2023 CITROEN C3 lock

36
Practical information
Do not open the bonnet under very windy
conditions.
Cooling of the engine when stopped
The engine cooling fan may start after
the engine has been switched off.
Take care with objects or clothing that
could be caught in the blades of the fan!
Water washing in the engine
compartment including high pressure
water washing may cause the failure of
electrical circuits located in the engine
compartment.
Never allow water or other liquids to come in
contact with electrical/electronic components
inside the vehicle as this may damage them.
Opening

► Pull the release lever towards you.

► Lift the safety catch and raise the bonnet.

► Unclip the stay from its housing and place it
in the support slot to hold the bonnet open.
Closing
► Take the stay out of the support slot.
► Clip the stay in its housing.
►

Lower the bonnet and release it near the end
of its travel.
►


Pull on the bonnet to check that it is locked
correctly

.
Engine compartment
The engines represented are examples given for
illustration purposes only.
The locations of the following elements may
vary:

41
Practical information
7Timing and accessory kits
Timing and accessory kits are used from
the time the engine is started until it is
switched off. It is normal for them to wear over
time.
A
faulty timing or accessory kit can damage
the engine, rendering it unusable. Observe the
recommended replacement frequency, stated in
distance travelled or time elapsed, whichever is
reached first.
Advice on care and maintenance
General recommendations
Observe the following recommendations to avoid
damaging the vehicle.
Exterior
Never use a high-pressure jet wash in
the engine compartment - risk of
damaging the electrical components!
Do not wash the vehicle in bright sunshine or
extremely cold conditions.
When washing the vehicle in an
automatic roller-brush car wash, be sure
to lock the doors.
When using a pressure washer, hold the
lance at least 30 cm from the vehicle
(particularly when cleaning areas containing
chipped paint, sensors or seals).
Promptly clean up any stains containing
chemicals liable to damage the vehicle's paint
(including tree resin, bird droppings, insect
secretions, pollen and tar).
If justified by the environment, clean the
vehicle more frequently to remove salty
deposits (in coastal areas), soot (in industrial
areas) and mud (in wet or cold areas). These
substances can be highly corrosive.
Contact a CITROËN dealer for advice on
removing stubborn stains requiring special
products (such as tar or insect removers).
Preferably, have paint touch-ups performed
by a CITROËN dealer.
The versions provided with roof rails are not designed for fitting roof racks. It is
only for aesthetic factor.
Do not apply loads on the roof rails.
Interior
When washing the vehicle, never use a
water hose or high-pressure jet to clean
the interior.
Liquids carried in cups or other open
containers can spill, presenting a risk of
damage if they come into contact with the
controls in the dashboard and centre console.
Be vigilant!
Bodywork
High-gloss paint
Do not use abrasive products, solvents,
petrol or oil to clean the bodywork.
Never use an abrasive sponge to clean
stubborn stains - risk of scratching the
paintwork!
Do not apply polish in strong sunshine, or to
plastic or rubber parts.
Use a soft cloth and soapy water or a pH
neutral product.
Gently wipe the bodywork with a clean
microfibre cloth.
Apply polish with the vehicle clean and dry.
Comply with the instructions for use stated on
the product.

42
In the event of a breakdown
Tool kit
Set of tools supplied with the vehicle.
Accessing the tools

The tools are located under the boot floor carpet,
with the spare wheel.
List of tools

1.Jack
To raise the vehicle.
2.Jack handle
3. Wheel wrench
To remove the wheel bolts.
4. Removable towing eye
For more information on Towing the vehicle
and using the removable towing eye, refer to the
corresponding section.
These tools are specific to the vehicle and may vary according to the level of
equipment.
Do not use them for any other purpose.
The jack must only be used to change a wheel with a damaged or punctured tyre.
Do not use any jack other than the one
supplied with the vehicle.
If the vehicle does not have its original jack,
contact a CITROËN dealer.
The jack does not require any maintenance.
Spare wheel
Access to the spare wheel
The spare wheel is installed in the boot, under
the floor carpet.
Removing the spare wheel

► Rotate the fixing screw to unlock the spare
wheel.
►

Lift the spare wheel towards you from the
rear

.
►

T
ake the wheel out of the boot.
Removing the jack

► Rotate the fixing screw to unlock the jack on
one end.
►

T
ilt the jack towards the right and lift it from
the rear.

