2022 YAMAHA YFM90R engine

9-34
9
EBU25248Replacing the fuseIf an electrical problem is suspected, check the
fuse and replace it if necessary as follows.NOTICEECB00641To prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse. 1. Turn off all electrical systems. (See page 5-1.)
2. Remove the seat. (See page 5-13.)3. Remove the blown fuse, and then install a
new fuse of the specified amperage.
WARNING! Always use a fuse of the spec- ified rating, and never use a substitute ob-
ject in place of the proper fuse. An
improper fuse or a substitute object can
cause damage to the electrical system,
which could lead to a fire.
[EWB02173]
4. Turn on the main switch and start the engine.
5. Install the seat.
6. If the fuse immediately blows again, have a Yamaha dealer check the vehicle.EBU34030Removing a wheel1. Place the ATV on a level surface.
2. Loosen the wheel bolts.
1. Fuse
2. Spare fuse
2 1
Specified fuseW
7.5 A
UBD366E0.book Page 34 Thursday, June 10, 2021 2:39 PM

9-37
9
EBU25754Troubleshooting chart
Check the fuel level in
the fuel tank.1. Fuel
There is enough fuel.There is no fuel.
Check the battery.
Supply fuel.
The engine does not start.
Check the battery.
The engine does not start.
Check the ignition.
Operate the electric starter.4. Compression
There is compression.
There is no compression.
The engine does not start. Have a Yamaha dealer check the ATV.Have a Yamaha dealer check the ATV.
Remove the spark plug
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug. Have a Yamaha dealer check the ATV.
The engine does not start.
Check the compression.
Operate the electric starter.2. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.Check the battery lead connections,
and have a Yamaha dealer charge
the battery if necessary.
DryWet
Open the throttle halfway and operate
the electric starter.
UBD366E0.book Page 37 Thursday, June 10, 2021 2:39 PM

10-1
10
EBU25861
CLEANING AND STORAGE
EBU25904CleaningFrequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.1. Before cleaning the ATV: a. Block off the end of the exhaust pipe toprevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps are properly installed.
2. If the engine case is excessively greasy, apply degreaser with a paint brush. Do not apply
degreaser to the chain, sprockets or wheel
axles.
3. Rinse the dirt and degreaser off with a garden hose. Use only enough pressure to do the
job. WARNING! Wet brakes may have re-
duced stopping ability, increasing the
chance of an accident. Test the brakes af-
ter washing. Apply the brakes several
times at slow speeds to let friction dry out
the linings.
[EWB02312]
NOTICE: Excessive wa- ter pressure may cause water seepage
and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high-pressure de-
tergent applications such as those avail-
able in coin-operated car washers.
[ECB00712]
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or
bottle brush is handy for hard-to-reach plac-
es.
5. Rinse the ATV off immediately with clean wa- ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Dry the chain and lubricate it to prevent it from rusting.
7. Clean the seat with a vinyl upholstery cleaner to keep the cover pliable and glossy.
8. Automotive type wax may be applied to all painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
UBD366E0.book Page 1 Thursday, June 10, 2021 2:39 PM

10-2
10abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.
9. If the headlight lens has fogged up, start the engine and turn on the headlight to help re-
move the moisture.
EBU30362StorageShort-term
Always store your ATV in a cool, dry place and, if
necessary, protect it against dust with a porous
cover. NOTICE: Storing the ATV in a poorly ven-
tilated room or covering it with a tarp while it is
still wet, will allow water and humidity to seep
in and cause rust. To prevent corrosion, avoid
damp cellars, stables (because of the presence
of ammonia) and areas where strong chemi-
cals are stored.
[ECB00722]
Long-term
Before storing your ATV for several months: 1. Make any necessary repairs and perform all outstanding maintenance.
2. Follow all the instructions in the Cleaning sec- tion of this chapter. 3. Fill up the fuel tank and add fuel stabilizer (Fu-
el Med Rx if available), and then run the en-
gine for 5 minutes to distribute the treated
fuel.
4. Turn the fuel cock lever off, and then drain the carburetor float chamber by loosening the
drain bolt. Pour the drained fuel into the fuel
tank.
5. Perform the following steps to protect the en- gine from internal corrosion.a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place the spark plug on the
cylinder head so that the electrodes are
grounded. (This will limit sparking during
the next step.)
d. Turn the engine over several times with the starter. (This will coat the cylinder wall
with oil.)
Specified amount:
7.5 ml per liter of fuel (1 oz per gallon)UBD366E0.book Page 2 Thursday, June 10, 2021 2:39 PM

