2023 GENESIS G90 change time

3-36
Safety System
Front air ventilation seats (if
equipped)
ORS031041
While the engine is on, press the seat
ventilator button on the center console
to select the intensity level.

[Ventilation intensity level can be
adjusted to strong, medium, or weak.
Pressing the button each time will
change the intensity in turn from
strong, to medium, weak, and off.

[Press and hold the seat ventilator
button to turn it off.

[Auto. Controls That Use Climate
Control Settings (for driver’s seat)
The air ventilation seat automatically
controls the seat temperature
depending on the ambient
temperature when the engine is
running.
To use this function, it must be
enabled from the Settings menu in the
infotainment system screen. Select:
-6HWXS

4-21
04
LCD Display Messages
Vehicle is on
This message is displayed if you open the
driver’s door when the gear is in P (Park)
and the Engine Start/Stop button in the
ON or START position.
Turn the engine off before leaving the
vehicle.
Shift to P
This message is displayed if you try to
turn off the vehicle without the gear in
the P (Park) position.
If this occurs, the Engine Start/Stop
button turns to the ACC position.
Vehicle is in N. Press START button
and shift to P
This message is displayed if you try to
turn off the vehicle with the gear in N
(Neutral).
To turn off the vehicle:
1. Press the Engine Start/Stop button.
The button will change to the ON
position.
2. Press the P button to shift to P (Park).
3. Press the Engine Start/Stop button
again, then the vehicle will turn off.
Low key battery
This message is displayed if the battery
of the smart key is discharged while
changing the Engine Start/Stop button to
the OFF position.
Press brake pedal to start engine
This message is displayed if the Engine
Start/Stop button changes to the ACC
position twice by pressing the button
repeatedly without depressing the brake
pedal.
You can start the vehicle by depressing
the brake pedal and then pressing the
Engine Start/Stop button.
Key not in vehicle
This message is displayed if the smart
key is not in the vehicle when you leave
the vehicle with the Engine Start/Stop
button in the ON or Start position.
Always turn off the engine before leaving
your vehicle.
Key not detected
This message is displayed if the smart
key is not detected when you press the
Engine Start/Stop button.
Press START button again
This message is displayed if you were
unable to start the vehicle when the
Engine Start/Stop button was pressed.
If this occurs, attempt to start the engine
by pressing the Engine Start/ Stop button
again.
If the warning message appears each
time you press the Engine Start/Stop
button, we recommend that you have
the vehicle inspected by an authorized
retailer of Genesis Branded products.
004_RS4_HMA.indd 4-212022-04-06  3:02:32

4-26
Instrument Cluster, Armrest touchscreen, Infotainment system
The LCD display modes can be changed by using the control switches.
Switch Operation Function
APress MODE button for changing gauge mode
B
PressSELECT/RESET switch for selecting pop up
SELECT/RESET switch for entering or exiting widget
navigation mode
Press and holdSELECT/RESET switch for selecting certain pop up
SELECT/RESET switch for hiding or showing widget
mode
Press 3 timesSELECT/RESET switch for resetting the selected Normal
view mode
Tap up, down,
left, right When in widget mode, the switch is used to navigate the
widgets.
When not in widget mode, the switch is used to change
to previous or next song.
C, Press UP, DOWN switch for changing View modes
View Modes
View modes Explanation
Driving Assist viewDriving Assist view displays the status of the vehicle’s Driver
Assistance systems
Map view Show map and navigation related information
Normal viewShow trip computer or widget on center without background
information
The information provided may differ depending on which functions are applicable
to your vehicle.
LCD Display Control
ORS041018ORS041018ORS041017 ORS041017
LCD DISPLAY
004_RS4_HMA.indd 4-262022-04-06  3:02:33

4-27
04
ORS042035NORS042035N
Driving Assist, Map and Normal View
modes are displayed in the instrument
cluster.
Normal view is also show in the widget
mode.
Driving Assist view
ORS041026ORS041026
The status of Smart Cruise Control, Lane
Following Assist, Highway Driving Assist,
etc. is displayed when Driving Assist view
is selected.
For more details, refer to each system
information section in chapter 6.
Normal View
In the Normal View, using the (Optical
mouse), you may change through items
in the following order.
ORS042025NORS042025N
Drive info
Trip distance, average fuel economy, and
total driving time are displayed.
The information is combined for each
ignition cycle. However, when the engine
has been OFF for 4 hours or longer the
Drive Info screen will reset.
To manually reset the information, press
the
button three times on the steering
wheel when Drive Info is displayed.
The trip distance, the average fuel
economy, and total driving time will reset
simultaneously.
ORS042029NORS042029N
Since refueling
Trip distance, average fuel economy, and
total driving time after the vehicle has
been refueled are displayed.
To reset manually, press the
button
three times on the steering wheel when
‘Since Refueling’ is displayed.
004_RS4_HMA.indd 4-272022-04-06  3:02:34

