Page 788 of 840
786
Handling the Unexpected
If the Battery Is Dead
Jump Starting Procedure
Turn off the power to electric devices, such as audio and lights. Turn off the engine,
then open the hood.1 If the Battery Is Dead
Securely attach the jumper cables clips so that they
do not come off when the e ngine vibrates. Be careful
not to tangle the jumper cables or allow the cable
ends to touch each other while attaching or
detaching the jumper cables.
3WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 786 ページ 2022年6月23日 木曜日 午後9時28分
Page 789 of 840
787
uuIf the Battery Is Dead uJump Starting Procedure
Continued
Handling the Unexpected
1. Open the cover on the positive + terminal.
2. Connect the first jumper cable to your
vehicle's battery + terminal.
3. Connect the other end of the first jumper
cable to the booster battery + terminal.
u Use a 12-volt booster battery only.
u When using an automotive battery
charger to boost your 12-volt battery,
select a lower charging voltage than
15-volt. Check the charger manual for
the proper setting.
4. Connect the second jumper cable to the
booster battery - terminal.
Booster Battery
1.5 L engine models
Booster Battery
2.0 L engine models
with Auto Idle Stop
2.0 L engine models
without Auto Idle Stop
Booster Battery
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 787 ページ 2022年6月23日 木曜日 午後9時28分
Page 790 of 840
uuIf the Battery Is Dead uJump Starting Procedure
788
Handling the Unexpected
5. Connect the other end of the second
jumper cable to the stud bolt as shown. Do
not connect this jumper cable to any other
part.
6. If your vehicle is connected to another
vehicle, start the assi sting vehicle's engine
and increase its rpm slightly.
7. Attempt to start your vehicle's engine. If it
turns over slowly, check that the jumper
cables have good metal-to-metal contact.1If the Battery Is Dead
Battery performance degrades in cold conditions and
may prevent the engi ne from starting.1.5 L engine models
2.0 L engine models
with Auto Idle Stop
2.0 L engine models
without Auto Idle Stop
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 788 ページ 2022年6月23日 木曜日 午後9時28分
Page 791 of 840

789
uuIf the Battery Is Dead uJump Starting Procedure
Handling the Unexpected
Once your vehicle's engine has started, re move the jumper cables in the following
order.
1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jump er cable from the booster battery -
terminal.
3. Disconnect the jumper cable from your vehicle's battery + terminal.
4. Disconnect the other end of the jump er cable from the booster battery +
terminal.
Have your vehicle inspected by a n earby service station or a dealer.
■What to Do After the Engine Starts1What to Do After the Engine Starts
The Vehicle Stability Assist
TM (VSA ®) system, Vehicle
Stability AssistTM (VSA ®) OFF*, Adaptive Cruise Control
(ACC) with Low Speed Follow*, safety support and low
tire pressure/ TPMS* indicators may come on in amber
along with a message in the gauge when you set the
power mode to ON after reconnecting the battery.
Drive a short distance at more than 12 mph (20 km/h).
Each indicator should go off. If any do not, have your
vehicle checked by a dealer.
* Not available on all models
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 789 ページ 2022年6月23日 木曜日 午後9時28分
Page 798 of 840

796
uuIndicator, Coming On/BlinkinguIf the Charging System Indicator Comes On
Handling the Unexpected
If the Charging System Indicator Comes On
■Reasons for the indicator to come on
Comes on when there is a prob lem with the charging system.
■What to do when the indicator comes on
Stop in a safe place and have yo ur vehicle checked by a dealer
immediately.
If the Malfunction Indicator Lamp Comes On or Blinks
■Reasons for the indicator la mp to come on or blink
• Comes on when there is a problem with the engine emissions control
system.
• Blinks when engine misfiring is detected.
■What to do when the indicator lamp comes on
Avoid high speeds and immediately get your vehicle inspected at a
dealer.
■What to do when the indicator lamp blinks
Park the vehicle in a safe place with no flammable items and wait at least
10 minutes or more with the engine stopped until it cools.
1 If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engi ne may rapidly discharge
the battery.
1 If the Malfunction Indicato r Lamp Comes On or Blinks
NOTICE
If you drive with the malf unction indicator lamp on,
the emissions control system and the engine could be
damaged.
If the malfunction indicator lamp blinks again when
restarting the engine, drive to the nearest dealer at
31 mph (50 km/h) or less. Have your vehicle
inspected.
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 796 ページ 2022年6月23日 木曜日 午後9時28分
Page 803 of 840
801Continued
Handling the Unexpected
Fuses
Fuse Locations
If any electrical devices are not working, set the power mode to VEHICLE OFF and
check to see if any applicable fuse is blown.
Located near the battery. Push the tabs to open the box.
Fuse locations are shown on the fuse box cove r. Locate the fuse in question by the
fuse number and box cover number.
■Engine Compartment Fuse Box
Fuse Box
Tab
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 801 ページ 2022年6月23日 木曜日 午後9時28分
Page 804 of 840

