2023 GENESIS G70 sensor

Emergency Situations8-24
OIGH067043
OIK082011N
11. After driving approximately 4~6 miles (7~10 km or about 10 min), stop at a
safety location.
12. Connect the filling hose (3) of the compressor directly to the tire valve.
13. Plug the compressor power cord into the vehicle power outlet.
14. Adjust the tire inflation pressure to the recommended tire inflation.
With the ignition switched on,
proceed as follows.

- To increase the inflation pressure
: Switch on the compressor. To
check the current inflation pressure
setting, briefly switch off the
compressor.

- To reduce the inflation pressure:
Press the button (9) on the
compressor.
NOTICE
Do not let the compressor run for more
than 10 minutes, otherwise the device
will overheat and may be damaged.
Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tire reading,
the compressor needs to be turned off.
CAUTION
If the inflation pressure is not
maintained, drive the vehicle a second
time, refer to step 10.
Then repeat steps 11 to 14.
Use of the TMK may be ineffectual for
tire damage larger than approximately
0.16 in (4 mm).
Have you contact an authorized retailer
of Genesis Branded products if the tire
cannot be made roadworthy with the
Tire Mobility Kit.
WARNING
The tire inflation pressure must be at
least 32 psi (220 kPa). If it is not, do not
continue driving.
Call for road side service or towing.
CAUTION
Tire pressure sensor
(if equipped with TPMS)
The sealant on the tire pressure sensor
and wheel should be removed when
you replace the tire with a new one and
inspect the tire pressure sensors at an
authorized dealer.
Information
hen reinstalling the repaired or replaced
tire and wheel on the vehicle, tighten the
wheel lug nut to ~ lbf ft (11~13 kgf m).

08
8-27
WARNING
If your vehicle is equipped with a
rollover sensor, press the Engine Start/
Stop button to the OFF or ACC position
when the vehicle is being towed.
The side impact and curtain air bag
may deploy if the sensor detects the
situation as a rollover.
When towing your vehicle in an
emergency without wheel dollies:
1. Place the shift lever in N (Neutral).
2. Release the parking brake.
NOTICE
Failure to place the shift lever in N
(Neutral) when being towed with the
front wheels on the ground can cause
internal damage to the transmission.
Removable Towing Hook
1. Open the trunk, and remove the towing hook from the tool case.
„Front
OIK080017
„Rear
OIK080019
2. Remove the hole cover by pressing the lower part of the cover on the
bumper.
3. Install the towing hook by turning it clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install the cover after use.

Maintenance9-52
Fuse Name Fuse Rating Circuit Protected
DOOR LOCK 20
A Door Lock Relay, Door Unlock Relay, Dead Lock Relay
SEAT HEATER 25AFront Air Ventilation Seat Control Module
Front Seat Warmer Control Module
TRUNK 10A Trunk Lid Relay, Fuel Lid Relay, Crash Pad Switch
IBU2 10A IBU, Rain Sensor
AIR BAG2 15A SRS Control Module
POWER OUTLET1 20A Front Power Outlet
MODULE8 10A Cooling Fan Controller (BLDC Motor)
MODULE7 10ADosing Control Module, AWD ECM, Active Air Flap LH,
ECS Unit, Front View Camera, Console Switch, Crash
Pad Switch, IBU, Console Switch, Front View Camera,
Front Wireless Charger, Steering Tilt & Telescopic
Module, Surround View Monitor ECU, Electronic Control
Engine Mounting Module, Steering Angle Sensor
POWER HANDLE 15A Steering Tilt & Telescopic Module
MODULE9 10A Driver Air Lumbar Control Unit
MODULE1 10AData Link Connector, Console Switch, Hazard
Switch, Electronic Control Engine Mounting Module
CHARGER 10A Front/Rear USB Charger, Front Tray USB Charger
MODULE5 10AA/C Control Module, A/C Switch, A/V & Navigation
Head Unit, Low DC-DC Converter (Audio/AMP), Electro
Chromic Mirror, AMP, Emergency Module, Driver IMS
Control Module, Front Air Ventilation Seat Control
Module, Data Link Connector, Front/Rear Seat Warmer
Control Module, IFS Module
SUNROOF 20A Sunroof Control Unit (Glass)
PASSENGER P/ WINDOW 25APassenger Safety Power Window Module, Rear Power
Window Switch RH, Rear Safety Power Window Module
RH
POWER
OUTLET2 20A [5DR] Rear Power Outlet