43
In the event of a breakdown
8Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does
not obstruct traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear to
lock the wheels, apply the parking brake and
switch off the ignition.
Check for the fixed illumination of the parking
brake indicator lamps in the instrument panel.
The occupants must get out of the vehicle
and wait where they are safe.
If necessary, place a chock under the wheel
diagonally opposite the wheel to be changed.
Never go underneath a vehicle raised using a
jack; use an axle stand.
Wheel with wheel trim
When removing the wheel , first remove
the wheel trim by pulling at the valve aperture.
When refitting the wheel , refit the wheel
trim, starting by placing its aperture in line
with the valve and then pushing it into place
all round its edge with the palm of your hand.
Wheel nuts removing pattern

► Loosen the nuts on the wheel in diagonal
sequence. Do not remove wheel nuts.


► Slacken the bolts using the wheel wrench 3
only.


► Place the foot of jack 1 on the ground and
ensure that it is directly below the front A or
rear
B jacking point on the underbody, whichever
is closest to the wheel to be changed.


► Extend jack 1 with the jack handle 2 and
wheel wrench 3 until its head comes into contact
with jacking point

A
or B; contact area A or B
on the vehicle must be properly inserted into the
central part of the head of the jack.
►

Raise the vehicle until there is sufficient
space between the wheel and the ground to
admit the spare (not punctured) wheel easily

.

45
In the event of a breakdown
8► Tighten the spare wheel fixing screw by a few
turns.
After changing a wheel
The temporary spare wheel is only intended for temporary emergency use,
until the conventional wheel can be repaired
or replaced.
Continuous use of this spare can result in tire
failure and loss of control. Always observe
these precautions when using this spare:
–

Y

our vehicle will respond differently with
this temporary spare.
–

Do not exceed 80 km/h speed.
–


Replace this spare with a standard tire and
wheel as soon as possible.
–


Use of this spare will reduce ground
clearance.
–


Set the specified tire pressure indicated
on the tire information label located on the
driver's door lock pillar

.
–

Do not use tire chains on the temporary
spare. If you must use tire chains, rearrange
the wheels so standard tires and wheels are
fitted to the front axle.
–


The temporary spare wheel has a much
shorter tread life than the conventional

wheels
on your vehicle. Replace the tire as soon as
possible as the tread wear indicator appears.
The inflation pressure of the temporary spare
wheel should be checked at least monthly. At
the same time, check that the tire is stored
securely. If it is not, tighten it.
Note that two or more temporary spare
wheels should not be used on one vehicle
simultaneously.
Changing a bulb
In some weather conditions (e.g. low
temperature or humidity), misting on the
internal surface of the glass of the headlamps
and rear lamps is normal, and will disappear
after the lamps have been on for a few
minutes.
The headlamps have polycarbonate lenses with a protective coating:
–

Do not clean them with a dry or abrasive
cloth, nor with detergent or solvent
products.
–


Use a sponge and soapy water or a pH
neutral product.
–


When using a high-pressure washer on
persistent marks, do not keep the lance
directed towards the headlamps, lamps or
their edges for too long, so as not to damage
their protective coating and seals.
Changing a bulb must only be done with
the ignition off and after the headlamp /
lamp has been switched off for several
minutes - risk of serious burns!
Do not touch the bulb directly with your
fingers; use a lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.
Always replace a failed bulb with a new bulb
of the same type and specification. To avoid
lighting imbalance, replace the bulbs in pairs.
Refitting the lamp units
Perform the operations in the reverse
order to dismantling.
Opening the bonnet / Accessing the
bulbs
With the engine warm, proceed with caution -
risk of burns!
Take care with objects or clothing that could
be caught in the blades of the cooling fan -
risk of strangulation!
Halogen bulbs (Hx)
To ensure good quality lighting, check
that the bulb is correctly positioned in its
housing.

