2023 GENESIS GV60 maintenance

9-44
Maintenance
Instrument panel fuse panel
Fuse NameFuse Rating Circuit Protected
WIPER FRT 215A Multifunction Switch
SPEAR (IG2)10A Not Used
MODULE 37.5AStop Lamp Switch, IAU, IBU, CCU, Multifunction Switch,
Driver/Passenger Door DSM Monitor, Driver Power
Window Switch, Overhead Console
MULTIMEDIA25A CCIC Head Unit
AIRBAG 210A SRS Control Module
START7.5A VCU, IBU
A/C 210A A/C Control Module

9-46
Maintenance
Vehicle compartment fuse panel
Type Fuse NameFuse Rating Circuit Protected
MULTI
FUSE-1LDC200A P/R Junction Block (Fuse : F2, S1, S2, S3, S4, S5)
MDPS1 *1100A MDPS Unit
MULTI
FUSE-2C/FAN80A Cooling Fan Motor
RR HTD150A P/R Junction Block (RLY.3)
B+150A ICU Junction Block (IPS1, IPS2, IPS3, IPS4, IPS5)
TRAILER150A CTM (CAN Type Trailer Module)
B+240A ICU Junction Block (IPS6, IPS7, IPS8)
MULTI
FUSE-3B+560A PCB Block (IG3 Main Relay, Fuse : F2, F3, F4, F6)
B+360AICU Junction Block (Fuse : F1, F11, F12, F21, F22,
F31,F32, F41, F42, F51)
BLOWER50A P/R Junction Block (RLY.9)
IEB160A IEB Unit
IEB260A IEB Unit
IG140A P/R Junction Block (RLY.5, RLY.7)
IG240A P/R Junction Block (RLY.10)
*1 : MDPS (Motor Driven Power Steering) is the same as EPS (Electric Power Steering)

9-48
Maintenance
Motor compartment fuse panel
Type Fuse NameFuse Rating Circuit Protected
FUSEEWP 120A Electronic Water Pump #1 (HV Battery)
EWP 220A Electronic Water Pump #2 (HV Battery)
PRESAFETY
SEAT BELT 230A Preactive Seat Belt
TRAILER 220A CTM (CAN Type Trailer Module)
PRESAFETY
SEAT BELT 30A Preactive Seat Belt
MIRR HTR10A Driver/Passenger Outside Mirror Unit
E-SHIFTER 210ASCU, Electronic ATM Shift Lever, P/R Junction
Block (RLY.2)
POWER
OUTLET 320A Luggage Power Outlet
POWER
OUTLET 220A Front Power Outlet

9-50
Maintenance
Information

[A normally functioning lamp may
flicker momentarily to stabilize the
vehicle’s electrical control system.
However, if the lamp goes out after
flickering momentarily, or continues
to flicker, have the system be checked
by an authorized retailer of Genesis
Branded products.

[The parking lamp may not turn on
when the parking lamp switch is turned
on, but the parking lamp and headlamp
switch may turn on when the headlamp
switch is turned on. This may be caused
by network failure or vehicle electrical
control system malfunction. If this
occurs, have the system be checked
by an authorized retailer of Genesis
Branded products.
Information
The headlamp aiming should be adjusted
after an accident or after the headlamp
assembly is reinstalled.
Headlamp, Parking Lamp, Turn
Signal Lamp, Daytime Running
Light (DRL) Replacement
OJWEV091051N
(1) Headlamp (Low)
(2) Headlamp (High / Sub low)
(3) Parking lamp/Daytime running light/
Turn signal lamp
(4) Front side marker
If the LED lamp does not operate,
have the system be inspected by an
authorized retailer of Genesis Branded
products.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.

9-52
Maintenance
High Mounted Stop Lamp
Replacement
OJWEV091052N
If the LED lamp (1) does not operate,
have the system be inspected by an
authorized retailer of Genesis Branded
products.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.
License Plate Lamp Replacement
OJWEV091018
If the LED lamp (1) does not operate,
have the system be inspected by an
authorized retailer of Genesis Branded
products.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.

9-54
Maintenance
„Vanity mirror lamp
ORG3EV091033
„Glove box lamp
OJWEV091020
„Mood lamp
OJWEV051243L
„Luggage compartment lamp
OJWEV051062N
If the LED lamp does not operate,
have the system be inspected by an
authorized retailer of Genesis Branded
products.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.

9-55
09
Exterior Care
NOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp
or outside rearview mirror might be
damaged due to sunlight reflected from
the sign or building. To prevent damage
of the exterior plastic parts, you should
avoid parking in areas where light may
be reflected or use a car cover. (The
exterior plastic parts applied to your
vehicle may vary.)
Do not step on the side sill moldings.
Excessive load may result in vehicle
damage or personal injury.
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Washing
To help protect your vehicle’s finish from
rust and deterioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
High-pressure washing

[When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

[Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.

[Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.
APPEARANCE CARE

9-56
Maintenance
NOTICE

[Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.

[Be careful when washing the side
windows of your vehicle.

[Especially, with high-pressure water,
water may leak through the windows
and wet the interior.

[To prevent damage to the plastic
parts, do not clean with chemical
solvents or strong detergents.
NOTICE
OJWEV091026N

[Water washing in the motor
compartment including high
pressure water washing may cause
the failure of electrical circuits
located in the vehicle compartment.

[Never allow water or other liquids
to come in contact with electrical/
electronic components inside the
vehicle as water or other liquids may
flow in to the motor compartment
through the front trunk and damage
electrical/electronic components.
NOTICE
Matte paint finish vehicle (if equipped)
Automatic car wash which uses rotating
brushes should not be used as this can
damage the surface of your vehicle. A
steam cleaner which washes the vehicle
surface at high temperature may result
the oil to adhere and leave stains that is
difficult to remove.
Use a soft cloth (for example, microfiber
towel or sponge) when washing your
vehicle and dry with a microfiber towel.
When you hand wash your vehicle, you
should not use a cleaner that finishes
with wax. If the vehicle surface is too
dirty (sand, dirt, dust, contaminant,
etc.), clean the surface with water
before washing the car.
Waxing
A good coat of wax is a barrier between
your paint and contaminate. Keeping
a good coat of wax on your vehicle will
help protect it.
Wax the vehicle when water will no
longer bead on the paint.
Always wash and dry the vehicle before
waxing. Use a good quality liquid or
paste wax, and follow the manufacturer’s
instructions. Wax all metal trim to protect
it and to maintain its luster.
Removing oil, tar, and similar materials
with a spot remover will usually strip the
wax from the finish. Be sure to re-wax
these areas even if the rest of the vehicle
does not yet need waxing.