2022 YAMAHA XSR 900 change time

Instrument and control functions
4-4
1
2
345
6
7
8
9
10
11
12
13
position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU66030
Horn switch “ ”
Press this switch to sound the horn.
EAU66061
Stop/Run/Start switch “ / / ”
To crank the engine with the starter, set
this switch to “ ”, and then push the
switch down towards “ ”. See page
6-2 for starting instructions prior to
starting the engine.
Set this switch to “ ” to stop the engine
in case of an emergency, such as when
the vehicle overturns or when the throt-
tle cable is stuck.
EAU91670
Hazard switch “ ”
Use this switch to turn on the hazard
lights (simultaneous flashing of all turn
signal lights). The hazard lights are
used in case of an emergency or to
warn other drivers when your vehicle is
stopped where it might be a traffic haz-
ard.
The hazard lights can be turned on or off only when the key is in the “ON” po-
sition. You can turn the main switch to
the “OFF” or “LOCK” position, and the
hazard lights will continue to flash. To
turn off the hazard lights, turn the main
switch to the “ON” position and operate
the hazard switch again.
NOTICE
ECA10062
Do not use the hazard lights for an
extended length of time with the en-
gine not running, otherwise the bat-tery may discharge.
EAU73952
Cruise control switches
See page 3-1 for an explanation of the
cruise control system.
EAU91365
MODE switches
Use the MODE switches to change the
“D-MODE” and “TCS-MODE” located
on the left side of the main display.
There are three mode controls:
MODE up switch
- press this switch to
change the selected mode setting up-
ward.
“MODE” switch - press this switch to toggle left to right between “D-MODE”
and “TCS-MODE”.
MODE down switch
- press this switch
to change the selected mode setting
downward.
TIP
When in “D-MODE 1”, pressing
the MODE up switch will cycle to
“D-MODE 4”. When in “D-MODE
4”, pressing the MODE down
switch will not cycle to “D-MODE
1”.

The “TCS-MODE” can only be
turned off from the main display.
Select “TCS-MODE” with the
“MODE” switch, then press and
hold the MODE up switch until
“OFF” is displayed.

To turn the traction control system
back on, use the MODE down
switch.

When “TCS-MODE” has been set
to “OFF”, the traction control sys-
tem, SCS and LIF systems are all
turned off together.

See page 4-12 for more informa-
tion on the MODE display.

See page 3-4 for more information
BEA-28199-E0.book 4 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-5
1
2
34
5
6
7
8
9
10
11
12
13 on “TCS-MODE”.

See page 3-3 for more informationon “D-MODE”.
EAU91374
Wheel switch “ ”
When the wheel switch is operated, a
cursor will appear around the previous-
ly selected item on the display.
The wheel switch controls:
Vehicle information displays

Settings MENU

Grip warmer function (Option)
Operate the wheel switch as follows:
Rotate up - rotate the wheel upward to
scroll up or increase a setting value.
Rotate down - rotate the wheel down-
ward to scroll down or decrease a set-
ting value.
Press inward - press the wheel switch
in towards the handlebar to select items
indicated by the cursor and confirm set-
tings changes. Press and hold the
switch inward to reset selected items.
TIP
If the wheel switch is not operated
for a certain period of time, the cur-
sor will disappear.

For items that can be reset, leave
the cursor over the item, press and
hold the switch to reset.

See page 4-9 for more information
on the main screen and its func-
tions.

See page 4-15 for more informa-
tion on the MENU screen and howto make settings changes.
EAU4939U
Indicator lights and warning
lights1. Immobilizer system indicator light “ ”
2. Left turn signal indicator light “ ”
3. Right turn signal indicator light “ ”
4. High beam indicator light “ ”
5. Neutral indicator light “ ”
6. Stability control indicator light “ ”
7. Auxiliary system warning light “ ”
8. ABS warning light “ ”
9. Fuel level warning light “ ”
10.Oil pressure and Coolant temperature warning light “ ”
11.Malfunction indicator light “ ”
12.Cruise control indicator lights “ ” /“ ”
ABS
3
4
56
7
8
11 11
10 10 9
11 1 12
2 2
1012 12 12 9 9
BEA-28199-E0.book 5 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-7
1
2
34
5
6
7
8
9
10
11
12
13

Do not change the drivetrain spec-
ifications (chain, sprockets,
wheels, tires, etc.).

