under certain conditions, such as
repeated stop-and-go launches on
steep grades, sudden take off or
acceleration, or other harsh driving
conditions, the transmission clutch
temperatures will increase excessively.
Finally the clutch in transmission could
be overheated.
[ When the clutch is overheated, the
safe protection mode engages and the
gear position
[ indicator on the cluster blinks with
a chime. At this time, ‘Transmission
temp is high! Stop safely’ warning
message will appear on the LCD
display and driving may not be
smooth.
[ If this occurs, pull over to a safe
location, stop the vehicle with the
engine running, apply the brakes and
shift the vehicle to P (Park), and allow
the transmission to cool.
[ If you ignore this warning, the driving
condition may become worse. You
may experience abrupt shifts, frequent
shifts, or jerkiness. To return to the
normal driving condition, stop the
vehicle and apply the foot brake or
shift into P (Park). Then allow the
transmission to cool for a few minutes
with engine on, before driving off.
[ When possible, drive the vehicle
smoothly.
OBC3070107TU/OBC3070108TU
7 U D Q V P L V V L R Q R Y H U K H D W H G
[ If the vehicle continues to be driven
and the clutch temperatures reach
the maximum temperature limit,
the ‘Trans Hot! Park with engine on’
warning will be displayed. When this
occurs the clutch is disabled until the
clutch cools to normal temperatures.
[ The warning will display a time to wait
for the transmission to cool.
[ If this occurs, pull over to a safe
location, stop the vehicle with the
engine running, apply the brakes and
shift the vehicle to P (Park), and allow
the transmission to cool.
[ When the message ‘Trans cooled.
Resume driving’, appears you can
continue to drive your vehicle.
[ When possible, drive the vehicle
smoothly.
If any of the warning messages in the
LCD display continue to blink, for your
safety, we recommend that you contact
a HYUNDAI authorised repairer and have
the system checked.
Page 305 of 649
6-32
Driving your vehicle
Paddle shifter (if equipped)
OBC3060004
The paddle shifter is functional when the
shift lever is in the D (Drive) position or
the manual shift mode.
: L W K W K H V K L I W O H Y H U L Q W K H ' S R V L W L R Q
The paddle shifter will operate when
the vehicle speed is more than 6.2mph
(10km/h).
Pull the [+] or [-] paddle shifter once
to shift up or down one gear and the
system changes from automatic mode
to manual mode.
When the vehicle speed is lower than
6.2mph (10km/h), if you depress the
accelerator pedal for more than 6
seconds or if you move the shift lever
from D (Drive) to manual shift mode and
move it from manual shift mode to D
(Drive) again, the system changes from
manual mode to automatic mode.
: L W K W K H V K L I W O H Y H U L Q W K H P D Q X D O
V K L I W P R G H
Pull the [+] or [-] paddle shifter once to
shift up or down one gear.
i Information
, I W K H > @ D Q G > @ S D G G O H V K L I W H U V D U H S X O O H G
D W W K H V D P H W L P H J H D U V K L I W P D \ Q R W
R F F X U
Shift-lock system
For your safety, the dual clutch
transmission has a shift-lock system
which prevents shifting the transmission
from P (Park) into R (Reverse) unless the
brake pedal is depressed.
To shift the transmission from P (Park)
into R (Reverse):
1. Depress and hold the brake pedal.
2. Start the engine or place the ignition
switch in the ON position.
3. Move the shift lever.
Page 309 of 649
6-36
Driving your vehicle
Rear drum brakes
Your rear drum brakes do not have wear
indicators. Therefore, have the rear
brake linings inspected if you hear a rear
brake rubbing noise. Also have your rear
brakes inspected each time you change
or rotate your tyres and when you have
the front brakes replaced.
Parking brake
OBC3060005
Always set the parking brake before
leaving the vehicle, to apply:
Firmly depress the brake pedal.
Pull up the parking brake lever as far as
possible.
WARNING
To reduce the risk of SERIOUS INJURY
or DEATH, do not operate the parking
brake whilst the vehicle is moving
except in an emergency situation. It
could damage the brake system and
lead to an accident.
OBC3060006
To release:
Firmly depress the brake pedal.
Slightly pull up the parking brake lever.