802
uuFuses uFuse Locations
Handling the Unexpected
■Circuit protected and fuse rating
Circuit ProtectedAmps
1BATTERY125 A
2 —4
0 A
—4 0 A
F/BOX OPTION 60 A —4 0 A
F/BOX OPTION2 40 A DC/DC2
*(30 A)
F/BOX MAIN 60 A
3
—40 A
—40 A
—40 A
RR DEFROSTER40 A
—40 A
HTR MTR40 A
—40 A
4 —3
0 A
ABS/VSA MTR 40 A DC/DC
*(30 A)
—30 A
IG MAIN 30 A —30 A
R/M2 30 A
5
ST MAGNETIC SW30 A
WIPER30 A
EPS70 A
R/M1*
RFC
30 A*1
50 A*2
ABS/VSA FSR40 A
MAIN FAN*1
R/M1*230 A
F/BOX MAIN240 A
6 SUB FAN
— 30 A*1
—*2
7 IG MAIN230 A
8 —
ACTIVE EXHAUST VALVE —*1
7.5 A*2
9EVP*(30 A)
10 AUDIO SUB*(7.5 A)
11——
12 — —
13H/STRG*(10 A)
14 — —
15FR FOG*(10 A)
16 MG CLUTCH 10 A*1
(10 A)*2
17WASHER15 A
18 HORN 10 A
19BACK UP15 A
20 AUDIO (15 A)
Circuit ProtectedAmps
*1:Models with Auto Idle Stop
*2:Models without Auto Idle Stop
21—
RFC RLY CL+—*1
7.5 A*2
22 DBW 15 A
23EOP*(20 A)
24 BACKUP FI-ECU 10 A
25IGP15 A
26 TCU*(15 A)
27LCM L(15 A)
28 INJ*
— (15 A)
*1
—*2
29STOP10 A
30 LCM R (15 A)
31IG COIL15 A
32 — —
33HAZARD15 A
34 AUDIO SUB VST*(7.5 A)
35——
36 AUDIO VST MAIN*(30 A)
37BACKUP2 —(30 A)*1
—*2
38 — —
39——
40 VBACT*(10 A)
41IGPS [LAF]10 A
Circuit ProtectedAmps
* Not available on all models
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 802 ページ 2022年6月23日 木曜日 午後9時28分
Page 822 of 840

820
Information
Emissions Testing
Testing of Readiness Codes
Your vehicle has readiness code as part of the onboard self diagnostic system.
Some states use these codes for testing to verify whether your vehicle's emissions
components are working properly.
The codes may not be read properly if testin g is performed just after the battery has
gone dead or been disconnected.
To check if they are set, set the power mo de to ON, without starting the engine. The
malfunction indicator lamp will come on for several seconds. If it then goes off, the
readiness codes are set. If it blinks fi ve times, the readiness codes are not set.
If you are required to have your vehicle te sted before the readiness codes are ready,
prepare the vehicle for retesting by doing the following:
1. Fill the gas tank to approximately 3/4 full.
2. Park the vehicle and leave the engine off for 6 hours or more.
3. Make sure the ambient temperature is between 40°F and 95°F (4°C and 35°C).
4. Start the engine without touching the ac celerator pedal, and let it idle for
20 seconds.
5. Keep the vehicle in
(P (continuously variable transmission) or (N (manual
transmission). Increase the engine speed to 2,000 rpm, and hold it there for
about 3 minutes.
6. Let the engine idle with your foot off the accelerator for 20 seconds.
1Testing of Readiness Codes
The readiness codes are erased when the battery is
disconnected, and set again only after several days of
driving under a variety of conditions.
If a testing facility determines that the readiness
codes are not set, you may be requested to return at
a later date to complete the test.
If the testing facility determines the readiness codes
are still not set, see a dealer.
1.5 L engine models
23 CIVIC HATCHBACK TYPE R-31T406100_03.book 820 ページ 2022年6月23日 木曜日 午後9時28分