Do not remove or alter the O2 sen-
sor, air induction system, or ex-
haust parts (catalysts or EXUP,
etc.).

Maintain the drive chain properly.

Maintain correct tire pressure.

Maintain proper brake pedal
height to prevent rear brake from
dragging.

Do not operate the vehicle in an
extreme manner. For example, re-
peated or excessive opening and
closing of the throttle, racing, burn-
outs, wheelies, extendedhalf-clutch use, etc.
EAU91500
ABS warning light “ ”
In normal operation, the ABS warning
light comes on when the vehicle is
turned on, and goes off after traveling
at a speed of 5 km/h (3 mi/h) or higher.TIPIf the warning light does not work as de-
scribed above, or if the warning light comes on while riding, the ABS may not
work correctly. Have a Yamaha dealer
check the vehicle as soon as possible.
WARNING
EWA21120
If the ABS warning light does not
turn off after reaching 5 km/h (3
mi/h), or if the warning light comes
on while riding: 
Use extra caution to avoid pos-
sible wheel lock during emer-
gency braking.

Have a Yamaha dealer check thevehicle as soon as possible.
EAU88350
Immobilizer system indicator light
“”
When the main switch is turned off and
30 seconds have passed, the indicator
light will flash steadil
y to indicate the im-
mobilizer system is enabled. After 24
hours have passed, the indicator light
will stop flashing, however the immobi-
lizer system is still enabled.TIPWhen the vehicle is turned on, this light should come on for a few seconds and
then go off. If the light does not come
on, or if the light remains on, have a
Yamaha dealer check the vehicle.
Transponder interference
If the immobilizer system indicator light
flashes in the pattern, slowly 5 times
then quickly 2 times, this could be
caused by transponder interference. If
this occurs, try the following.
1. Make sure there are no other im- mobilizer keys close to the main
switch.
2. Use the code re-registering key to start the engine.
3. If the engine starts, turn it off, and try starting the engine with the
standard keys.
4. If one or both of the standard keys do not start the engine, take the
vehicle and all 3 keys to a Yamaha
dealer to have the standard keys
re-registered.
EAU91472
Stability control indicator light “ ”
This indicator light flashes when the
traction control system, SCS, or LIF
BEA-28199-E0.book 7 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-9
1
2
34
5
6
7
8
9
10
11
12
13
EAU96241
DisplayThe following items can be found on the
display:
TIPThis model uses a thin-film-transistor
liquid-crystal display (TFT LCD) for
good contrast and readability in various
lighting conditions. However, due to the
nature of this technology, it is normal
for a small number of pixels to be inac-tive.
WARNING
EWA18210
Stop the vehicle before making any
setting changes. Changing settings
while riding can distract the opera-
tor and increase the risk of an acci-dent.
Speedometer
The speedometer shows the vehicle’s
traveling speed.TIPThe display can be switched between
kilometers and miles. See “Unit” onpage 4-18.
Tachometer
The tachometer shows the engine
1. Tachometer
2. Speedometer
3. Quick shifter indicator “QS”
4. Transmission gear display
5. Vehicle information displays
6. Settings MENU icon “ ”
7. Grip warmer indicator (option)
8. Brake control icon “BC”
9. Clock
10.MODE display
11.Lap timer
12.Oil pressure warning “ ”
13.Coolant temperature warning “ ”
14.Auxiliary system warning “ ”
15.Error mode warning “Err” (replaces clock when activated)
LAP 02LATEST
00:12.34
00:01.23
4
1
2
7
6
9
10
8
1135
14 13
12
15
BEA-28199-E0.book 9 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-13
1
2
34
5
6
7
8
9
10
11
12
13 Clock
The clock uses a 12-hour time system.
See page 4-19 to set the clock.
Quick shifter indicator “QS”
When able to shift, the respective QS
or turns green.
When unable to shift, QS is
white.
If the quick shifter function is turned
OFF, QS itself is not displayed.
The quick shifter functions can be
turned on or off in the setting MENU.
See page 4-17.
TIPThe upshift and downshift functions are
independent and can be activated sep-
arately.
For more information on the quick shift-er see “Quick shifter” on page 3-6.
Setting menu icon “ ”
Choose this icon and press the wheel
switch inward to change the settings
MENU screen. (See page 4-15.)
Grip warmer indicator (Option)
The grip warmers can be used when the engine is running. There are 10
temperature levels. When activated,
the indicator will display the tempera-
ture level from 1 (lowest) to 10 (high-
est).
To activate the grip warmer, use the
wheel switch to highlight the grip warm-
er display with the cursor.
Press the wheel switch inward to select
the grip warmer function.
Once selected, rotate the wheel switch
up and down to adjust the temperature
level.
Press the wheel switch inward to con-
firm the temperature level and exit the
grip warmer function.
NOTICE
ECA17932

