2023 GENESIS G80 battery

5-48
Convenience Features
WARNING
Before programming HomeLink® to a
garage door opener or gate operator,
make sure people and objects are out
of the way of the device to prevent
potential harm or damage. Do not
use the HomeLink® with any garage
door opener that lacks the safety
stop and reverse features required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an
object - signaling the door to stop and
reverse - does not meet current U.S.
federal safety standards. Using a garage
door opener without these features
increases the risk of serious injury or
death.
For more information, contact
HomeLink® at www.homelink.com, or
call Home-Link customer support at
1-800-355-3515.
It is also recommended that a new
battery be replaced in the handheld
transmitter of the device being trained
to HomeLink® for quicker training and
accurate transmission of the radio
frequency.
1. Programming HomeLink®
The following steps show how to
program HomeLink. If you have any
questions or are having difficulty
programming your HomeLink buttons,
refer to the HomeLink website or call the
HomeLink customer support toll-free
number. Do this, before going back to
the dealer who sold you the car.

[Visit the HomeLink website at: www.
homelink.com. Then at the top of the
page, choose your vehicle make. Then
watch the You Tube video, and/or
access additional website information.

[If you choose to access the website
via your cell phone, scan the QR code.

[Or, call HomeLink customer support
at 1-800-355-3515 (Please have the
vehicle make/model AND the opener
device make/model readily available.)

5-49
05
1) Programming Preparation
OJX1050293N
1. When programming a garage door
opener, it is advised to park the
vehicle outside of the garage.
2. It is recommended that a new battery
be placed in the handheld transmitter
of the device being programmed to
HomeLink for quicker training and
accurate transmission of the radio-
frequency signal.
3. Place the ignition switch to the
ON position for programming of
HomeLink.
2) Programming a New HomeLink®
OJWEV051282N
1. Press and release the HomeLink
button (1), (2) or (3), you would like
to program. The HomeLink indicator
light (7) will flash orange slowly (if
not, perform the steps of “Erasing
+RPH/LQN%XWWRQV
VVHFWLRQDQGVWDUW
over).
OJX1050295N
2. Position the garage door opener
remote 1 – 3 inches (2 – 8cm) away
from the HoleLink buttons.
3. While the HomeLink indicator light (7)
is flashing orange, press and hold the
hand-held remote button. Continue
pressing the handheld remote button
until the HomeLink indicator light (7)
light changes from orange to green.
You may now release the handheld
remote button.
4. Wait until your garage door comes
to a complete stop, regardless of
position, before proceeding to the
next steps.
5. Press and release the HomeLink
button you are programming and
observe the indicator light.

[If the indicator light remains solid
green, your device should operate
when the HomeLink button is
pressed. At this point, if your device
operates, programming is complete.

[If the indicator light rapidly
flashes green, firmly press, hold
for two seconds and release the
HomeLink button up to three times
in a row slowly to complete the
programming process. Do not press
the HomeLink button rapidly. At
this point if your device operates,
programming is complete. If the
device does not operate, continue
with step 6.

5-59
05
NOTICE
The electric type outside rearview
mirror operates even though the Start/
Stop button is in the OFF position.
However, to prevent unnecessary
battery discharge, do not adjust the
mirrors longer than necessary while the
vehicle is not running.
NOTICE
Do not fold the electric type outside
rearview mirror by hand. It could cause
motor failure.
Reverse Parking Aid (if equipped)
ORG3EV051027
When the gear is shifted to the R
(Reverse) position, the side view mirror(s)
will rotate downwards to aid with driving
in reverse.
The state of the side view mirror button
(1) determines whether or not the mirrors
will move:
How it works

[When the L or R button (1) is pressed
(indicator lights ON), both side view
mirrors will move.

[If the L and R buttons (1) are not
pressed (indicator lights OFF), both
side view mirrors will not move.
The side view mirrors will automatically
revert to their original positions if any of
the following occur:

[The Start/Stop button is pressed to
either the OFF position or the ACC
position.

