2023 GENESIS G90 tire pressure

8-21
08
Notes On the Safe Use of the Tire
Mobility Kit
• Park your vehicle at the side of the
road so that you can work with the
Tire Mobility Kit away from moving
traffic.
• To be sure your vehicle will not move,
even when you’re on fairly level
ground, always set your parking brake.
• Only use the Tire Mobility Kit for
sealing/inflation passenger vehicle
tires. Only punctured areas located
within the tread region of the tire can
be sealed using the tire mobility kit.
• Do not use on motorcycles, bicycles
or any other type of tires.
• When the tire and wheel are
damaged, do not use Tire Mobility Kit
for your safety.
• Use of the Tire Mobility Kit may not be
effective for tire damage larger than
approximately 0.16 in. (4 mm).
Please contact the nearest retailer of
Genesis Branded products if the tire
cannot be made roadworthy with the
Tire Mobility Kit.• Do not use the Tire Mobility Kit if a tire
is severely damaged by driving run flat
or with insufficient air pressure.
• Do not remove any foreign objects
such as nails or screws that have
penetrated the tire.
• Provided the vehicle is outdoors,
leave the engine running. Otherwise
operating the compressor may
eventually drain the vehicle battery.
• Never leave the Tire Mobility Kit
unattended while it is being used.
• Do not leave the compressor running
for more than 10 minutes at a time or
it may overheat.
• Do not use the Tire Mobility Kit if the
ambient temperature is below -22°F
(-30°C).
• In case of skin contact with the
sealant, wash the area thoroughly
with plenty of water. If the irritation
persists, seek medical attention.
• In case of eye contact with the
sealant, flush your eyes for at least 15
minutes. If the irritation persists, seek
medical attention.
• In case of swallowing the sealant,
rinse the mouth and drink plenty of
water. However, never give anything
to an unconscious person and seek
medical attention immediately.
• Long time exposure to the sealant
may cause damage to bodily tissue
such as kidney, etc.
008_RS4_HMA.indd 8-212022-04-18  3:48:11

8-22
Emergency Situations
Components of the Tire Mobility Kit
ONE1081030ONE1081030
M Speed restriction label
N Sealant bottle and label with speed restriction
O Filling hose
P Connectors and cable for power outlet direct connection
Q Holder for the sealant bottle
R Compressor
S ON/OFF switch
T Pressure gauge for displaying the tire inflation pressure
U Button for reducing the tire inflation pressure
Connectors, cable and connection hose are stored in the compressor housing.
Strictly follow the specified sequence, otherwise the sealant may escape under high
pressure.
008_RS4_HMA.indd 8-222022-04-18  3:48:11

8-23
08
WARNING
Expired sealant
Do not use the Tire sealant after the
sealant has expired (for example, past
the expiration date on the sealant
container). This can increase the risk of
tire failure.
WARNING
Sealant
• Keep out of reach of children.
• Avoid contact with eyes.
• Do not swallow.
Using the Tire Mobility Kit
WARNING
ORS081007ORS081007
Detach the speed restriction label M
from the sealant bottle N, and place
it in a highly visible place inside the
vehicle such as on the steering wheel to
remind the driver not to drive too fast.
CAUTION
If only the tire pressure needs to be
adjusted, refer to “How to Adjust Tire
Pressure” in this chapter. Before using
the Tire Mobility Kit, be fully aware of
the explanation on the sealant.
ORG3EV081022ORG3EV081022
1. Shake the sealant bottle N.
ORS081022ORS081022
2. Connect the filling hose O to the
sealant bottle N in the direction of
A and connect the sealant bottle to
the sealant bottle holder Q in the
direction of
B.
3. Ensure that the compressor is
switched OFF.
008_RS4_HMA.indd 8-232022-04-18  3:48:12

8-24
Emergency Situations
ORS081008LORS081008L
4. Unscrew the valve cap from the valve
of the defective wheel and screw the
filling hose O of the sealant bottle
onto the valve.
CAUTION
Securely install the sealant filling hose
to the valve. If not, sealant may flow
backward, possibly clogging the filling
hose.
ORS081009ORS081009
5. Plug the compressor power cord P
into the vehicle power outlet.
NOTICE
Only use the front passenger side
power outlet when connecting the
power cord.6. With the Engine Start/Stop button
in the ON position, switch on
the compressor and let it run for
approximately 5~7 minutes to fill the
sealant up to proper pressure. (refer
to the Tire and Wheels, chapter 2).
The inflation pressure of the tire after
filling is unimportant and will be
checked/ corrected later. Be careful
not to overinflate the tire and stay
away from the tire when filling it.
CAUTION
Tire pressure
Do not attempt to drive your vehicle if
the tire pressure is below 200 kPa (29
psi). This could result in an accident due
to sudden tire failure.
WARNING
Carbon monoxide
Do not leave your vehicle running in
a poorly ventilated area for extended
periods of time. Carbon monoxide
poisoning and suffocation can occur.
7. Switch off the compressor.
8. Detach the hoses from the sealant
bottle connector and from the tire
valve.
008_RS4_HMA.indd 8-242022-04-18  3:48:14