4-30
Instrument Cluster, Armrest touchscreen, Infotainment system
Setting Touchscreen
Press Setup from the main menu of the
touchscreen.
Settings for other functions can be
accessed on the left side of the Setup
(
) menu.
• Fragrance (if equipped): Select the
fragrance for pleasant riding. For more
details, refer to “Built in diffuser”
section in chapter 5.
• Seat (if equipped): Select different
seat modes for rear right seat
occupant. For more details, refer to
“Seats” section in chapter 3.
• Rear Wireless Charging (if equipped):
Turn on/off the wireless cellphone
charge function for rear seat
occupants. For more details, refer
to “Wireless smart phone charging
system” section in chapter 5.
• Display: Change the screensaver
timeout setting and screen display
method while using massage buttons
from the rear door.
-Screen Time-out: 15 sec, 30 sec, 1
Min, 2 Min (default),5 Min, 10 Min
-Massage Notification/Status
(if equipped): Massage Screen
(default), Pop-up, OFF
• Graphic Themes: Select the display
theme of the screen.
-Use Audio System's Display Theme
(default)
-User-Set Time : Select between
white and black theme, or set the
screen to change automatically to
white theme during the day and
black during the night. • Illumination: Select the brightness of
the screen.
-Adjust Brightness Automatically:
The brightness of the display is
automatically adjusted depending
on outside brightness.
-Manual adjustment: Manually adjust
the brightness to desired level.
Brightness is maintained at the
adjusted level.
-Reset: Returns all settings to
default.
• Blue Light Filter: Select whether to
turn the blue light filter on or off, and
set the color when the blue light lifter
is on.
-Use Blue light filter/color
adjustment: Select or deselect
whether to use the blue light filter,
and adjusts the display color when
the blue light filter is on.
-Auto: Adjusted blue light filter is
turned on automatically when the
surrounding area is dark.
-User-Set Time: Adjusted blue light
filter turns on at the time set.
004_RS4_HMA.indd 4-302022-04-06  3:02:36

5-57
05
Horn
ORS051038
To sound the horn, press the area
indicated by the horn symbol on your
steering wheel (see illustration). The
horn will operate only when this area is
pressed.
NOTICE
Do not strike the horn severely to
operate it, or hit it with your fist. Do not
press on the horn with a sharp-pointed
object.
Heated Steering Wheel
ORS052037N
While the engine is running, touch the
heated steering wheel icon to warm the
steering wheel.
Manually adjusting temperature
Each time you press the heated steering
icon, the temperature changes as
follows.

[ 2))

5-64
Convenience Features
3. While the HomeLink indicator light S
is flashing orange, press and hold the
hand-held remote button. Continue
pressing the handheld remote button
until the HomeLink indicator light S
light changes from orange to green.
You may now release the handheld
remote button.
4. Wait until your garage door comes
to a complete stop, regardless of
position, before proceeding to the
next steps.
5. Press and release the HomeLink
button you are programming and
observe the indicator light.

[If the indicator light remains solid
green, your device should operate
when the HomeLink button is
pressed. At this point, if your device
operates, programming is complete.

[If the indicator light rapidly
flashes green, firmly press, hold
for two seconds and release the
HomeLink button up to three times
in a row slowly to complete the
programming process. Do not press
the HomeLink button rapidly. At
this point if your device operates,
programming is complete. If the
device does not operate, continue
with step 6.
6. At the garage door opener motor,
(security gate motor, etc.) locate the
“Learn”, “Smart”, “Set” or “Program”
button. This can usually be found
where the hanging antenna wire is
attached to the motor-head unit (see
the device’s manual to identify this
button). The name and color of the
button may vary by manufacturer.
ODL3A040504
ÃA ladder and/or second person may
simplify the following steps.
7. Firmly press and release the “Learn”,
“Smart”, “Set” or “Program” button.
You now have up to 30 seconds in
which to complete the next step.
8. Return to the vehicle and firmly press,
hold for two seconds and release,
the HomeLink button up to three
times in a row slowly. Do not press
the HomeLink button rapidly. As soon
as you see the garage door start to
move, stop pressing any buttons
until a few seconds after the garage
door has come to a complete stop,
regardless of position. At this point,
programming is complete and your
device should operate when the
HomeLink button is pressed and
released.

5-66
Convenience Features
4) Canadian Programming
Canadian radio-frequency laws require
transmitter remote signals to “time-
out” (or quit) after a couple seconds of
transmission, which may not be long
enough for HomeLink to pick up the signal
during programming.
If you live in Canada or you are having
difficulties programming a gate operator
or garage door opener by using the
programming procedures, replace
“Programming a New HomeLink Button”
step 3 with the following:
While the HomeLink indicator light S is
flashing orange, press and release (“cycle”)
your device’s handheld remote every two
seconds until the HomeLink indicator light
S changes from orange to green. You may
now release the hand-held remote button.
Then proceed with “Programming a New
HomeLink Button” step 4.2SHUDWLQJ+RPH/LQN®
 2SHUDWLQJ+RPH/LQNp
ORS052307N
1. Press and release the desired
programmed HomeLink button (M, N
or O).
Information
The HomeLink indicator S should
light green, solid or flashing, and your
programmed device should operate.
If your device does not operate, the
HomeLink programming was not
successful, and you’ll need to reprogram
the button.