Be sure to wear gloves when us-
ing the grip warmers.

Do not use the grip warmers in
warm weather.

If the handlebar grip or throttle
grip becomes worn or damaged,
stop using the grip warmers andreplace the grips.
The function of the wheel switch can be
locked into grip warmer mode by press- ing and holding the wheel switch inward
while the grip warmer indicator is high-
lighted by the cursor.
In this mode, the temperature levels
can be instantly adjusted by rotating the
wheel switch up/down.
To exit this mode and return the wheel
switch to its normal functionality, press
and hold the wheel switch inward.
TIPThe current grip warmer setting issaved when the vehicle is turned off.
Lap timer
This stopwatch function can be activat-
ed through the setting MENU. (See
page 4-16.)
Once activated, the vehicle information
display is replaced with:
BEA-28199-E0.book 13 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-14
1
2
345
6
7
8
9
10
11
12
13
To start the timer, press the dimmer/
pass switch down towards “PASS”.
Each press of the dimmer/pass switch
will increase the lap count by 1 and re-
set the current lap timer.
To pause the lap timer, press the wheel
switch inward.
To unpause the timer, press the dim-
mer/pass switch down towards “PASS”
and the timer will resume without count-
ing a new lap.
To exit the lap time mode, turn it off in
the settings MENU. (See page 4-16.)
TIP
The engine must be running to start the lap timer.

The headlight will flash when the
dimmer/pass switch is pressed.

Whenever the lap timer is paused,
it can be resumed using the dim-mer/pass switch.
Brake control icon “BC”
This icon is replaced by the auxiliary
system warning and coolant tempera-
ture warning indicators when they are
activated.
For more information on the BC system
see “BC” on page 3-6.
Error mode warning “Err”
When an internal error occurs (e.g.,
communication with a system controller
has been cut off), the error mode warn-
ing will appear as follows.
“Err” and “ ” indicator light indicates
an ECU error.
“Err” only indicates an ABS ECU error.
TIPDepending on the nature of the error,
the display may not function properly
and the traction control system settings
may be impossible to change. Addition- ally, ABS may not function properly.
Use extra care when braking and have
a Yamaha dealer check the vehicle im-
mediately.
Auxiliary system warning “ ”
This icon appears if a problem is de-
tected in a non-engine-related system.
Coolant temperature warning “ ”
This icon appears if the coolant temper-
ature reaches 116 
C (241 F) or high-
er. Stop the vehicle and turn off the
engine. Allow the engine to cool.NOTICE
ECA10022
Do not continue to operate the en-gine if it is overheating.
Oil pressure warning “ ”
This icon appears when the engine oil
pressure is low. When the vehicle is
first turned on, engine oil pressure has
yet to build, so this icon will come on
and stay on until the engine has been
started.
1. Lap count
2. Current lap time
3. Latest/Previous lap time
LAP
02
LATEST
00:12.34
00:30.23
2
1
3
BEA-28199-E0.book 14 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-15
1
2
34
5
6
7
8
9
10
11
12
13
TIPIf a malfunction is detected, the oil pres-sure warning icon will flash repeatedly.NOTICE
ECA26410
Do not continue to operate the en-gine if the oil pressure is low.
EAU9145B
Settings MENUThe settings MENU screen contains
the following settings modules. Select a
module to make related settings chang-
es. Settings MENU access and opera-
tion
How to use the settings MENU:
Rotate the wheel switch up or down to
highlight items or increase/decrease
values and briefly press the wheel
switch inward to confirm the selection.
Press and hold the wheel switch until
the screen returns to the main display
to exit the MENU at any time.
TIP
Certain settings menu screens
have an upward pointing triangle
mark item. Select the triangle mark
to save settings changes and exit
the current screen.