8-25
08
Return the Tire Mobility Kit to its storage
location in the vehicle.
ORS081024LORS081024L
9. Immediately drive approximately 4~6
miles (7~10 km or, about 10min) to
evenly distribute the sealant in the
tire.
Do not exceed a speed of 50 mph (80
km/h). If possible, do not fall below a
speed of 12 mph (20 km/h).
While driving, if you experience any
unusual vibration, ride disturbance or
noise, reduce your speed and drive with
caution until you can safely pull off of the
side of the road.Call for road side service or towing.ORS081008LORS081008L
10. After driving approximately 4~6 miles
(7~10 km or about 10 min), stop at a
safety location.
11. Connect the filling hose O of the
compressor directly to the tire valve.
12. Connect between compressor and the
vehicle power outlet using the cable
and connectors.
13. Adjust the tire inflation pressure to
the recommended tire inflation. With
the ignition switched on, proceed as
follows.
-To increase the inflation pressure:
Switch on the compressor. To
check the current inflation pressure
setting, briefly switch off the
compressor.
-To reduce the inflation pressure:
Press the button U on the
compressor.
008_RS4_HMA.indd 8-252022-04-18  3:48:14

8-26
Emergency Situations
NOTICE
Do not let the compressor run for more
than 10 minutes, otherwise the device
will overheat and may be damaged.
Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tire pressure,
the compressor needs to be turned off.
CAUTION
If the inflation pressure is not
maintained, drive the vehicle a second
time, refer to step 9.
Then repeat steps 10 to 13.
Use of the TMK may be ineffectual for
tire damage larger than approximately
0.16 in (4 mm).
We recommend that you contact an
authorized retailer of Genesis Branded
products if the tire cannot be made
roadworthy with the Tire Mobility Kit.
WARNING
The tire inflation pressure must be at
least 32 psi (220 kPa). If it is not, do not
continue driving.
Call for road side service or towing.
CAUTION
Tire pressure sensor (if equipped with
TPMS)
The sealant on the tire pressure sensor
and wheel should be removed when
you replace the tire with a new one
and inspect the tire pressure sensors.
Have you get this done at an authorized
retailer of Genesis Branded products.
Information
When reinstalling the repaired or replaced
tire and wheel on the vehicle, tighten the
wheel bolt to 101~116 lbf·ft (14~16 kgf·m).
008_RS4_HMA.indd 8-262022-04-18  3:48:14

8-27
08
How to Adjust Tire Pressure
ORS081008LORS081008L
1. Park your vehicle in a safe location.
2. Connect the filling hose O of the
compressor directly to the tire valve.
3. Plug the compressor power cord into
the vehicle power outlet.
4. Adjust the tire inflation pressure to
the recommended tire inflation. With
the ignition switched on, proceed as
follows.
-To increase the inflation pressure:
Switch on the compressor. To
check the current inflation pressure
setting, briefly switch off the
compressor.
-To reduce the inflation pressure:
Press the button U on the
compressor.
NOTICE
Do not let the compressor run for more
than 10 minutes, otherwise the device
will overheat and may be damaged.
Information
• The pressure gauge may show
higher than actual reading when the
compressor is running. To get an
accurate tire reading, the compressor
needs to be turned off.
• When reinstalling the repaired or
replaced tire and wheel on the vehicle,
tighten the wheel bolt to 101~116 lbf·ft
(14~16 kgf·m).
CAUTION
Do not use the sealant when the tire
pressure only needs to be adjusted.
WARNING
The tire inflation pressure must be at
least 32 psi (220 kPa). If it is not, do not
continue driving.
Call for road side service or towing.
008_RS4_HMA.indd 8-272022-04-18  3:48:15

9
Tires and Wheels ............................................................................................. 9-33Tire Care ......................................................................................................................9-33
Recommended Cold Tire Inflation Pressures ...........................................................9-33
Check tire Inflation Pressure .....................................................................................9-34
Tire Rotation ...............................................................................................................9-35
Wheel Alignment and Tire Balance ...........................................................................9-36
Tire Replacement .......................................................................................................9-36
Wheel Replacement ................................................................................................... 9-37
Tire Traction ................................................................................................................ 9-37
Tire Maintenance........................................................................................................ 9-37
Tire Sidewall Labeling ............................................................................................... 9-38
Tire Terminology and Definitions .............................................................................. 9-41
All Season Tires .......................................................................................................... 9-44
Snow Tires.................................................................................................................. 9-44
Radial-Ply Tires .......................................................................................................... 9-44
Low Aspect Ratio Tires .............................................................................................. 9-45
Fuses ................................................................................................................9-46Instrument Panel Fuse Replacement ........................................................................9-47
Engine Compartment Panel Fuse Replacement ..................................................... 9-48
Fuse/Relay Panel Description................................................................................... 9-49
Light Bulbs ....................................................................................................... 9-62Headlight, Parking Lamp, Turn Signal Lamp, Daytime Running Light (DRL)
Replacement ............................................................................................................. 9-63
Side Repeater Lamp Replacement .......................................................................... 9-63
Puddle Lamp Replacement ...................................................................................... 9-63
Rear Combination Lamp Replacement ................................................................... 9-64
High Mounted Stop Lamp Replacement ................................................................. 9-64
License Plate Lamp Replacement ............................................................................ 9-65
Interior light replacement ......................................................................................... 9-65
Appearance Care ............................................................................................ 9-67Exterior Care ...............................................................................................................9-67
Interior Care ................................................................................................................ 9-7 2
Emission Control System ................................................................................ 9-76Crankcase Emission Control System ........................................................................ 9-76
Evaporative Emission Control System Including Onboard Refueling Vapor
Recovery (ORVR) ........................................................................................................ 9-76
Exhaust Emission Control System ............................................................................. 9-77
California Perchlorate Notice ......................................................................... 9-78