09
9-53
Fuse NameFuse Rating Circuit Protected
WASHER 15A
Multifunction Switch
MDPS 10A MDPS Unit
DRIVER P/SEAT 30A Driver IMS Control Module, Driver Seat Manual Switch
PASSENGER P/SEAT 30A
Passenger Seat Manual Switch, Passenger Walk In Relay
Module
DRIVER
P/WINDOW 25A
Driver Safety Power Window Module, Rear Safety Power
Window Module LH, Rear Power Window Switch LH
MODULE6 10ASurround View Monitor ECU, IBU, Emergency Call
Module, AMP, Electronic ATM Shift Lever, Overhead
Console Lamp, A/V & Navigation Head Unit, Low DC-DC
Converter (Audio/AMP)
A/CON 10AA/C Control Module, A/C Switch, PM Sensor (A/C), E/R
Junction Block (RLY.6), Diesel Junction Block (RLY.3/4)
MODULE4 10AHead Lamp LH/RH, Auto Head Lamp Leveling Device
Module

09
9-57
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
ESC3 10
A ESP Control Module
ECU3 10A ECM
ECU2 15A ECM
HORN 20A Horn Relay
WIPER1 30A Wiper Power Relay
TCU2 15A P/N Relay, TCM
SENSOR4 10AElectronic Oil Pump Module, Brake Vacuum Switch, E/R
Junction Block (RLY.1 (Brake Vacuum Relay))
TCU1 20A TCM
WIPER2 10A IBU, ECM
SENSOR1 15ARear Sub Junction Block (Fuel Pump Relay),
[D4HB] Rail Pressure Regulating Valve, DieseL Junction
Block (RLY.1 (Fuel Filter Heater Relay))
SENSOR5 20A[G4KL] Ignition Coil #1/#2/#3/#4
[G6DP] Ignition Coil #1/#2/#3/#4/#5/#6
[D4HB] Electronic Water Pump
MODULE 10A Active Air Flap LH
SENSOR1 10A[D4HB] Glow Relay Unit, Fuel Heater & Water Separator
Sensor
ECU1 20A ECM
SENSOR3 15A[G4KL] Oxygen Sensor (Up/Down)
[G6DP] Oxygen Sensor #1/#2/#3/#4
[D4HB] Lambda Sensor #1/#2, Electronic VGT Actuator,
Fuel Metering Unit, EGR Cooing Bypass Solenoid
Vlave, PTC Heater, Mid Nox Sensor, PM Sensor,
Rear Nox Sensor

Maintenance9-58
Fuse Name Fuse Rating Circuit Protected
SENSOR2 10
AE/R Junction Block (RLY. 9 - Cooling Fan Relay),
[G4KL] Electronic Thermostat, Oil Control Valve, Purge
Control Solenoid Valve, Recirculation Control
Solenoid Valve
[G6DP] Electronic Thermostat, Oil Pressure Solenoid Valve, Oil Control Valve #1/#2/#3/#4 (Intake/
Exhaust), Recirculation Control Solenoid Valve,
Purge Control Solenoid Valve, Variable Exhaust
Flap Actuator LH/RH
[D4HB] Oil Pump Solenoid Valve, Air Flow Sensor,
Crankshaft Position Sensor, Front Nox Sensor, Oil
Level Sensor, Stop Lamp Switch
B/ALARM 10A E/R Junction Block (RLY. 2 - Burglar Alarm Horn Relay)
Relay
Type Relay No. Relay Name
MICRO RLY. 1 Vacuum OIK090033
MICR

O RLY. 2 Burglar Alarm Horn Relay
MICRO RLY. 6 Blower Relay
MICRO RLY. 7 Start Relay
MICRO RLY. 8 E-CVVT Relay (G4KL) MINI RLY. 9 Cooling Fan Relay

Maintenance9-62
Battery box fuse panel
Fuse Name Fuse Rating Circuit Protected
B+1 100A R
ear Sub Junction Block
(ACC Relay, Fuse - F7, F12, F13, F16, F17)
B+2 100A Rear Sub Junction Block
(DCU Relay, Fuse - F3, F5, F4, F11, F15)
START 40A E/R Junction Block (Fuse - F3),
PCB Block (Fuse - F3, F9)
AMS 10A Battery Sensor

Maintenance9-68
APPEARANCE CARE
Exterior CareNOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp or
side view mirrors might be damaged
due to sunlight reflected from the
sign or building. To prevent damage of
the exterior plastic parts, you should
avoid parking in areas where light may
be reflected or use a car cover. (The
exterior plastic parts applied to your
vehicle may vary.)
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
ashing
To help protect your vehicle’s finish from
rus
t and deterioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish. igh-pressure washing

[ When using high-pr
essure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

[ Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.

[ Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.