Should vehicle motion be detect-
ed, the screen will automatically
exit the settings MENU and return
to the main display.

To ensure that the desired settings
changes are saved, be sure to exit
Module
Description
“Exit” Exit MENU and return the
main display
“Display
Setting” Switch lap time mode
on/off and adjust the
tachometer color
“Manual TCS
Setting” Adjust traction control
system/SCS/LIF settings
for the “TCS-MODE M”
“Vehicle
Setting” Adjust BC/quick shifter
settings
“Shift Indicator” Turn the shift indicator
on/off and adjust
tachometer settings
“Maintenance” View and reset
maintenance intervals
Display Setting
Exit
Manual TCS SettingVehicle SettingShift Indicator
km/h
MENU
“Unit”Set fuel consumption and
measurement units
“Brightness” Adjust screen brightness
“Clock” Adjust the clock
“All Reset” Return all settings to
factory default
BEA-28199-E0.book 15 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-16
1
2
345
6
7
8
9
10
11
12
13
each menu via the triangle mark (if
displayed). Exiting the settings
menu by pressing and holding the
wheel switch may not save set-
tings changes.
“Display Setting”
This module allows you to switch the
lap time mode and tachometer color
mode ON/OFF.
When the lap time mode is selected,
the twin vehicle in formation displays on
the main screen will display a lap timer
and a lap counter. To exit the lap time
mode, the turn lap timer OFF in the dis-
play setting module.
To change the tachometer to color
mode, select ON. “Manual TCS Setting”
This module allows you to customize
the “TCS-MODE M” which is accessi-
ble on the main display using the
MODE switches.
Traction control system
This model uses a variable traction
control system. For each setting level,
the further the vehicle is leaned over,
the greater the amount of traction con-
trol (system interv
ention) is applied.
There are 3 setting levels available for
the “TCS-MODE M”.
Setting level 1 applies the least amount
of overall system intervention, while
setting level 3 applies the greatest
amount of overall traction control.
TIP
The traction control system can
only be turned on or off via the
main screen using the MODE
switches.

SCS and LIF can be turned off in-
dependently of traction control
system for “TCS-MODE M”.

When “TCS-MODE” has been set
to “OFF” on the main screen: trac-
tion control system, SCS and LIFare all turned off together.
SCS
SCS can be set to OFF, 1, 2, and 3.
OFF turns the slide control system off,
setting level 1 provides the least
amount of system intervention, and set-
ting level 3 provides the greatest
amount of system intervention.
LIFLIF can be set to OFF, 1, 2, and 3.
Setting level 1 provides the least
amount of system intervention and set-
ting 3 most strongly reduces the rate of
wheel lift.
OFF turns LIF off.
Lap Time OFFTacho Color OFF
km/h
Display Setting
TCS 1SCS 1LIF1
km/h
Manual TCS Setting
BEA-28199-E0.book 16 ページ ２０２１年１２月１日　水曜日　午後７時８分