Whilst pressing the release button (1),
lower the parking brake (2).
If the parking brake does not release
or does not release all the way, we
recommend that the system be checked
by a HYUNDAI authorised repairer.
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal.
Move the shift is in the 1st gear when
the vehicle is parked on a uphill and in
R (Reverse) on an downhill (for manual
transmission vehicle), or P (Park, for
automatic transmission/dual clutch
transmission vehicle) position, then
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
Page 318 of 649
6-45
06
Good braking practices
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal. Move the shift lever into the 1st
gear (for Manual transmission vehicle)
or N (Neutral) position (for Automatic
transmission/Dual clutch transmission
vehicle), then apply the parking brake,
and place the ignition switch in the
LOCK/OFF position.
Vehicles parked with the parking brake
not applied or not fully engaged may
roll inadvertently and may cause injury
to the driver and others. ALWAYS apply
the parking brake before exiting the
vehicle.Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it is
washed.
Your vehicle will not stop as quickly if
the brakes are wet. Wet brakes may
cause the vehicle to pull to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns to
normal. If the braking action does not
return to normal, stop as soon as it is
safe to do so and we recommend that
you call a HYUNDAI authorised repairer
for assistance.
DO NOT drive with your foot resting on
the brake pedal. Even light, but constant
pedal pressure can result in the brakes
overheating, brake wear, and possibly
even brake failure.
If a tyre goes flat whilst you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead whilst you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.
Page 320 of 649
6-47
06
Auto stop
OBC3060009
7 R V W R S W K H H Q J L Q H L Q L G O H V W R S P R G H
H [ F H S W 9 0 + ( 9
Manual Transmission/Intelligent
Manual Transmission
1. Decrease the vehicle speed to less
than 3 mph (5 km/h).
2. Shift into N (Neutral) position.
3. Release the clutch pedal.
Automatic Transmission/Dual Clutch
Transmission
1. Decrease the vehicle speed to 0 mph
(0 km/h).
2. Press the brake pedal.
The engine will stop and the green AUTO
STOP indicator (
) on the instrument
cluster will illuminate.
NOTICE
[ 9 H K L F O H Z K L F K L V H T X L S S H G Z L W K
manual transmission or intelligent
manual transmission must reach
a speed of at least 5 mph (8 km/h)
since last idle stop and vehicle
which is equipped with automatic
transmission or dual clutch
transmission must reach a speed of
at least 3 mph (5 km/h) since last idle
stop.
[ , I \ R X X Q I D V W H Q W K H V H D W E H O W R U R S H Q
the driver’s door (engine bonnet), ISG
system will be deactivated.
7 R V W R S W K H H Q J L Q H L Q L G O H V W R S P R G H
I R U 9 0 + ( 9
Manual Transmission/Intelligent
Manual Transmission
Three versions of idle stop are available
for MHEV which is equipped with
manual transmission or intelligent
manual transmission.
- Conventional Idle STOP
[ ' H F U H D V H W K H Y H K L F O H V S H H G W R O H V V
than 4 mph (7 km/h).
[ 6 K L I W L Q W R 1 1 H X W U D O S R V L W L R Q
[ 5 H O H D V H W K H F O X W F K S H G D O
- Extended Idle STOP
[ ' H S U H V V W K H E U D N H S H G D O
[ ' H S U H V V W K H F O X W F K S H G D O
- During Sailing Mode
You can keep engine off status from
sailing to standstill by pressing clutch
and brake pedal nearly at the same time.
NOTICE
1. If last gear position was the 1st, ISG
STOP will not be activated.
2. Vehicle which is equipped with
manual transmission or intelligent
manual transmission must reach
a speed of at least 5 mph (8 km/h)
since last idle stop.
3. During ISG STOP status, you can shift
into N(Neutral) position and release
clutch pedal, then ISG STOP status
will remain as STOP.
4. Extended Idle STOP operates even
over 4 mph (7km/h) if it meets the
speed requirement in each gear
position. (example: Extended Idle
STOP operates even at the 3rd speed,
24 mph (40km/h)).
5. If you unfasten the seat belt or open
the driver’s door (engine bonnet), ISG
system will be deactivated.