[The gear is shifted to any position
except R (Reverse).

[The side view mirror adjustment
button is not selected.

5-68
Convenience Features
Emergency trunk safety release
ORG3EV051049
Your vehicle is equipped with an
Emergency Trunk Safety Release lever
located inside the trunk. When someone
is inadvertently locked in the trunk, the
trunk can be opened by moving the lever
in the direction of the arrow and pushing
the trunk open.
WARNING

[You and your passengers must
be aware of the location of the
Emergency Trunk Safety Release
lever in this vehicle and how to open
the trunk in case you are accidentally
locked in the trunk.

[
[1(9(5DOORZDQ\RQHWRRFFXS\WKH
trunk of the vehicle at any time. If the
trunk is partially or totally latched
and the person is unable to get out,
serious injury or death could occur
due to lack of ventilation, exhaust
fumes and rapid heat build-up, or
because of exposure to cold weather
conditions. The trunk is also a highly
dangerous location in the event of a
crash because it is not a protected
occupant space but is a part of the
vehicle’s crush zone.

[Your vehicle should be kept locked
and the Smart Key should be kept
out of the reach of children. Parents
should teach their children about the
dangers of playing in trunks.

[Use the release lever for emergencies
only.
Trunk release lever
ORG3EV051050N
When the vehicle battery is discharged or
the trunk needs to be opened manually:
1. Open the cover (1) at the center of the
rear seat. Pull the lever on the back of
the cover all the way.
ORG3EV051092
2. With the lever pulled to the end, fix
the lever (3) on the projecting part (2).
3. Lift and open the trunk manually.
4. Remove the inserted lever to close the
trunk.
WARNING
Make sure to at least have minimum
space at the back and in the upper area
of the trunk when opening or closing
the trunk. If not, the trunk may hit the
surrounding objects (wall, ceiling,
vehicle, etc.) and result in damaging the
vehicle or injuring the person near.

5-69
05
Power Trunk (if equipped)
Power trunk operating conditions
The power trunk operates when vehicle
speed is below 1.8 mph (3 km/h).
WARNING

[Never leave children or animals
unattended in your vehicle. Children
may operate the power trunk. Doing
so can result in injury to themselves
or others and can damage the
vehicle.

[Make sure there are no people or
objects and enough space around
the trunk before operating the
power trunk or smart trunk prior to
use. Serious injury, damage to the
vehicle or damage to surrounding
objects (for example, walls, ceilings,
vehicles, etc.) may result if contact
with the trunk occurs.

[Make sure there are no people or
objects around the trunk before
operating the power trunk. Wait until
the trunk is opened fully and stopped
before loading or unloading cargo
from the vehicle.

[Always keep the trunk lid completely
closed while the vehicle is in motion.
If it is left open or ajar, poisonous
exhaust gases containing carbon
monoxide (CO) may enter the vehicle
and serious illness or death may
result.
NOTICE

[Do not close or open the power
trunk manually. This may cause
damage to the power trunk. If it is
necessary to close or open the power
trunk manually when the battery is
discharged or disconnected, do not
apply excessive force.

[Do not operate the power trunk
more than 10 times continuously
when the (
) indicator is off. Use
the power trunk with the ()
indicator on when the power trunk is
used repeatedly to prevent battery
discharge.

[Do not leave the trunk open for a
long period of time. This may drain
the battery.

[Do not modify or repair any part of
the power trunk by yourself. This
must be done by an authorized
retailer of Genesis Branded products.

[Do not operate the power trunk
under the following conditions.
The power trunk may not operate
properly.
-One side of the vehicle is lifted to
inspect the vehicle or change a tire
-Parking on an uneven road such as
a slope, etc.

[Close the trunk completely and lock
all doors and trunk using the central
door lock button before using an
automatic car wash.

[Do not spray high pressure water
directly on the power trunk outside
open/close button. The trunk may
open unintentionally.