11-1
11
EBU25964
SPECIFICATIONS
Dimensions:Overall length:1485 mm (58.5 in)
Overall width: 1020 mm (40.2 in)
Overall height:
955 mm (37.6 in)
Wheelbase: 1030 mm (40.6 in)
Ground clearance: 210 mm (8.3 in)Weight:Curb weight:126.5 kg (279 lb)Loading:Maximum load:
82.0 kg (181 lb)
(Total weight of rider, cargo, accessories, and tongue)Noise and vibration level:Noise level (77/311/EEC):73.0 dB(A) at 3500 r/min
Uncertainty of measurement: 0.4 dB(A)
Vibration on seat (EN1032, ISO5008):
1.5 m/s²
Uncertainty of measurement: 0.3 m/s² Vibration on handle (EN1032, ISO5008):
5.2 m/s²
Uncertainty of measurement: 1.3 m/s²
Engine:Combustion cycle:
4-stroke
Cooling system: Air cooled
Valve train: SOHC
Number of cylinders:
Single cylinder
Displacement: 90 cm³
Bore × stroke:
47.0 × 51.8 mm (1.85 × 2.04 in)
Starting system:
Electric starter and kickstarterEngine oil:Recommended brand:
SAE viscosity grades:5W-30, 10W-30, 10W-40, 15W-40, 20W-40, 20W-50
UBD366E0.book Page 1 Thursday, June 10, 2021 2:39 PM

11-2
11
Recommended engine oil grade:API service SG type or higher, JASO standard MA
Quantity: Oil change:0.80 L (0.85 US qt, 0.70 Imp.qt)Transmission oil:Type:
SAE 80W-90
Quantity: 0.35 L (0.37 US qt, 0.31 Imp.qt)Fuel:Recommended fuel:
Regular unleaded gasoline (Gasohol [E10] acceptable)
Minimum research octane: 91
Fuel tank capacity: 6.6 L (1.7 US gal, 1.5 Imp.gal) Fuel reserve amount:
0.9 L (0.24 US gal, 0.20 Imp.gal)
Carburetor:Type × quantity:
H66D16 × 1Front tire:Size:
AT18 x 7-8
Manufacturer/model:
DURO/DI2017Rear tire:Size:AT18 x 9-8
Manufacturer/model:
DURO/DI2016Front brake:Type:Mechanical leading, trailing drum brakeRear brake:Type:Mechanical leading, trailing drum brakeFront suspension:Type:
Swing axleRear suspension:Type:SwingarmElectrical system:System voltage:12 V
0 10 30 50 70 90 110 130 ˚F
–20 –10 0 10 20 30 40 50 ˚CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
UBD366E0.book Page 2 Thursday, June 10, 2021 2:39 PM

11-3
11
Battery:Model:GTX5L-BS
Voltage, capacity:
12 V, 4.0 AhEBU30403Noise and vibration levels statement (for Eu-
rope)
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
EBU38670CO2 emissions levels statement (for Europe)
This CO2 measurement results from testing over a
fixed test cycle under laboratory conditions a(n)
(parent) engine representative of the engine type
(engine family) and shall not imply or express any
guarantee of the performance of a particular en-
gine.
UBD366E0.book Page 3 Thursday, June 10, 2021 2:39 PM

12-1
12
INDEX
AAccessories and loading ................................................ 7-6
Air filter element, cleaning ........................................... 9-15BBattery ......................................................................... 9-31
Brake lever free play, adjusting the front ..................... 9-23
Brake lever free play (rear), adjusting .......................... 9-24
Brake lever, front ........................................................... 5-5
Brake lever, rear ............................................................. 5-5
Brake levers, checking and lubricating ........................ 9-28
Brakes .......................................................................... 9-21
Brakes, front and rear .................................................... 6-3CCables, checking and lubricating ................................ 9-28
Carburetor, adjusting ................................................... 9-19
Chassis fasteners .......................................................... 6-6
Cleaning ....................................................................... 10-1DDrive chain ..................................................................... 6-3
Drive chain, lubricating ................................................ 9-27
Drive chain slack .......................................................... 9-25
Drive select lever ........................................................... 5-6
Drive select lever and driving in reverse ........................ 7-3EEngine break-in .............................................................. 7-4
Engine, cold start ........................................................... 7-1
Engine idling speed ..................................................... 9-19
Engine oil ..............................................................6-3, 9-10
Engine, starting a warm ................................................. 7-3Engine stop switch ........................................................ 5-2
FFront and rear brake shoes, checking ......................... 9-21
Front arm pivots, lubricating ........................................ 9-29
Front knuckle pivots, lubricating ................................. 9-30
Fuel ......................................................................... 5-9, 6-3
Fuel cock ..................................................................... 5-10
Fuel tank cap ................................................................. 5-8
Fuse, replacing ............................................................ 9-34HHandlebar switches ....................................................... 5-2IIdentification numbers ................................................... 1-1
Indicator lights ............................................................... 5-1
Instruments and switches .............................................. 6-6KKickstarter ...................................................................... 5-7LLabel locations ............................................................... 2-1MMain switch .................................................................... 5-1
Maintenance chart, emission control system ................ 9-3
Maintenance chart, general maintenance and
lubrication .................................................................... 9-5
Model label .................................................................... 1-1NNeutral indicator light .................................................... 5-1OOwner’s Manual and tool kit .......................................... 9-2
UBD366E0.book Page 1 Thursday, June 10, 2021 2:39 PM