Page 321 of 649
6-48
Driving your vehicle
Automatic Transmission/Dual Clutch
Transmission
- Conventional Idle STOP
[ ' H F U H D V H W K H Y H K L F O H V S H H G W R P S K
(0 km/h).
[ 3 U H V V W K H E U D N H S H G D O
- Extended Idle STOP
[ ' H F U H D V H W K H Y H K L F O H V S H H G O H V V W K D Q
15 mph (25 km/h).
[ 3 U H V V W K H E U D N H S H G D O
- During Sailing Mode
You can keep engine off status from
sailing to standstill by pressing brake
pedal below 24 mph (40 km/h).
NOTICE
Vehicle which is equipped automatic
transmission or dual clutch
transmission must reach a speed of at
least 18 mph (30 km/h) for Extended
Idle STOP or 3 mph (5 km/h) for
Conventional Idle STOP since last idle
stop.
- If you unfasten the seat belt or open
the driver’s door (engine bonnet)
in auto stop mode at standstill, ISG
system will be deactivated.
Auto start
To restart the engine from idle stop
mode (except 48V MHEV)
Manual transmission vehicle/ Intelligent
Manual Transmission
Vehicle which is equipped with manual
transmission or intelligent manual
transmission is available two version of
restart.
- Conventional restart
Press the clutch pedal when the shift
lever is in the N (Neutral) position.
- Late restart (if equipped)
1. Depress the clutch pedal
2. Engage the gear
3. Release the brake pedal
NOTICE
1. Late restart function is only operated
when it is on a level ground and the
vehicle is stable.
2. To start the engine when the brake
pedal is not pressed or gear is already
engaged, press the brake pedal first
and press on the clutch pedal for
safety.
3. To turn on the engine without vehicle
movement with the brake pedal
pressed (only with Late Restart),
[ 3 U H V V D Q G U H O H D V H W K H F O X W F K S H G D O
[ 3 U H V V W K H F O X W F K S H G D O D J D L Q
immediately
4. After the engine stall, If you operate
as below the engine will start.
[ 5 H O H D V H W K H F O X W F K S H G D O D I W H U W K H
engine completely stop
[ ' H S U H V V W K H F O X W F K S H G D O
Page 322 of 649
6-49
06
Automatic Transmission/Dual Clutch
Transmission
- Release the brake pedal.
The engine will start and the green AUTO
STOP indicator (
) on the instrument
cluster will go out.
7 R U H V W D U W W K H H Q J L Q H I U R P L G O H V W R S
P R G H I R U 9 0 + ( 9
Manual Transmission/Intelligent
Manual Transmission
- Before standstill
Press the clutch pedal if the clutch pedal
has not pressed.
If the clutch pedal has already been
pressed, release the brake pedal or
move the gear to a position other than N
position.
- After standstill
[ , I W K H F O X W F K S H G D O K D V D O U H D G \ E H H Q
pressed, release the brake pedal or
move the gear from N (Neutral).
[ , I W K H F O X W F K S H G D O L V Q R W S U H V V H G W K H
engine will restart in accordance with
the LATE Restart procedure.
1) Depress the clutch pedal
2) Engage the gear
3) Release only the brake pedal
NOTICE
1. Late restart function is only operated
when it is on a level ground and the
vehicle is stable.
2. To start the engine when the brake
pedal is not pressed or gear is already
engaged, press the brake pedal first
and press on the clutch pedal for
safety.
3. To turn on the engine without vehicle
movement with the brake pedal
pressed (only with Late Restart),
[ 3 U H V V D Q G U H O H D V H W K H F O X W F K S H G D O
[ 3 U H V V W K H F O X W F K S H G D O D J D L Q
immediately
4. After the engine stall, if you operate
as below the engine will start.
[ 5 H O H D V H W K H F O X W F K S H G D O D I W H U W K H
engine completely stops
[ ' H S U H V V W K H F O X W F K S H G D O
5. After operating ISG STOP, if the
vehicle speed increases instead of
decreasing, the engine may restart
automatically.
Automatic Transmission/Dual Clutch
Transmission
Release the brake pedal
NOTICE
After operating ISG STOP, if the vehicle
speed increases instead of decreasing,
the engine may restart automatically.