46
In the event of a breakdown
Light-emitting diode (LED)
headlamps and lamps
Depending on version, the affected types of
headlamps / lamps are:
–
Daytime running lamps / sidelamps.
–


Direction indicator side repeaters.
–


Third brake lamp.
–


Number plate lamps.
Light emitting diodes (LED)
For the replacement of this type of bulb,
you must contact a CITROËN dealer.
Do not touch the LED technology lamps - risk
of electrocution!
Front lamps
Model 1

1. Daytime running lamps/sidelamps (W5W
bulb)
2. Direction indicators (PY21W
- 12V - 21W)
3. Beam headlamps (H4
- 12V - 60/55W)
Model 2

1.Daytime running lamps/sidelamps (LED)
2. Direction indicators (PY21W
- 12V - 21W)
3. Beam headlamps (H4
- 12V - 60/55W)
Daytime running lamps/sidelamps

► Turn the bulb holder a quarter of a turn and
pull it out.
►
Pull the bulb out and change it.
Direction indicators
Rapid flashing of a direction indicator
lamp (left or right) indicates that one of
the bulbs on the corresponding side has
failed.


► Turn the bulb holder a eighth of a turn anti-
clockwise and remove it.
►

Remove the bulb and replace it.
Amber coloured bulbs, such as the direction indicators, must be replaced by
bulbs with identical colour and specifications.
Beam headlamps

► Remove the protective cover by pulling on
the tab.
►

Disconnect the bulb connector
.
►

Release the retaining tab.
►


Change the bulb taking care to align the
metal part with the grooves on the lamp.
►


Reposition the retaining tab.
►


Reconnect the bulb connector
.

47
In the event of a breakdown
8► Ensure that the cover is refitted correctly all
around to ensure correct sealing.
Rear lamps
Model 1

1. Sidelamps / Brake lamps
(P21/5W - 12V - 21W/5W)
2. Direction indicators (PY21W
- 12V - 21W)
3. Reversing lamp (P21W
- 12V - 21W)
Model 2

1.Sidelamps / Brake lamps
(P21/5W - 12V - 21W/5W)
2. Direction indicators (PY21W
- 12V - 21W)
3. Reversing lamp (P21W
- 12V - 21W)
4. Additional sidelamps (W3W
- 12V - 3W)
5. Connecting tail lamps (W3W
- 12V - 3W)
Changing bulbs
These bulbs are changed after removing the tail
lamp assembly.
►
Open the boot.
►


Unscrew the nut and remove it. Be careful
not to drop it inside the wing.
►


Unclip the lamp unit and carefully extract it
pulling straight towards the outside.
A

standard pair of pliers or the wheel wrench
(depending on equipment) may be necessary to
remove the nut.
Sidelamps/Brake lamps / Reversing lamp /
Direction indicators


► Turn the bulb holder a eighth of a turn anti-
clockwise and remove it.
►

Remove the bulb and replace it.
Additional sidelamps / Connecting tail
lamps (if equipped)


► Turn the bulb holder a quarter of a turn and
pull it out.
►
Pull the bulb out and change it.
Interior lighting
Courtesy lamp (10W - 12V - 10W)

► Using a thin, flap tip screwdriver , unclip the
entire console surrounding the courtesy lamp.
►

Remove the defective bulb and replace it.
►


Fit the console back into place around the
courtesy lamp and clip it correctly

.

59
In the event of a breakdown
8When towing a vehicle with all four wheels on
the ground, always use an approved towing
arm; rope and straps are prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
A professional towing service must be
called if:
–

Broken down on a motorway or main road.
–


Not possible to put
the gearbox into neutral,
unlock the steering, or release the parking
brake.
–

T

owing with only two wheels on the ground.
–

No approved towbar available.
Access to the tools

The towing eye is stored under the boot floor
carpet.
Towing your vehicle
To access the front screw thread:

► Remove the cover .
To be towed:
►

Screw the towing eye in fully
.
►

Install the towbar
.
►

Put the gearbox into neutral.
Failure to observe this instruction could
result in damage to certain components
(braking, transmission, etc.) and to the
absence of braking assistance the next time
the engine is started.
►

Unlock the steering and release the parking
brake.
►


Switch on the hazard warning lamps on both
vehicles.
►


Move off gently
, drive slowly and only for a
short distance.