Periodic maintenance an d a djustment
7-11
7
5. Clean the sponge material with
solvent, and then squeeze the re-
maining solvent out. WARNING!
Use only a d ed icated parts
cleanin g solvent. To avoi d the
risk of fire or explosion, do not
use gasoline or solvents with a
low flash point.
[EWA10432] NOTICE:
To avoi d damag ing the foam
material, han dle it g ently an d
carefully, an d d o not twist or
wrin g it.
[ECA10512]
6. Apply oil of the recommended
type to the entire surface of the
sponge material, and then
squeeze the excess oil out.
TIP
The sponge material should be wet but
not dripping.
7. Insert the mesh and the spongematerial into the air filter case.
NOTICE: Make sure that the
mesh an d the spon ge material
are properly seated in the air fil-
ter case. The en gine shoul d
never be operated without the
mesh an d the spon ge material installe
d, otherwise the pis-
ton(s) an d/or cylin der(s) may b e-
come excessively worn.
[ECA15573]
8. Install the air filter case cover by installing the screws.
TIP
Make sure that the spark plug lead is
inserted into the guide as shown.
9. Install the panel.
To clean the air filter check hose
1. Check the hoses at the bottom of the air filter case for accumulated
dirt or water.
Recommen ded oil:
Yamaha foam air filter oil or other
quality foam air filter oil
1. Spark plug lead
2. Guide
1
12
UBMA80E0.book Page 11 Wednesday, October 20, 2021 8:57 AM
Specifications
9-2
9
Spark plug(s):
Manufacturer/model:
NGK/CR6HSA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type:Wet, centrifugal, shoe + multiple-disc
Drivetrain:
Primary reduction ratio:3.722 (67/18)
Final drive: Chain
Secondary reduction ratio:
2.500 (35/14)
Transmission type:
Constant mesh 4-speed
Gear ratio: 1st:
3.167 (38/12)
2nd: 1.941 (33/17)
3rd: 1.381 (29/21)
4th:
1.095 (23/21)
Chassis:
Frame type:Backbone
Caster angle:
26.0 °
Trail: 60 mm (2.4 in)
Front tire:
Type:
With tube
Size: 2.50-14 4PR
Manufacturer/model: CHENG SHIN/C-803
Speed rating:
120 km/h (75 mph)
Rear tire:
Type:With tube
Size:
3.00-12 4PR
Manufacturer/model: CHENG SHIN/C-803 Speed rating:
120 km/h (75 mph)
Tire air pressure (measure d on col d
tires):
Front:
100 kPa (1.00 kgf/cm², 15 psi)
Rear: 100 kPa (1.00 kgf/cm², 15 psi)
Front wheel:
Wheel type: Spoke wheel
Rim size: 14 x 1.40
Rear wheel:
Wheel type:
Spoke wheel
Rim size: 12 x 1.60
Front brake:
Type:
Mechanical leading trailing drum brake
Rear brake:
Type:
Mechanical leading trailing drum brake
Front suspension:
Type:Telescopic fork
Spring: Coil spring
Shock absorber:
Hydraulic damper
Wheel travel: 115 mm (4.5 in)
Rear suspension:
Type:
Swingarm
Spring: Coil spring
Shock absorber: Gas-hydraulic damper
Wheel travel:
110 mm (4.3 in)
Electrical system:
System voltage:12 V
Ignition system:
CDI
Charging system: AC magneto
UBMA80E0.book Page 2 Wednesday, October 20, 2021 8:57 AM