5-74
Convenience Features
Resetting the power trunk
In some circumstances resetting the
power trunk operation may need to
be performed. Some instances where
resetting the power trunk may be
required include:

[When the 12-volt battery is recharged

[When the 12-volt battery is reinstalled
after removal or replacement

[When the related fuse is reinstalled
after removal or replacement
1. With the vehicle off or running, put
the gear in P (Park).
2. While Pressing the power trunk close
inner button, press the power trunk
open outer button for more than 3
seconds. A chime will sound.
3. Slowly close the trunk manually.
4. Press the power trunk open outer
button. The trunk will open with a
chime sound. Wait until the trunk
fully opens to complete resetting. If
the trunk stops before it is fully open,
resetting cannot be completed.
Information
If the power trunk does not operate
properly after the above procedure, have
the system inspected by an authorized
retailer Genesis Branded products.
Emergency trunk safety release

[Inside the trunk
ORG3EV051049Your vehicle is equipped with an
emergency trunk safety release lever
located inside the trunk. When someone
is inadvertently locked in the trunk, the
trunk can be opened by moving the lever
in the direction of the arrow and pushing
the trunk lid to open.

[Inside the vehicle
Follow the below procedure to open
the trunk manually when the battery is
discharged or when there is a problem
with the vehicle:
ORG3EV051050N
1. Open the pass through cover M at the
center of the rear seat.
2. Pull trunk release lever the all the way
back that is located behind the left
side of the pass through cover.

5-89
05
WARNING
Do not use the interior lights when
driving in the dark. The interior lights
may obscure your view and cause an
accident.
NOTICE
Do not use the interior lights for
extended periods when the vehicle is
turned off or the battery will discharge.
Interior lamp AUTO cut
The interior lamps will automatically go
off approximately 20 minutes after the
vehicle is turned off and the doors are
closed. If a door is opened, the lamp
will go off 25 minutes after the vehicle
is turned off. If the doors are locked by
the smart key and the vehicle enters the
armed stage of the theft alarm system,
the lamps will go off five seconds later.
Front lamps
ORG3EV051060L
Front map lamp ():
Touch either icons to turn the map lamp
on or off. This light produces a spot
beam for convenient use as a map lamp
at night or as a personal lamp for the
driver and the front passenger.
Front door lamp ():
The front or rear room lamps come on
when the front or rear doors are opened.
When doors are unlocked by the smart
key, the front and rear lamps come on
for approximately 30 seconds as long as
any door is not opened. The front and
rear room lamps go out gradually after
approximately 30 seconds when the
door is closed. However, if the Start/Stop
button is in the ON position or all doors
are locked, the front and rear lamps will
turn off. If a door is opened with the
Start/Stop button in the ACC position
or the OFF position, the front and rear
lamps will stay on for about 5 minutes.
Front room lamp ()
Press the button to turn ON the room
lamp for the front/rear seats.
INTERIOR LIGHTS

5-100
Convenience Features
Information
ORG3EV051068
Never place anything near the ambient
OLJKWVRODUVHQVRUWRHQVXUHEHWWHUFRQWURO
of the heating and cooling system.
Manual Temperature Control
Mode
The heating and cooling system can be
controlled manually by pushing buttons
other than the AUTO button. In this case,
the system works sequentially according
to the order of buttons selected.
When pressing any button except the
AUTO button while using automatic
operation, the functions not selected will
be controlled automatically.1. Start the vehicle.
2. Set the mode to the desired position.
To improve the effectiveness of
heating and cooling, select the mode
according to the following:
-Heating:
-Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to Fresh or
Recirculation mode.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn the
air conditioning system on.
7. Press the AUTO button to revert
back to full automatic control of the
system.
The climate control system settings
will be maintained, even when the
vehicle is turned OFF. However, the
climate control system settings will be
initialized when the battery has been
discharged, or when the cables have
been disconnected.
In this case, adjust the climate control
system settings again.